klipper_kalico_help
Cannot connect to printer IP.
Connectivity
CB1 Cannot connect to Manta M8P ls /dev/serial/by-id/ not working
Installation
Solved
Connectivity
Flashing
I want to control a WS2812 LED strip with RPi as secondary MCU, but it only lights up bright white.
Config
Cannot Connect to Moonraker
Connectivity
Error messages
Config
Voron 2.4R2 printer HeightMAP
Installation
Canbus can't control toolhead
Installation
Config
auto_z_calibrate offset gone after bed_mesh_calibrate
Solved
Macros
Meshing & probing
Fysetc Catalyst Re-flashing help
Error messages
Clicked update bttn
Config
Flashing
Hit the Update button, trying to reflash all my boards
Solved
Clicked update bttn
Flashing
nube needs help -- klipper - mcu can't connect.
Installation
Config
Flashing
SPIDER 3.0 and Mini12864 beeper configuration
Connectivity
Solved
Config
TEMPERATURE_WAIT doesn't delay out from M117 + action_respond_info()
Macros
How do I config Klipper for the Stridemax dual FD?
Error messages
Sensorless Homing
Solved
Macros
Config
klipper_z_calibration.cfg
Installation
Meshing & probing
Error messages
Config
Macros
Move out of range: 18.439 -4.370 0.350 [-2.000]
Config
BTT pi v1.2 + SKR Pico "The klippy host software is attempting to connect."
Installation
Solved
Connectivity
Flashing
Extrude below minimum temp Error when trying to print
Error messages
Macros
Config
Klipper doesnt see my Mcu
Connectivity
Error messages
Toggles in mailsail ?
Macros
Internal error on command:"G3" / MCU connection lost
Error messages
Issues with initial setup of motor direction with voron 2.4 BTT Octopus.
Config
wifi shows connected but there is no access.
Connectivity
Config
Giving up on Wifi.
Connectivity
LDO switchwire, any attempt to move in any axis results in error
Error messages
Can't get the flash-sdcard.sh script to flash firmware to the Octopus 1.1 board.
Flashing
Klipper reports: SHUTDOWN (temperature issue)
Config
another MCU not connecting, Klipper not ready post
Connectivity
Installation
Flashing
KAMP not working properly
Meshing & probing
ls: cannot access '/dev/serial/by-path/*': No such file or dir
Error messages
How do I gain access to my printer/Klipper from my desktop to fix a config issue.
Error messages
mac stopped finding machine
Connectivity
Error after editing printer.cfg
Error messages
Several different MCU Shutdowns
Error messages
Stuck on this error for Klipper install
Flashing
MCU 'EBB' shutdown: Timer too close
Error messages
TMC5160t plus with a octopus pro board Fixed
Error messages
Config
klipper screen orange pi
Klipperscreen
switchwire bed mesh was working but not anymore.
Solved
Meshing & probing
Bed Mesh Problems not square
Meshing & probing
adaptive bed mesh not meshing
Macros
Meshing & probing
mcu protocol error
Error messages
Changing Klipper repo to a different mirror
Installation
Default Mesh won't load in Klipper
Error messages
Clicked update bttn
Config
Meshing & probing
MCU timer too close
Installation
Connectivity
voron v0.1-s1 klipper install+printer config
Installation
Config
heater_extruder not heating at expected rate in a cold room
Error messages
Config
Klipper Backup Github error
Error messages
M8p v1.1 & sb2209 guide?
Flashing
Can't understand why a valid pin is invalid causing shutdown
Error messages
Config
Solved