voron_2_help_forum_public
CB1 WiFi setup issues
Initial setup
Configuration
Heat creep? SB, CW2, Rapido
Tuning
Kits/parts advice
Mechanical
Question about Z End Stop extension for LDO CNC shuttle
Mechanical
Kits/parts advice
Initial setup
Electronics & wiring
Z steppers move back of the gantry down, while testing the X/Y endstop
Mechanical
Initial setup
Solved
Electronics & wiring
If the Y chainrail hits the z belt, how can I correct that?
Tuning
Initial setup
Solved
Workaround?
Mechanical
Solved
Strange issue with petg and part walls
Mechanical
What to check before first power on
Initial setup
Electronics & wiring
I have a problem, but I don't know what to call it.
Mechanical
Initial setup
Solved
Configuration
Voron 2.4 Need help
Configuration
How can I improve my Y-axis acceleration?
Tuning
Mechanical
Used Voron 2.4 Rough Prints
Tuning
Z Offset
First layer
Initial setup
Solved
Am I (my stealthburner) screwed?
Mechanical
Need to reflash my software packages/firmware (I think) and want to make sure I don't miss anything.
Initial setup
Solved
Configuration
Manta M8P + EBB SB2209 (RP2040) can issues.
Electronics & wiring
QGL
Voron 2.4 - Nitehawk 36 MCU Reflash Problems - flashes to stm32f446xx instead of rp2040
Initial setup
Configuration
Trident & Eddy config
Configuration
First Build Gantry Questions LDO v2.4 350
Mechanical
Solved
Tips on buying first Voron 2.4 from Formbot.
Kits/parts advice
Upgrade to Stealthchanger or 2WD Monolith first?
Kits/parts advice
Noises when the gantry moves vertically
Tuning
Mechanical
Solved
Gantry rear too narrow
Kits/parts advice
Mechanical
Initial setup
Solved
LDO V2.4 kit bed ground wire?
Kits/parts advice
Solved
Issue with the printed layer cooling fan after component replacement .
Solved
CAN woes setting up sb2209 and octopus pro v1.0
Initial setup
Configuration
Trying to understand what is happening with my endstops (x, y and z)
Initial setup
Electronics & wiring
Configuration
Help diagnosing main MCU crash (Lost communication with MCU 'mcu') during extruder heating (BTT EBB
Printer shutdown
Initial setup
How square should the Gantry be?
Mechanical
Square frame - are my squares good enough?
Initial setup
XY toothed idler, belt not centering
Mechanical
Large Layer Shifts - Only during printing?
Tuning
Mechanical
Voron 2.4 300mm , Great ,medium and basic. Which to choose.
Kits/parts advice
Frame Question!
Mechanical
Kits/parts advice
How do you guys actually tune speed with everything?
Tuning
Solved
Extrusion issues
Tuning
Mechanical
G2 Extruders (G2E and G2SA) extrusion issues
Mechanical
Initial setup
Issue with building the frame
Initial setup
Solved
Screen not working, after update
Electronics & wiring
Wifi not showing up after restart of printer
Solved
Electronics & wiring
LDO 2.4 rev D seems to be burning Nitehawks like candy
Electronics & wiring
Print End and Cancel tries to move beyond limits
Solved
Configuration
Voron 2.4R2 Doing Layer-Shifting Very Consistently
Mechanical
Solved
Electronics & wiring
Extruder tension weak with tension screw turned all the way in
Mechanical
runout sensor connector
Kits/parts advice
Raspberry pi wont update
Solved
Electronics & wiring
No filament during print job
Mechanical
Solved
Voron 2.4R2 Freezing Solid for NO Apparent Reason...
Printer shutdown
Solved
Electronics & wiring
Extended Dragon Burner fan ducts for ACE hotend?
Mechanical
Kits/parts advice
Formbot voron2.4 software guide?
Kits/parts advice
Initial setup
Configuration
V2.4 350 Z_ENDSTOP_CALIBRATE and offset issues
Z Offset
Initial setup
First print