klipper_kalico_help
Bed_Mesh_calibrate not compensating.
Meshing & probing
Sensorless homing X always triggered.
Config
idle_timeout during printing
Error messages
Solved
Moonraker can't connect to Klipper!
Connectivity
Annoying error messages during print [Problem Solved]
Error messages
Printer nowhere near set speed
Config
Klipperscreen installation help
Installation
klipper expansion board+creality 4.2.2 install help
Installation
Solved
Connectivity
Flashing
PT1000 sensor ADC out of range -38 degrees
Error messages
Config
Solved
PROBLEM WITH EDDY - KLIPPER
Installation
Kernel Panic: Do I need to reinstall or can I recover?
Installation
Error messages
Option 'pin' in section 'probe' must be specified
Installation
First print from coldstart Z-Offset is bad... after that, all good
Macros
Error running dfu-util : Error while flashing Octopus via USB and the raspberry pi
Flashing
Voron 0.2 with V0 Display: Klipper does not start correctly if display is connected during power-on
Installation
Error messages
Connectivity
klippy says printer not ready but ls /dev...... does give a serial, can't seem to reflash the bin
Connectivity
Error messages
Config
Flashing
Issues with Beacon Installation
Error messages
RPi bookworm OS crashing on boot, bullseye OS works
Installation
Solved
Connectivity
Issue after plugging in Beacon
Error messages
Clicked update bttn
Can't flash BTT Octopus with Klipper
Installation
Flashing
Option 'aliases' in section 'board_pins board_are_here' must have 2 elements
Solved
heater extruder not heating at expected rate error
Error messages
inductive probe issues with Klipper/Mainsail
Config
Can't connect to moonraker, can't remember my pi password anymore. Best course of action?
Connectivity
Config
MCU 'mmu' shutdown: Timer too close
Error messages
Klipper crashing mid print
Connectivity
Error messages
Solved
'mcu/EBBCAN': Unable to connect. EBB can has stopped working
Connectivity
Error messages
Solved
Flashing
KLIPPER MCU VERSION ERROR
Error messages
Print error; "Move Out of Range" after bed leveling is done
Error messages
pt1000 Chamber temp on Manta M8P in TH0
Installation
set_kinematic_position query - what affect on maximum_x/y/z?
Config
TEMPERATURE_WAIT SENSOR=<config_name> [MINIMUM=<target>] [MAXIMUM=<target>]
Solved
Macros
eddy Unknown command:"BTT_BED_MESH_CALIBRATE"
Error messages
Klipperscreen
Config
problem
Config
MCU 'head' shutdown: ADC out of range
Error messages
my.mainsail.xyz not working on desktop
Connectivity
Can i use one sensor for both X and Y homing?
Config
Can't get to mainsail
Solved
V0 display not connecting
Klipperscreen
Error messages
Connectivity
Config
Solved
Manta M8P lsusb doesn't detect EBB SB2209 (RP2040) in DFU mode
Connectivity
Solved
Config
Flashing
ADXL345 - When it is no longer bad wiring and it is bad adxl?
Connectivity
Error messages
bigtreetech tft43 cannot connect to raspberry pi 4
Installation
Cannot get Camera to work after moving from one Klipper setup to another
Installation
Solved
Klipperscreen
Camera
Spider 2.2 mcu not found after restarting printer
Connectivity
Flashing
Not sure how to read pinout diagram to tell klipper.
Connectivity
Config
Cant get rpi cam v3 to work
Camera
MCU Protocol errorThis is frequently caused by running an older version of thefirmware on the MCU
Error messages
Can't get Klipper to compile
Installation
Heater Bed reading innacurate temperatures
Solved
Config
Keep getting mcu 'toolhead': Unable to connect error after installing new toolhead board
Installation
Solved
Flashing