voron_2_help_forum_public
Required torque on Z-axis motors
Mechanical
Electronics & wiring
Loose belt, fine dust, frayed on top
Mechanical
Finding balance between chamber temp and other settings
Tuning
AB Drive Re-Racks During Belt Installation Even With Everything Tightened
Mechanical
Belt binding issue
Solved
Homing override issues on Kalico
Bed mesh issue
Electronics & wiring
Configuration
Budget toolchanger Voron 2.4 (trident maybe?)
Kits/parts advice
Initial setup
DRV_STATUS: a01f6040 sg_result=64 s2vsb=1(ShortToSupply_B!) stealth=1 cs_actual=31 ola=1 - Shutdowns
Printer shutdown
Electronics & wiring
Voron Tap
Tap
Mechanical
Ldo Nighthawk 36: Connection fails on cold boot
Initial setup
Solved
Electronics & wiring
Configuration
Stepper buzz works but not sensorless homing
Tuning
Initial setup
Solved
Configuration
Weird Z banding on 2.4
Tuning
V2.4R1 to V2.4R2 upgrade guide/video?
Kits/parts advice
350mm z height issues
Mechanical
Can I print the exhaust cover and filament holder in PLA/PLA+?
Kits/parts advice
Solved
switched from CB1 to CM4 and now Klipper wont connect
Solved
Configuration
Replace 1.8 ldo motor with 0.9?
Mechanical
Solved
Extrusion dropped down after tightening z belt
Mechanical
Solved
`BED_MESH_CALIBRATE` is under compensating
Bed mesh issue
Mechanical
First layer
Remove set screws from pully
Mechanical
Solved
Sensorless issues with 5160s now lol
Initial setup
Electronics & wiring
Post for the Pookie :D
Kits/parts advice
What is recommended height for sexbolt?
Mechanical
Solved
wierd CAN errors
Printer shutdown
Solved
Heater extruder not heating at expected rate
Printer shutdown
Electronics & wiring
Back of gantry lower than the front
Mechanical
Solved
config assistance
Initial setup
Configuration
What's happening?
Bed mesh issue
Z Offset
First layer
Solved
QGL
help fixing bed
Bed mesh issue
Mechanical
Please Tell Me Where to Plug This In
Initial setup
Electronics & wiring
Binding on gantry
Tuning
Mechanical
Kits/parts advice
Wierd skipping when doing QGL
QGL
If someone can come on Zoom or discord chat
Electronics & wiring
Kits/parts advice
Mechanical
Initial setup
Solved
V2.4 350MM QGL
Initial setup
Weird pattern while printing after around 500 hours of printing (2.4)
Mechanical
Trouble with gantry level ldo revc 2.4 350 with beacon (revH) i think
Configuration
Troubleshooting First Build, Issues with Toolhead
Initial setup
Electronics & wiring
EBB SB2209 hotend fans wont turn on
Initial setup
Leviathan 1.3 cannot enter DFU mode
Solved
Electronics & wiring
Configuration
What should I replace klicky probe/sexbolt with?
Z Offset
Solved
Bed Heater - Not heating in expected rate - Shutdowns
Printer shutdown
Electronics & wiring
Mains wiring of IEC-GS-1-100 AC Power Entry Module
Electronics & wiring
Toolhead Heatcreep and Skipping
Solved
Used 350mm frame
Mechanical
Not sticking front left
Bed mesh issue
Mechanical
First layer
Crimping Dupont Connectors
Electronics & wiring
PTFE tube in hotend question
Kits/parts advice
Half of top layer is ugly
Bed mesh issue
Z Offset
First layer
Lost communication with the MCU
Printer shutdown
Solved
Vibrations i cant find :/
Mechanical
Kits/parts advice