voron_2_help_forum_public

Thermistor Readings Wrong on Formbot kit 39 messages

Dec 20, 2024, 3:11 AM Solved Electronics & wiring Configuration

Worse temperature fluctuations after PID tune 12 messages

Dec 19, 2024, 6:28 PM Tuning Solved

Z idler screw length 10 messages

Dec 19, 2024, 6:03 PM Mechanical Solved

Voron 2.4 just stop printing for no reason. Maybe CB1 shutdown? 4 messages

Dec 19, 2024, 2:00 PM Electronics & wiring

CB1 does not boot ! 13 messages

Dec 19, 2024, 8:47 AM Solved Electronics & wiring Configuration

X and Y Steppers not behaving 37 messages

Dec 19, 2024, 1:55 AM Mechanical

Z-endstop triggered 4 messages

Dec 18, 2024, 6:58 PM Solved Electronics & wiring

Exstruder issue 32 messages

Dec 18, 2024, 5:06 PM Tuning Solved

Having trouble with full plates 68 messages

Dec 18, 2024, 12:21 AM Tuning

Need some help installing can with bigtreetech SB2209 4 messages

Dec 17, 2024, 7:54 PM Initial setup Solved

Klipper installation and remote access 9 messages

Dec 17, 2024, 7:07 PM Kits/parts advice Initial setup Solved Configuration

Formbot kit Hall Effect Endstop 2 messages

Dec 16, 2024, 11:07 PM Kits/parts advice Initial setup Solved

Voron 2.4r2 Complete rebuild 672 messages

Dec 16, 2024, 11:03 PM Mechanical Solved Electronics & wiring Configuration

Orcaslicer vs Printer.cfg 3 messages

Dec 16, 2024, 4:03 AM Solved Configuration

BTT eddy X Y sensorless homing issues 6 messages

Dec 15, 2024, 10:43 PM Solved Configuration

After the Belt installation of the X Carriage 4 messages

Dec 15, 2024, 8:49 PM Mechanical Kits/parts advice Solved

Help with 1st layer using PLA 8 messages

Dec 15, 2024, 12:43 AM First layer

anyone want to help an amateur out? 17 messages

Dec 15, 2024, 12:01 AM Bed mesh issue Initial setup QGL Configuration

Stealthburner 11 messages

Dec 14, 2024, 4:26 PM Solved Electronics & wiring

BTT PiTFT43 v2.1 Config help 6 messages

Dec 13, 2024, 7:52 PM Solved

blobs 33 messages

Dec 13, 2024, 7:33 PM Tuning Solved Configuration

Neopixel Problem 8 messages

Dec 13, 2024, 4:58 PM Solved Configuration

Calibration Steps 8 messages

Dec 13, 2024, 4:32 PM Solved Configuration

Rapido 2 Heating Slowly 2 messages

Dec 12, 2024, 11:42 PM Mechanical Initial setup Solved Electronics & wiring

Bed_Mesh 14 messages

Dec 12, 2024, 7:26 PM First layer Solved

Testing filament feed 11 messages

Dec 12, 2024, 3:43 AM Initial setup Solved

Flat surface to assemble frame 2 messages

Dec 11, 2024, 9:48 PM Mechanical Kits/parts advice Initial setup Solved

Print stops randomly at any point, usually after few layers but sometimes also randomly 3 messages

Dec 11, 2024, 5:18 PM Mechanical Printer shutdown

The connector on the Rapido V2 thermistor doesn't fit on the SB2209. Does orientation matter? 3 messages

Dec 10, 2024, 7:04 PM Solved Electronics & wiring

klicky Auto Z Really far off 10 messages

Dec 9, 2024, 9:11 PM Electronics & wiring First layer Initial setup Solved Configuration

Octopus MAX EZ 17 messages

Dec 9, 2024, 6:31 PM Initial setup Solved

Strange formbot x rail crunchyness? 32 messages

Dec 9, 2024, 6:08 PM Mechanical Solved

One Z motor not correctly positioned? 3 messages

Dec 9, 2024, 10:29 AM Mechanical Solved

Voron 2.4 (LDO KIT) Randomly Pauses 40 messages

Dec 8, 2024, 11:28 PM Printer shutdown Solved

Z-Stop with kinematic mounts 13 messages

Dec 8, 2024, 9:10 PM Mechanical

Cant get pi camera to work 13 messages

Dec 8, 2024, 5:37 PM Solved Electronics & wiring

Filament Dripping 33 messages

Dec 8, 2024, 1:52 PM Tuning First layer Solved Configuration

Wiring Voron 2.4R Rev C 6 messages

Dec 7, 2024, 8:46 PM Solved Electronics & wiring

v2.4 preinstalling T-nuts 9 messages

Dec 7, 2024, 1:02 AM Mechanical Kits/parts advice Solved

9m tooth idler for the XY Join *Solved* 9 messages

Dec 6, 2024, 8:10 PM Mechanical Initial setup Solved

QGL not equal to the printbed 35 messages

Dec 6, 2024, 6:31 PM Bed mesh issue Mechanical First layer Tap QGL

Smoking when I turn on... 30 messages

Dec 6, 2024, 4:35 PM Solved Electronics & wiring

Crazy second layer 14 messages

Dec 6, 2024, 12:01 PM First layer Solved

Belt Jumping When Moving Back 11 messages

Dec 6, 2024, 4:17 AM Mechanical Solved

Initial checks (stepper buzz) 21 messages

Dec 5, 2024, 3:20 PM Initial setup Solved Configuration

Wrong screw size on page 140? 5 messages

Dec 5, 2024, 3:09 AM Mechanical Kits/parts advice Solved

Budget V0 Build 4 messages

Dec 4, 2024, 7:13 PM Kits/parts advice

Cant connect to moonraker after uninstalling HappyHare 18 messages

Dec 4, 2024, 2:57 PM Solved Configuration

Strange extrusion problem 4 messages

Dec 3, 2024, 8:36 PM Mechanical Solved

rapido heatcreep clog 9 messages

Dec 3, 2024, 4:58 PM Mechanical Solved