klipper_kalico_help

Pi wont cummunicate with the MCU 11 messages

May 18, 2025, 7:27 AM Connectivity Error messages Solved Flashing

Wifi change issue 21 messages

May 18, 2025, 3:01 AM Connectivity

Help for Kliiper install on Sovol Sv06+ 2 messages

May 17, 2025, 8:11 PM Installation Solved

Use tagged commits in moonraker 2 messages

May 16, 2025, 9:32 PM Config

Issue with updating the firmware 2 messages

May 16, 2025, 1:19 PM Solved Flashing

Installing Klipper...pypi.org ReadTimeoutError 21 messages

May 16, 2025, 1:39 AM Installation Error messages

Inductive Probe not triggering (No trigger on probe after full movement) 43 messages

May 14, 2025, 3:48 PM Error messages Solved Meshing & probing

MCU/Pi freeze causing Error: Heater extruder not heating at expected rate? 9 messages

May 14, 2025, 12:15 PM Error messages Solved

Klipper claims no MCUs up to date despite being updated. 10 messages

May 13, 2025, 9:03 PM Flashing

MCU Connection issues. 46 messages

May 13, 2025, 7:33 PM Config

Moonraker having a parsing issue? 9 messages

May 12, 2025, 10:30 PM Config

omron probe 39 messages

May 12, 2025, 7:50 AM Config

Suggestions to not have the printer go through the entire full PRINT_START routine every time 28 messages

May 11, 2025, 7:01 PM Solved Macros Config

Auto bed leveling not working 2 messages

May 10, 2025, 1:57 PM Meshing & probing

For modifying mainsail.cfg, is there anything that I should keep in mind? 6 messages

May 9, 2025, 11:19 PM Solved Macros Config

Klipper shutdown randomly un print.. 10 messages

May 9, 2025, 3:54 AM Connectivity Installation Error messages Config

home_xy_position cannot be used with [homing_override] 9 messages

May 9, 2025, 2:15 AM Error messages Solved

Parameter in PRINT_START 8 messages

May 8, 2025, 7:59 PM Config

need a bit of help, had to redo my sd card due to me somehow screwing it up. 38 messages

May 8, 2025, 3:48 PM Installation

having a wierd issue Can not update MCU 'mcu' config as it is shutdown 4 messages

May 7, 2025, 11:26 PM Connectivity Solved Error messages

Angrycam low fps 14 messages

May 7, 2025, 8:03 PM Solved Camera

Eddy for Bed Mesh and PZ-Probe as Endstop 6 messages

May 7, 2025, 5:58 PM Solved Config Meshing & probing

G-Code Shell Command Extension Broke Klipper 85 messages

May 6, 2025, 9:59 PM Error messages Macros Config Solved

Noisy controller fans 6 messages

May 6, 2025, 1:57 PM Macros Config

Sensorless issue - Voron 2.4R2 - Spider v3 TMC2209 123 messages

May 6, 2025, 1:00 AM Solved Config

Initial MCU connection issues? 51 messages

May 5, 2025, 5:35 PM Connectivity Error messages Config Solved

Unknow source console printing temperatures 2 messages

May 5, 2025, 8:12 AM Solved Config

Klippain Z offset not set 4 messages

May 5, 2025, 5:48 AM Solved Config

MCU Protocol error 280 messages

May 4, 2025, 9:14 PM Error messages

Filament_type variable to Klipper for automatic VOC filter control based on material 16 messages

May 2, 2025, 6:52 PM Solved Macros Config

Lost communication with MCU 'mcu' after 9 hours 36 messages

May 2, 2025, 5:51 PM Connectivity Error messages

Klicky SGTHRS value 36 messages

May 2, 2025, 1:51 PM Solved Meshing & probing

X/Y Distance callibration 20 messages

May 1, 2025, 11:49 AM Config

VFAN2 not working on EBB 2209 2 messages

Apr 30, 2025, 2:00 PM Installation Config

Extruder PID tune not working as expected, ±3 variation while at steady state 3 messages

Apr 29, 2025, 4:00 PM Config

Moonraker reports: DISCONNECTED 19 messages

Apr 28, 2025, 6:13 AM Installation Solved

Error evaluating 'gcode_macro _User_Variables:gcode' 156 messages

Apr 28, 2025, 2:05 AM Installation Error messages Config

Klipper temperature 1024055.008 not in range 10.000:270.000 44 messages

Apr 27, 2025, 5:53 PM Error messages Config

Extruder stops spinning at high speeds with pressure advance enabled 8 messages

Apr 27, 2025, 1:28 AM Connectivity Config

Relative_reference_index 69 messages

Apr 26, 2025, 3:09 AM Solved Clicked update bttn

Using an SKR2 for triple Z driving 22 messages

Apr 25, 2025, 9:54 PM Installation Solved

Thermistor problem 47 messages

Apr 25, 2025, 6:15 PM Config

floating point variable issue 28 messages

Apr 23, 2025, 3:38 PM Macros

This new issue happened out of nowhere. Any any thoughts? 23 messages

Apr 23, 2025, 1:17 AM Connectivity Solved Klipperscreen

ebb 2209 rp2040 11 messages

Apr 22, 2025, 7:10 PM Config Meshing & probing

MCU 'mcu' shutdown: I2C NACK error encountered 4 messages

Apr 21, 2025, 3:25 PM Error messages

Unable to write tmc spi 'stepper_x' register GLOBALSCALER 3 messages

Apr 21, 2025, 12:59 PM Error messages Solved

enderwire z homing in wrong direction 10 messages

Apr 19, 2025, 8:42 PM Config

Manta M8P + CB1: Klipper not finding MCU 3 messages

Apr 19, 2025, 2:36 PM Installation Flashing

[SOLVED] How to get the UUIDs of my CAN devices? 21 messages

Apr 19, 2025, 1:17 PM Connectivity Installation Solved