FO2845 error | 3D Printing | Page 1

wide loom Oct 28, 2025, 7:44 PM

#

Says it’s clogged even though it’s a new extruder assembly on the top half a new nozzle and the filliment is reaching the head at less it should be

surreal drumBOT Oct 28, 2025, 7:44 PM

#

wide loom Says it’s clogged even though it’s a new extruder assembly on the top half a new...

#

AI Help

It sounds like there may be a partial clog in the hotend or nozzle that is obstructing the filament flow. I recommend doing a cold pull or atomic pull to try and clear the clog. If that doesn't work, it may be necessary to disassemble the hotend and clean it thoroughly. Make sure to heat up the hotend before attempting to remove any filament or debris. If you're still having issues, consider reaching out to the manufacturer for further assistance.

wide loom Oct 28, 2025, 7:45 PM

#

New pieces so that’s not possible

craggy wasp Oct 28, 2025, 7:52 PM

#

wide loom New pieces so that’s not possible

What printer is it?

#

Creality or bambu?

wide loom Oct 28, 2025, 7:52 PM

#

Creality k2 plus

#

New nozzle new extruder kit front end

wide loom Oct 28, 2025, 7:54 PM

#

craggy wasp What printer is it?

I’m just extremely lost why it’s throwing a clogged code

craggy wasp Oct 28, 2025, 7:54 PM

#

What happens when u press retry?

wide loom Oct 28, 2025, 7:55 PM

#

Says it’s clogged even though it’s a new nozzle

#

Put a new cutter etc

craggy wasp Oct 28, 2025, 7:56 PM

#

WHat exactly did you install, could u send a pic of the kit?

#

Maybe you didn't wire smth in

wide loom Oct 28, 2025, 7:58 PM

#

There was nothing to wire as I only installed the front end to replace the b Line connected due to teeth breaking it’s the replacement for this

wide loom Oct 28, 2025, 7:59 PM

#

craggy wasp WHat exactly did you install, could u send a pic of the kit?

wide loom Oct 28, 2025, 7:59 PM

#

wide loom

#

The wiring is on the back piece which I didn’t replace due to it being fine

craggy wasp Oct 28, 2025, 8:00 PM

#

have you tried manually pushing the filament through?

wide loom Oct 28, 2025, 8:00 PM

#

craggy wasp have you tried manually pushing the filament through?

That’s my next step

wide loom Oct 28, 2025, 8:01 PM

#

craggy wasp have you tried manually pushing the filament through?

I’m gonna take the cutter out manually feed and if that doesn’t work do a cold pull on top of it

craggy wasp Oct 28, 2025, 8:03 PM

#

no need to remove it

#

just push filament through and pull back on the blue bit while the hotend is at 200

#

or 220

#

just be very careful not to touch it

wide loom Oct 28, 2025, 8:05 PM

#

So heat to 220 then push then pull?

#

Should I remove the cutter incase it’s in the way?

wide loom Oct 28, 2025, 8:33 PM

#

craggy wasp just push filament through and pull back on the blue bit while the hotend is at ...

It was the cutter not connecting to the magnetized strip system correctly, causing a permanent blockage with the blade

#

Or at least that’s what I believe. I’m about to test my hypothesis.

craggy wasp Oct 28, 2025, 8:33 PM

#

wide loom Or at least that’s what I believe. I’m about to test my hypothesis.

Would explain it not detecting anything

wide loom Oct 28, 2025, 8:34 PM

#

Yeah, I was just so confused cause I’ve literally had printers brick on me before and this is just soething that hasn’t happened yet

#

But this also could mean that I need to call priority and have them resend the extrusion assembly due to a part being re-magnetized during transport to the wrong orientation

#

Creality*

#

Yea sums messing up

wide loom Oct 28, 2025, 8:43 PM

#

craggy wasp Would explain it not detecting anything

I don’t know what to do because it’s the cutter. It’s sliding too far every time.

#

@craggy wasp

#FO2845 error