klipper_kalico_help
z calibrate
Error messages
Macros
Config
Z Offset changes tad too high after first print
Solved
Macros
Config
Cartographer 'z_virtual_endstop' is only useful as an endstop pin
Error messages
Merge Two Printer Histories
Config
Random “MCU: unable to connect” during prints on Beacon
Error messages
Solved
Internal error during connect: 'MCU' object has no attribute 'register_response'
Installation
Extrude below minimum temp after leveling
Config
Bed fans with Ellis's .cfg
Config
Printing past bed mesh - bad Z offset
Meshing & probing
Toolchanger not changing tools
Config
RecursionError: maximum recursion depth exceeded
Error messages
X/Y Endstops triggering, direction correct, motors not stopping on home
Solved
Config
Printer bricked after update
Error messages
Config
Solved
Clicked update bttn
Flashing
Sensorless homing - printer homing outside of limits.
Solved
Leviathan 1.2 flashing
Solved
Flashing
No luck reflashing klipper after update to 577
Installation
Error messages
Solved
Flashing
Cartographer w/ Axis Twist
Solved
Meshing & probing
/tmp/klipper_host_mcu-bash: /tmp/klipper_host_mcu: Permission denied
Installation
Error messages
Solved
Sensorless Homing - X and Y move out of range
Solved
Config
Klipperscreen not turning on
Klipperscreen
"Must home axes first" error, sensorless homing
Config
Raspberry pi crashing
Connectivity
Cannot connect to Moonraker
Klipperscreen
Error messages
Connectivity
Config
Solved
Klipper setup guide
Config
Strange Pits/Lands on Eddy Coil (EBB36) Rapid Scan on new build with Eddy NG
Meshing & probing
Flashing LDO Leviathan 1.3
Error messages
Solved
Flashing
Getting back into printing after 8 months, cant figure out how to update klipper.
Solved
Flashing
nozzle brush error
Macros
BTT PI 2 Upgrade gone wrong, not being able to reflash mcu
Error messages
Solved
Klipper shuts down after being idle for a few mintues
Error messages
TMC 'stepper_x' reports error: GSTAT: 00000002 drv_err=1(ErrorShutdown!)
Error messages
Solved
mcu 'mcu': Unable to open serial port
Error messages
Solved
timer too close error, spike on sshd
Error messages
problem with save_config
Config
Klipper Homing Issues
Installation
Error messages
Meshing & probing
How to use the BTT Smart Filament Sensor switch in two seperate configs
Solved
Macros
Config
Assistance with LOAD and UNLOAD macros (pancake motor stalls)
Solved
Macros
Config
Timer too close when heating hotend
Error messages
Setting up ebb36 v1.2
Config
I need help installing klipper
Klipperscreen
Fysetc H36 board issues (trying to sort out config for fans etc)
Solved
Flashing
Display Error after update
Error messages
Solved
Octopus V1.1 SD Card LED not lighting / not flashing
Flashing
Help needed with sensorless TMC2240 setup on Octopus Pro 1.1 please
Solved
Config
Getting timer to close errors with toolhead 2 on my stealthchanger
Error messages
Solved
Beacon and sensor-less homing
Config
I am having trouble updating my OS Packages in Mainsail
Installation
Flashing
Klipper Macro help, changing fan macro
Solved
Macros
Small issue with my print_start macro (Using Jontek's but modified)
Macros
Can anyone help me make heads or tails of this?
Error messages