voron_2_help_forum_public

Spool drag causing under extrusion? 5 messages

Dec 31, 2024, 3:30 AM Z Offset First layer Solved

Heater Pad Starting To Fall Off 5 messages

Dec 30, 2024, 8:57 PM Kits/parts advice

Pulley and Motion 13 messages

Dec 30, 2024, 8:41 PM Mechanical

z axis dimensional accuracy substantially short 10 messages

Dec 30, 2024, 5:39 PM Tuning Initial setup Solved Configuration

Voron 2.4, klipper. mcu 'mcu': Unable to connect 4 messages

Dec 30, 2024, 1:45 PM Initial setup Solved

very bad first layer 49 messages

Dec 30, 2024, 11:11 AM First layer Solved

Questions on Rapido v2 3 messages

Dec 30, 2024, 3:06 AM Kits/parts advice Initial setup Solved Configuration

X-Endstop bigger than position_max: 350 30 messages

Dec 29, 2024, 9:37 PM Kits/parts advice Mechanical Electronics & wiring Configuration

Hard Layer Shift 20 messages

Dec 29, 2024, 6:15 PM Electronics & wiring Mechanical Kits/parts advice Solved Configuration

Stealthburner issues 13 messages

Dec 29, 2024, 5:16 PM Tuning Mechanical Initial setup Solved Configuration

Incosisted flow? 30 messages

Dec 29, 2024, 3:44 PM Tuning

Stealthburner LED do some wierd glitching. 8 messages

Dec 29, 2024, 1:23 PM Solved Electronics & wiring

bed temperatur offset 17 messages

Dec 29, 2024, 10:15 AM Initial setup Solved

[SOLVED]'probe_name' is undefined BTT Eddy 14 messages

Dec 29, 2024, 6:43 AM Solved Configuration

Voron 2.4 R2 {Formbot} Printed Parts 14 messages

Dec 29, 2024, 3:50 AM Kits/parts advice Solved

SB2209 possibly fried 2 messages

Dec 28, 2024, 8:27 PM Kits/parts advice Solved Electronics & wiring

Voron 2.4 upgrade path for multi head printing. 2 messages

Dec 28, 2024, 7:11 PM Mechanical Solved Configuration

Galileo 2 gear gets very hot 12 messages

Dec 28, 2024, 5:29 PM Mechanical Electronics & wiring

Need advice to choose a good fan - Dragon Hotend HF Voron 2.4R2 3 messages

Dec 28, 2024, 4:39 AM Kits/parts advice Solved

Realistic Print Speeds on Voron 2.4 26 messages

Dec 28, 2024, 3:06 AM Tuning First print Solved Configuration

Cold bed taco + bed mesh being ignored 67 messages

Dec 28, 2024, 12:01 AM Bed mesh issue First layer

cant get my pi camera to work i have a raspberry pi 3 model b v1.2 30 messages

Dec 27, 2024, 11:22 AM Solved Configuration

Leviathan v1.2 not showing up 27 messages

Dec 27, 2024, 1:13 AM Initial setup Solved Electronics & wiring

Screw-in termistor for build plate 9 messages

Dec 26, 2024, 10:13 PM Solved Electronics & wiring

Odd behavior with PT1000, temps flatline 3 messages

Dec 26, 2024, 8:42 PM Initial setup Solved Electronics & wiring

X axis moving in Y direction when homing. Y homes just fine 82 messages

Dec 26, 2024, 7:52 PM Mechanical Initial setup Configuration

3d0 nozzle cam interfering with boot up? 6 messages

Dec 26, 2024, 6:00 PM Initial setup Solved Electronics & wiring Configuration

EBB SB2209 CAN (RP2040) flashing 27 messages

Dec 26, 2024, 4:46 PM Solved Electronics & wiring

Where should the chamber Thermistor be connected to on the BTT M8P Manta? 8 messages

Dec 26, 2024, 2:50 PM Initial setup Solved Electronics & wiring

qgl way over adjusting 113 messages

Dec 25, 2024, 5:47 PM Tuning QGL Tap Solved Configuration

Device "can0" does not exist. 13 messages

Dec 25, 2024, 5:00 PM Initial setup Solved Electronics & wiring Configuration

QGL "Youre Going the Wrong Way!!!" 50 messages

Dec 24, 2024, 11:02 PM Electronics & wiring QGL

Flow Ratio Issue 43 messages

Dec 24, 2024, 4:27 PM Tuning Mechanical First layer Configuration

Extruder temp reads 10C wrong at room temp. 90 messages

Dec 24, 2024, 1:15 PM Solved Electronics & wiring

Additional T-nuts for 300mm build? 5 messages

Dec 23, 2024, 11:03 PM Kits/parts advice Mechanical Solved

MCU 'EBBCan' shutdown: Thermocouple reader fault 15 messages

Dec 23, 2024, 9:14 PM Solved Configuration

X and Y end stops triggered after printing 42 messages

Dec 23, 2024, 4:25 PM Mechanical Solved Electronics & wiring

cant home y axis after printer re-wire 9 messages

Dec 23, 2024, 1:59 AM Mechanical Solved Electronics & wiring

2.4 Hotend Issues after clog, ABS smoking at 240c 14 messages

Dec 22, 2024, 6:07 PM Electronics & wiring

Toolhead LED troubleshooting 25 messages

Dec 22, 2024, 8:50 AM Solved Electronics & wiring

Heat Creep 16 messages

Dec 22, 2024, 1:23 AM Tuning Solved

Printing issues- over extrusion. 37 messages

Dec 21, 2024, 9:05 PM Tuning Mechanical

Magic smoke, but where from? 12 messages

Dec 21, 2024, 8:13 PM Solved Electronics & wiring

MPX-VORON-24R2-KIT 19 messages

Dec 21, 2024, 4:02 PM Kits/parts advice Solved Electronics & wiring

Surface waves 6 messages

Dec 21, 2024, 4:42 AM Tuning

First Layer bad on corners 6 messages

Dec 21, 2024, 3:03 AM First layer

CW2 Clicking 6 messages

Dec 20, 2024, 8:55 PM Mechanical Solved

Toolhead left and right only 5 messages

Dec 20, 2024, 7:50 PM Mechanical Electronics & wiring

Sudden Problems at the same time 8 messages

Dec 20, 2024, 3:04 PM Printer shutdown Solved Electronics & wiring

Extruder temp 5 messages

Dec 20, 2024, 9:36 AM Tap Solved