voron_2_help_forum_public

[Solved] Inductive probe accuracy 21 messages

Dec 26, 2023, 7:00 AM Bed mesh issue Electronics & wiring Mechanical Z Offset Configuration

Nozzle plugging prevantative ideas 7 messages

Dec 26, 2023, 3:51 AM Tuning Configuration

Unable to open serial port: [Errno 2] 8 messages

Dec 26, 2023, 2:07 AM Initial setup Configuration

Y-axis overshooting on every print move in which it changes direction 49 messages

Dec 25, 2023, 8:22 PM Mechanical

I want to understand how homing works on my Voron 2.4 4 messages

Dec 25, 2023, 7:33 PM Initial setup Configuration

[SOLVED] Probe samples exceed samples_tolerance issue 12 messages

Dec 25, 2023, 4:30 AM QGL

z-layer shift after first layer ? 9 messages

Dec 24, 2023, 8:57 PM First layer Initial setup

Nozzle dragging on infill 2 messages

Dec 24, 2023, 4:50 PM Tuning Mechanical Electronics & wiring

first print layer issues 41 messages

Dec 24, 2023, 3:56 PM Bed mesh issue First layer

can't flash spider V3 2 messages

Dec 24, 2023, 9:32 AM Initial setup Electronics & wiring

why is this happening? 16 messages

Dec 24, 2023, 4:17 AM Tuning

switchwire v6 Adaptation 3 messages

Dec 24, 2023, 3:25 AM Kits/parts advice Mechanical Electronics & wiring

Able to Extrude using web interface and purge line from config but does not extrude in prints 7 messages

Dec 24, 2023, 2:33 AM Mechanical First print

config files Manta M8P v2 53 messages

Dec 23, 2023, 9:25 PM Configuration

manta m8p v2.0 2 messages

Dec 23, 2023, 3:54 PM Electronics & wiring

main softwear Voron 2.4 2 messages

Dec 23, 2023, 3:51 PM Initial setup

48v psu on octopus pro 8 messages

Dec 23, 2023, 12:56 PM Kits/parts advice Electronics & wiring

LDO 2.4r2 Rev C Kit - BTT TFT Issue 2 messages

Dec 23, 2023, 10:53 AM Configuration

Layer Separation and Walls not sticking - Ellis SS ABS Profile 21 messages

Dec 22, 2023, 10:15 PM Tuning

Z offset & Klicky Probe - How to get consistent First Layer? 7 messages

Dec 22, 2023, 5:55 AM First layer

MCU 'mcu' shutdown: ADC out of rangeThis generally occurs when a heater temperature exceedsits con 3 messages

Dec 21, 2023, 2:36 PM Printer shutdown

voron 2.4 building endstop problem 2 messages

Dec 21, 2023, 1:45 PM Electronics & wiring

new build 600x600x600 build plate 4 messages

Dec 21, 2023, 1:01 PM Mechanical

[solved] ABS warping, Chamber Temp to low? 39 messages

Dec 21, 2023, 10:59 AM First layer

NeoPixel Refuses to work 31 messages

Dec 21, 2023, 2:51 AM Initial setup Electronics & wiring Configuration

Extreme ringing on my Voron 2.4 58 messages

Dec 20, 2023, 2:20 PM Mechanical

First layer inconsistency 4 messages

Dec 20, 2023, 2:16 PM First layer

Sudden layer problem 6 messages

Dec 19, 2023, 9:53 PM First layer

Hi, my 2.4 e3d revo does not heat up past 180 degrees and I get shocked touching it. 128 messages

Dec 19, 2023, 4:35 PM Printer shutdown Electronics & wiring

Layers are not stacking properly 3 messages

Dec 19, 2023, 10:11 AM Tuning

300mm 2.4 LDO kit - X ,Y Squeak 2 messages

Dec 19, 2023, 1:48 AM Mechanical

Heated bed consistently throws 'not heating at expected rate' around 90c-100c 31 messages

Dec 18, 2023, 10:21 PM Printer shutdown

BELT TENSION WITH Klippain-SHAKETUNE 2 messages

Dec 18, 2023, 9:55 PM Mechanical

Klicky Probe Dock Too High 2 messages

Dec 18, 2023, 8:13 PM Mechanical Solved

After print completed, gantry moved down and damaged print and nozzle 59 messages

Dec 18, 2023, 9:44 AM Initial setup

48V A/B motors 5 messages

Dec 17, 2023, 6:08 PM Electronics & wiring

Sourcing frame extrusions of proper grade alloy 10 messages

Dec 17, 2023, 3:11 PM Mechanical

Quad Gantry Level travel height to close to bed 25 messages

Dec 16, 2023, 11:54 PM Z Offset First layer First print QGL Configuration

Z endstop/Probe now always triggered - TAP and CAN2209 - RESOLVED 2 messages

Dec 16, 2023, 5:59 PM Configuration

canbus cable causing ripples on prints 4 messages

Dec 16, 2023, 5:41 PM Mechanical

klipper problem 37 messages

Dec 16, 2023, 9:05 AM Configuration

v2.4 extrusion issues 35 messages

Dec 16, 2023, 8:03 AM Mechanical

I’m thinking of self sourcing a voron 2.4 r2, any tips? 15 messages

Dec 15, 2023, 10:18 PM Kits/parts advice

Manta 8p V2 24 messages

Dec 15, 2023, 2:09 AM Initial setup

intermittent inductive probe 2 messages

Dec 14, 2023, 11:06 PM Electronics & wiring QGL

Nevermore macro works while bed fans macro does not 2 messages

Dec 14, 2023, 10:37 PM Configuration

Gantry getting unsquared when tightening A/B belts 3 messages

Dec 14, 2023, 9:37 PM Mechanical Solved

V2.4 all of a sudden print quality in the dumpsters, no layer adhesion etc. 87 messages

Dec 14, 2023, 3:27 AM Mechanical

conflicting stl files 21 messages

Dec 14, 2023, 1:16 AM Kits/parts advice Initial setup

How do I figure out if the fans or my octopus was defunct? 6 messages

Dec 12, 2023, 8:26 PM Solved Electronics & wiring