voron_2_help_forum_public
Cannot get reliable QGL, bed mesh, or z offsets. Plz help
Bed mesh issue
Tuning
Z Offset
First layer
QGL
Reboot on long 30+ hours prints
Mechanical
Configuration
Heated bed not working with Tyson build plate
Mechanical
Belt Tightening: Grinding Noises When Belts are Tensioned
Mechanical
Initial setup
Octopus Pro and CanBus issue
Electronics & wiring
Initial setup
Configuration
QGL not moving to correct X and Y coords after hardware changes
QGL
Nebula Extruder and Nighthawk SB
Kits/parts advice
Electronics & wiring
Bad shaper graphs and belt comparisons, gantry binding issue?
Tuning
Mechanical
Tap
Are these the same shims/washers as instructed?
Kits/parts advice
LDO 2.4 350 revC kit. Recommended updates?
Kits/parts advice
Had a 2.4 for over 5 years, still calibrating it. Rebuild or just get a Bamboo Labs?
Tuning
Mechanical
Configuration
I’m losing my mind trying to print
First print
2.4 shutdowns when the bed is set above 90°C
Printer shutdown
Electronics & wiring
bed mesh problem?
Bed mesh issue
First layer
LDO Voron 2.4 Rev D Pin 'gpio21' is not a valid pin name on mcu 'nhk'
Configuration
voron 2.4 fails pre printing
Tuning
Initial setup
First print
Tap
Configuration
Led flickering
Electronics & wiring
Manually set Z Offset isn't Being Saved
Z Offset
USB stops, CPU overheats, MCU shutsdown After Power Outage
Printer shutdown
Software files
Configuration
First Voron - 2.4 350 Formbot Kit with LDO Doom Cube corner rails - General assembly tips?
Mechanical
Replace Carthographer 3D
Bed mesh issue
Electronics & wiring
Spider V3 USB-to-CAN bridge - MCU "Timer too close" only during rapid TESTZ / PROBE_CALIBRATE
Printer shutdown
Initial setup
Electronics & wiring
Configuration
Voron 2.4 350, leviathan board, ebb sb2209, beacon bed scanner, 0.6 obxidian voron nozzle, help with
Configuration
Deck Panel Sanity Check
Kits/parts advice
ldo rev d kit finish line questions...
Initial setup
Bed flatness
Mechanical
Removing dead Meanwell LRS-200-24 PSU from DIN rail?
Kits/parts advice
Electronics & wiring
Voron 2.4 R2 RevC
Electronics & wiring
motor z2 wont work
Initial setup
Electronics & wiring
Configuration
Electronics and wiring check for my V2.4 + question about frame grounding
Electronics & wiring
V2.4 suddenly stops working mid print
Mechanical
Printer shutdown
Electronics & wiring
V2.4 Heater extruder not heating at expected rate
Electronics & wiring
Voron 2.4 - "Probe samples exceed samples_tolerance" error
QGL
Help with V2.4 gantry racking - 0.55mm in the back, but 0mm in the front
Mechanical
V2.4 - trouble with QGL after moving all electronics to the top
QGL
Toolhead for water cooled Goliath
Kits/parts advice
2.4 making sizzling sounds. Mains power short.
Electronics & wiring
Z offset Issues with Tap
Tuning
Tap
First layer
Software Setup
Initial setup
Unsure of what could cause the belts to make this noise. Formbot 2.4
Mechanical
Thermistor going bad?
Electronics & wiring
spider v2.3 BOOT button to bootloader?
Initial setup
Configuration
What happened to my motors?
Mechanical
Electronics & wiring
Print from USB Stick directly on my Voron with Mini 12864 Screen
Initial setup
First print
Electronics & wiring
Configuration
Unable to read tmc uart 'stepper_z1' register IFCNT
Initial setup
XY positioning error
Mechanical
Initial setup
Time to close errors
Mechanical
Electronics & wiring
New Voron 2.4 350 - First Layer Extrusion is looking inconsistent
Z Offset
Initial setup
First print
First layer
Input Shaper Error
Tuning
Configuration