Error after updating klipper and after trying to update mcus nothing helps | VORONDesign | Page 1

errant oar Jun 1, 2024, 1:02 AM

#


This is frequently caused by running an older version of the
firmware on the MCU(s). Fix by recompiling and flashing the
firmware.

Your Klipper version is: v0.12.0-207-g6cd17420-dirty
MCU(s) which should be updated:
mcu: Current version v0.12.0-112-g72b301a2
EBBCan: Current version v0.12.0-112-g72b301a2
beacon: Current version Beacon 1.1.0
Up-to-date MCU(s):
<none>```

orchid wharf Jun 1, 2024, 1:12 AM

#

Update beacon.

#

Ssh in
CD beacon dir
./install.sh

#

Reboot

errant oar Jun 1, 2024, 1:21 AM

#

fixed that

#

now have this issue

#

Once the underlying issue is corrected, use the
"FIRMWARE_RESTART" command to reset the firmware, reload the
config, and restart the host software.
Printer is shutdown```

#

any idea how to fix it?

#

tried homeing x and y and get this error for both

orchid wharf Jun 1, 2024, 1:29 AM

#

That usually means a wiring issue wit that motor.

#

Is this new?

errant oar Jun 1, 2024, 1:30 AM

#

yeah

#

i did rewire the printer

#

but didnt get the error before

#

did i switch wire pairs or smt?

#

I had an issue that some of my motors weren't spinning freely when the printer was off

#

and I googled how to wire a motor and followed it

orchid wharf Jun 1, 2024, 1:32 AM

#

Motor coil pairs are flipped. Swap middle 2 pins.

errant oar Jun 1, 2024, 1:32 AM

#

thank oyu

orchid wharf Jun 1, 2024, 1:32 AM

#

You need to find the coil pairs tho. But start there

errant oar Jun 1, 2024, 1:34 AM

#

I swear I don’t do wiring while drunk

orchid wharf Jun 1, 2024, 1:46 AM

#

That would do it

errant oar Jun 1, 2024, 1:49 AM

#

it still exists

#

even after that was fixed

#

#

I swapped all the middle pairs and it still does it

orchid wharf Jun 1, 2024, 2:00 AM

#

Then find the coil pairs. Do you have a multimeter

errant oar Jun 1, 2024, 2:01 AM

#

orchid wharf Then find the coil pairs. Do you have a multimeter

i have a multimeter but how?

orchid wharf Jun 1, 2024, 2:01 AM

#

Pick 2 wires. Test for continuity. If it beeps. That's a pair. And now you know the other one too. If not pick a different wire.

Eventually you will have 2 pairs. That's coil a and b

Most MCUs want aabb

So just wire it that way.

#

I'm would have just done one motor as a test tho hehe

errant oar Jun 1, 2024, 2:07 AM

#

I lost sanity working on this printer so i kinda forgot how to do things correctly

#

all motors should be good now

#

earlier today my spool holder got eaten by my MagnetoX so not amazing luck with printers today

#

so uhm

#

it works but

#

the z move with the x and y when trying to home

orchid wharf Jun 1, 2024, 2:18 AM

#

errant oar the z move with the x and y when trying to home

Z will go up before homing so the nozzle doesn't drag the bed. Did you do the initial voron startup guide?

errant oar Jun 1, 2024, 2:23 AM

#

orchid wharf Z will go up before homing so the nozzle doesn't drag the bed. Did you do the in...

i did but havent done it in over 1yr

#

i fixed it though

#

Z drives were moving in the wrong direction

orchid wharf Jun 1, 2024, 2:30 AM

#

The voron startup guide will do all that. Do it all

errant oar Jun 1, 2024, 2:33 AM

#

it is now all fixed luckily

#Error after updating klipper and after trying to update mcus nothing helps