klipper_kalico_help

Help! Large X-Y shifts during printing 13 messages

Apr 9, 2025, 5:41 AM Solved

Mainsail not appearing 33 messages

Apr 8, 2025, 10:12 PM Connectivity

Unknown pin chip name 's03' 5 messages

Apr 7, 2025, 6:48 AM Error messages

Klipper ignoring bed temp setpoint 11 messages

Apr 6, 2025, 6:25 PM Solved Config

Unable to read tmc uart 'stepper_[axis]' register GCONF 31 messages

Apr 6, 2025, 4:39 PM Connectivity Config

Issues with creating klipper firmware for ebb36 26 messages

Apr 6, 2025, 4:29 PM Solved Flashing

Lost communication with MCU 'EBB 2 messages

Apr 6, 2025, 8:31 AM Error messages

TMC2660 sensorless homing on Duet2 12 messages

Apr 5, 2025, 7:00 PM Solved Config

installed 4-wire Noctua on Stealth Burner 3 messages

Apr 5, 2025, 12:19 PM Config

goin a lil nutty. voron 2.4 r2, enabled bed mesh, move out of range, maybe QGL? 43 messages

Apr 5, 2025, 2:00 AM Error messages

Question on static output pin declarations 27 messages

Apr 4, 2025, 10:28 PM Solved Config

Solved. K500 thermocouple install 60 messages

Apr 4, 2025, 6:55 PM Solved

Cancel Print Macro help 53 messages

Apr 4, 2025, 5:13 PM Macros Config

X & Y Homing uses Z-Motors 11 messages

Apr 4, 2025, 11:04 AM Config

M8B fan set up error 9 messages

Apr 3, 2025, 7:15 PM Solved Macros

Tried updating firmware and nothing works anymore 46 messages

Apr 1, 2025, 4:20 PM Installation Solved Flashing

PT100 on Nighthawk? 6 messages

Mar 31, 2025, 10:24 PM Solved Config

Z-offset only correct after power cycling printer 7 messages

Mar 31, 2025, 5:03 PM Meshing & probing

Printer doesn't Pause when done directly on printer 36 messages

Mar 31, 2025, 2:37 AM Macros

Klipper Toolchange 2 messages

Mar 30, 2025, 2:10 PM Installation Config Flashing

Second homing move goes the wrong way and only a little 3 messages

Mar 29, 2025, 7:55 PM Macros

Klipper update issue 6 messages

Mar 29, 2025, 4:01 AM Solved

Extruder not hot enough 14 messages

Mar 28, 2025, 7:14 PM Error messages

[fixed] raspberry pi freezes at seemingly random times and on reboots 43 messages

Mar 27, 2025, 5:18 PM Connectivity Error messages Solved

EBB 2209 USB Can Bus from BTT 46 messages

Mar 27, 2025, 5:08 PM Installation Error messages Connectivity Config Flashing

BTT Smart Filament Sensor v2 Immediate Pause 11 messages

Mar 27, 2025, 1:58 PM Macros

Home all oddities 9 messages

Mar 26, 2025, 7:13 PM Config

(Flygemini v3) Understanding Bootloaders and USB to Can Bridge 4 messages

Mar 25, 2025, 10:59 PM Installation Flashing

START_PRINT macro issues 28 messages

Mar 25, 2025, 5:16 PM Solved Macros Config

Just a little problem 2 messages

Mar 24, 2025, 2:30 PM Solved Config

Control one fan with either RPi or MCU temp 17 messages

Mar 24, 2025, 12:43 PM Solved Macros Config

Slow movement before print start 2 messages

Mar 24, 2025, 3:17 AM Config

Temperature Spike on Power On 3 messages

Mar 23, 2025, 4:40 AM Solved Config

Stealthburner RGB problems with BTT SB2209 Canbus Board 6 messages

Mar 22, 2025, 11:16 PM Connectivity Solved

Printer is not readyThe klippy host software is attempting to connect. 46 messages

Mar 22, 2025, 8:46 PM Connectivity

klipper error with usb hub zero4u 2 messages

Mar 22, 2025, 6:48 PM Error messages

Temporarily allow -Z axis travel in macro 26 messages

Mar 21, 2025, 2:07 AM Macros

Voron 2.4 Sensorless XY homing with TAP Config 28 messages

Mar 20, 2025, 1:03 PM Macros Config

Heater extruder not heating at expected rate 4 messages

Mar 20, 2025, 1:42 AM Error messages

_CLIENT_LINEAR_MOVE E=50 F=300 4 messages

Mar 19, 2025, 3:55 PM Error messages Klipperscreen

Can not get the macros as a button on the dashboard 14 messages

Mar 19, 2025, 2:32 AM Macros Klipperscreen

IDM scanner USB PROBLEM 5 messages

Mar 18, 2025, 5:53 PM Config

gpio pin 6 error when trying to start pi with mainsail 3 messages

Mar 18, 2025, 4:42 AM Flashing

Lost klipperscreen please help 18 messages

Mar 17, 2025, 9:49 PM Error messages Klipperscreen

Invalid update manager 24 messages

Mar 17, 2025, 9:07 PM Connectivity Error messages Config Flashing

Constant shutdowns after installing can 9 messages

Mar 16, 2025, 10:13 PM Error messages

Power button LED 2 messages

Mar 16, 2025, 5:18 PM Macros Config

I'm having trouble getting sensorless homing with Mellow Fly HV TMC5160 v1.5 and BTT Octopus 24 messages

Mar 16, 2025, 4:08 PM Installation Config

Octoprint to Mainsail - Error actions - Probe samples exceed samples_tolerance 4 messages

Mar 16, 2025, 3:46 AM Error messages Macros Config Solved

Sensorless homing error : Pin '' is not a valid pin name on mcu 'mcu' 3 messages

Mar 15, 2025, 3:37 PM Error messages Config Solved