voron_2_help_forum_public

Formbot Voron 2.4 R2 Pro+ and ChaoticLab Tap V2 2 messages

Nov 30, 2025, 1:28 PM Initial setup

slight Y move on pure X 47 messages

Nov 29, 2025, 10:47 PM Mechanical

problem with QGL seams like during procedure oneztepper is not working (Z0) 8 messages

Nov 29, 2025, 5:12 PM Electronics & wiring Kits/parts advice QGL Configuration

Nitehawk config help 7 messages

Nov 28, 2025, 9:31 PM Tuning

Formbot kit, which experience is required? Which parts should I print? 3 messages

Nov 28, 2025, 10:54 AM Kits/parts advice

getting weird prints 15 messages

Nov 27, 2025, 11:14 PM Mechanical

First 2.4 with or without cartographer 4 messages

Nov 27, 2025, 3:04 PM Kits/parts advice

Manta m8p and cb2 5 messages

Nov 27, 2025, 2:32 PM Electronics & wiring

Incorrect movement in two different printers 6 messages

Nov 27, 2025, 7:49 AM Tuning Mechanical

Terrible print quality after gantry crash 9 messages

Nov 27, 2025, 1:22 AM Tuning Mechanical Configuration

thinking of getting a voron 64 messages

Nov 26, 2025, 8:38 PM Kits/parts advice

Trouble with z offset 9 messages

Nov 25, 2025, 9:07 PM Solved

2.4 LDO AWD issues 5 messages

Nov 25, 2025, 9:04 PM Mechanical Electronics & wiring

Getting over this random bed dive 4 messages

Nov 25, 2025, 7:47 PM Mechanical Initial setup Configuration

Occasional “resistance/skip” in the X axis during start of print job. 13 messages

Nov 25, 2025, 11:41 AM Mechanical Electronics & wiring

Weird screeching sound when moving 6 messages

Nov 25, 2025, 3:33 AM Mechanical

Prints stretched in the diagonal axis 4 messages

Nov 24, 2025, 11:15 PM Mechanical

Hello 35 messages

Nov 24, 2025, 4:47 PM Tuning Tap Mechanical QGL

Can a Chaoticlab CNC Kit replace the Print-it-Forward parts? 11 messages

Nov 24, 2025, 3:44 PM Kits/parts advice

Z chain bottom anchor 2 messages

Nov 24, 2025, 4:30 AM Kits/parts advice

quad gantry level problem 26 messages

Nov 23, 2025, 9:04 PM Mechanical Solved QGL Configuration

wall artefacts 2 messages

Nov 23, 2025, 7:01 PM Tuning

Leviathan setup help 15 messages

Nov 23, 2025, 6:39 PM Configuration

caselight help please 21 messages

Nov 23, 2025, 8:47 AM Initial setup

Electronics Arrangement With Formbot 250 Kit 4 messages

Nov 23, 2025, 5:12 AM Solved Electronics & wiring

heat soak help 66 messages

Nov 21, 2025, 8:24 AM First print Solved

Clogging or something else? 3 messages

Nov 20, 2025, 11:48 PM Mechanical

Voron 2.4r2 extrusion banding. 2 messages

Nov 20, 2025, 8:36 PM Tuning Configuration

BondTech LGX LiteV2 problems 4 messages

Nov 20, 2025, 3:51 PM Tuning Mechanical Configuration

heatbed holes position? 2 messages

Nov 20, 2025, 11:40 AM Mechanical Solved

Formbot 2.4 kit question. 10 messages

Nov 20, 2025, 3:16 AM Kits/parts advice Solved Electronics & wiring

Stealthburner oozing filament 20 messages

Nov 19, 2025, 12:42 PM Tuning Mechanical Configuration

Ballistol grease question 3 messages

Nov 19, 2025, 5:48 AM Kits/parts advice

board not detected after RGB cable touched the extruder motor 39 messages

Nov 18, 2025, 7:13 AM Solved

LDO 42STH48-2504AH 7 messages

Nov 18, 2025, 4:44 AM Mechanical Solved Electronics & wiring

Internal error on command:"QUAD_GANTRY_LEVEL" with Cartographer after adjusting QGL Points. 2 messages

Nov 17, 2025, 4:30 AM QGL

Error: Unable to load module 'motion_queuing' 10 messages

Nov 16, 2025, 4:55 PM Printer shutdown Configuration

thinking of a hotend upgrade from the sb 3 messages

Nov 16, 2025, 2:36 AM Kits/parts advice

Electrical/Software setup 208 messages

Nov 16, 2025, 2:11 AM Initial setup Electronics & wiring Configuration

Belt skipping. 36 messages

Nov 16, 2025, 1:26 AM Tuning

Tool head to high. Dose t reach build plate. 10 messages

Nov 15, 2025, 8:52 PM Mechanical Solved

Top mounting filament out of a dry/storage box 5 messages

Nov 14, 2025, 10:42 PM Kits/parts advice Mechanical

Trying to iron out a squealing gantry issue 9 messages

Nov 14, 2025, 9:40 PM Tuning Mechanical Solved Configuration

Can't figure these layer offset/inconsistencies 5 messages

Nov 13, 2025, 9:49 PM Tuning Solved Configuration

can board with tap. 14 messages

Nov 13, 2025, 3:22 PM Tap

Print Start with OrcaSlicer 20 messages

Nov 12, 2025, 11:30 AM Printer shutdown Initial setup Configuration

TAP Leveling and Stealth Changer 3 messages

Nov 11, 2025, 8:58 PM Kits/parts advice

how to config sb2209 x endstop 37 messages

Nov 10, 2025, 3:42 PM Solved Configuration

can0 show DOWN after every reboot 2 messages

Nov 10, 2025, 2:41 PM Solved Configuration

Smoke on first startup 40 messages

Nov 10, 2025, 2:19 PM Initial setup Solved Electronics & wiring