Got a 5070ti, after installing it I tried updating it to the latest drivers and it black screened so I tried to get through safe mode which I did first try but accidentally restarted after I downloaded ddu. I swapped back to my 3080 which got me to Home Screen allowing me to download the latest drivers from the site for my 5070ti. I went into safe mode to start ddu on my 3080 but now I’m stuck on “set up pin” and when I try to normally boot I just get a black screen
#New drivers…
1 messages · Page 1 of 1 (latest)
i tought i told you about the issues before you got it
You probably did…
good luck
Yea I’m at a loss right now
not much more that can be said or done
Nothing at all?
mhm
Could it be my pcie riser?
If you can get back to windows, you can try all the drivers until 1 works
Or return the 5070ti
Why did you upgrade anyway
3080 being given to sibling
When I figure out how should I use ddu and try to install the latest?
Yeah you can try. They all have their issues and you’ll probably have to try multiple to get one that works
All drivers post-566.36, that is.
50 series was released after that tho so all of their drivers have issues
Yea…
How often does nvidia release new drivers
Because I’m thinking I’ll just run my 3080 until they “fix” it
No idea. I haven’t updated my drivers in quite awhile and I haven’t looked at drivers since
Who knows when that’ll be
It “sends a code” to my outlook but it never receives a code
And I can’t choose a different account
ok i just plugged in my 3080
everything is running fine
Just ran ddu
Should I make it 566
For my 3080 or latest for my 5070
Installed 566 for my 3080
This
so scrap the 5070ti all together...
I went through every driver under the 5070ti
They all black screened
Might just return this 5070ti for a 9070xt
Likely a good idea until nVidia figures their shit out.
Yea it’s bs that I paid $920 for a glorified brick
Same problem here!
OS: Windows 10.0.19045 Build 19045
Motherboard: ASRock B850M Steel Legend WiFi
CPU: AMD Ryzen 9 9900X 12-Core Processor
GPU: NVIDIA GeForce RTX 4070 SUPER (ASUS TUF Gaming GeForce RTX™ 4070 SUPER 12GB GDDR6X OC Edition)
Still using 4070 Super here. Updated to NVIDIA Game Ready Driver 576.28 - got black screen on both monitors shortly after installation finished (1 DP, 1 HDMI), confirmed that windows completely locked up through keyboard behavior.
Restart by power button, no display output in post or in windows on either monitor.
eight power button induced shutdowns later of attempting to enter windows recovery environment, the monitor connected by HDMI turns on, still not recovery environment, but ordinary windows. Good enough.
I roll back to the last driver- 576.02 and restart the computer.
mobo (ASRock Steel Legend B850M) fails to POST, status light indicates GPU failure. I give it ten minutes, no change.
another power-button induced shutdown, proceeds to POST fine with output to hdmi monitor only, boots to windows, still no output to displayport. Great.
After that, I tried to reboot into my other OS, Nobara, but found that the UEFI/BIOS wasn't outputting to either monitor again, so I couldn't select a different boot device (didn't want to perform it blindly.)
Regarding the iGPU and mobo display outputs, They're disabled- I'm running in CSM mode and manually re-entering all my settings after a bios reset would be a pain in the ass. SO, stuck on Windows 10 with my drawing tablet as a monitor and waiting for NVIDIA to push a fixed driver.
Got 576.26-desktop-notebook-win10-win11-64bit-international-dch.hf from NVIDIA Geforce Graphics support, which has fixed the issue.