problems

[small heart]

axes map is still in Beta and at the moment irrelevant

you can go on and provide the remaining things 🙂

[vocal nexus]

Thanks!

[small heart]

please read the posting guidelines again and provide whats required 🙂 take your time and double check u have everything

[vocal nexus]

Voron v0.2r1
Mods are canbus ebb36 and bentomini.

Running suggested shapers some resonance only on one side of the cube

my vibrations graph isnt looking to great with my peaks being right in ideal printing speeds

[plush summit]

After you fix homing speed in tmc_autotune I would rerun vibrations just to see where it is at

[vocal nexus]

would changing my shaper to ei change any of these results are does this look decent ?

[plush summit]

are you using 2209's

[vocal nexus]

Yep

Btt pico

[plush summit]

what is your inter and ext perimeter speeds

[vocal nexus]

120 external and 200 internal

So i would need to bump external

[plush summit]

I would either go up or down. You want to stay in the low part of the green zones

[vocal nexus]

I'll bump them up and re test

[vocal nexus]

have printed at a wall speed of 128 and 96 and the ripples still apear on only one side of the cube

[plush summit]

can you post all four sides of the cube please

[vocal nexus]

is that possibly cooling related ?

[plush summit]

what accel and speed are your using for perimeters

Also did you increase your run current for x and y motors

[vocal nexus]

outer was like 98 and inner 200

and no i did not should i ?

[plush summit]

accel and speeds please

can you also post your 3mf for the voron cube please. And, please tell me what slicer you are using

[vocal nexus]

orca slicer

3000 accel and 96 mm for out war 5000 and 200 mm/s for inner wall.

[plush summit]

can you post what you are using for input shaper please

I think I see the issue

in filament uncheck "slow printing down for better layer cooling"

that autocooling feature is slowing your perimters down to 105 ish mm/s

[vocal nexus]

[input_shaper]
shaper_freq_x: 92.6 # center frequency for the X axis filter
shaper_type_x: mzv # filter type for the X axis
shaper_freq_y: 66.6 # center frequency for the Y axis filter
shaper_type_y: mzv # filter type for the Y axis
damping_ratio_x: 0.051 # damping ratio for the X axis
damping_ratio_y: 0.053

okay will do

[plush summit]

also set ext perimter speed to 90

[vocal nexus]

okay

[plush summit]

in input shaper set y to EI

change it's freq accordingly

then repring a cube: 3 perimters/bottom, 0 infill/top

[vocal nexus]

made it much better but still there

possibly vfa ?

only on that side of the print. all else is perfect

[plush summit]

can you post pictures please

[plush summit]

This is looking like a motion thing. Because every other side looks good. @lilac sand what are your thoughts

[vocal nexus]

That's a bit better of a shot. At it.

[lilac sand]

How is the nozzle of the machine? Because, this can also be a wear/damaged nozzle for example

[vocal nexus]

New revo 0.4

[lilac sand]

Do you have another one to test to be sure?

[vocal nexus]

I do I can swap it

[lilac sand]

Ok super. It might be something else, but at least this way we can validate it and remove the nozzle from the equation

[vocal nexus]

i will swap nozzle and print another test

[vocal nexus]

Not nozzle. I'm thinking

[plush summit]

@lilac sand This is odd that it is only showing on one side of y

[vocal nexus]

Been scratching my head over that as well. As newb as I am with core xy. Still seems odd.

[plush summit]

can you reprint the cube at the front of the build plate, rather than in the middle

wondering if it is a motion system issue

[vocal nexus]

yeap

ldo kit with a hiwin on x so decent parts id think but you never know

[lilac sand]

Yes it's partly why I thought it could be a nozzle issue. On my machine I already saw stringing appearing on only one side of prints due to this (nozzle was damaged due to a steel brush).

But moving the print to another location is a good idea

[vocal nexus]

whats a good run current setting for x and y ?

[small heart]

rule of thumb is that u want the lowest possible run current without losing steps.
the default in the github config is a good starting value.

[small heart]

also just noticed u did not yet click on your flag in #rules . Make sure to do that if u find the time 🙂

[vocal nexus]

flag clicked

not much of a change

[vocal nexus]

It's a stump forsure.

[vocal nexus]

im getting alot smoother motor graphs when i bump my amperge up to 0.8 on x and y

can v0 motor mounts handle this current ? makes my low end speeds alot smoother in peaks

[small heart]

0.8 is the default as i mentioned before, isnt it?

[vocal nexus]

i think ldo was 0.5 which im running

but i did a vibration test at 0.8 and it smooths out the lower speeds for me vibration wise

[small heart]

ah okay the default VORON 0.2 config lets u calculate the current. thats actually smart

[vocal nexus]

yep

ive just noticed my motors seem to like the bit higher amperage

[small heart]

0.8 should be fine but best would be to check with the datasheet

[vocal nexus]

ldo says 1.5

[small heart]

thats max

[vocal nexus]

yeah just dont wanna melt anything

[small heart]

as long as u dont have cheap esun ABS+ its totally fine

[vocal nexus]

yeah these are asa parts

was looking at your config you ru n 2240?\

[small heart]

yes

[vocal nexus]

didnt think btt made an ez varient of them

[small heart]

nope they dont

[vocal nexus]

what board are you using ?

[small heart]

SKR 3 EZ

[vocal nexus]

ah skr ez alows both