Bambu Labs A1 not printing past a certain height | 3D Printing | Page 1

astral jackal Apr 10, 2025, 2:30 PM

#

I recently have been trying to print a helmet, and the slicer told me this would fit in my print bed, but this happened. I have no idea what to do

devout burrowBOT Apr 10, 2025, 2:30 PM

#

astral jackal I recently have been trying to print a helmet, and the slicer told me this would...

#

AI Help

It appears that the print did not adhere properly to the print bed and shifted during printing. This can happen due to various reasons such as bed leveling issues, improper bed adhesion, or mechanical issues. To troubleshoot, you can try adjusting the bed leveling, ensuring the print bed is clean and using proper adhesive like tape or glue stick. If the issue persists, it might be caused by mechanical problems that need further diagnosis.

spark heart Apr 10, 2025, 2:31 PM

#

It looks like you're damn near the top of the build volume

#

Did the slicer give any warnings?

astral jackal Apr 10, 2025, 2:32 PM

#

it did and I scaled it down and it said it’d be okay. if I have to restart I gotta restart but I wanted to make sure before I waste all this filament lmao

#

just measured i’m supposed to have another inch of build volume left, im so confused

#

I think i’m just gonna bite the bullet and reprint

blissful girder Apr 10, 2025, 3:15 PM

#

astral jackal just measured i’m supposed to have another inch of build volume left, im so conf...

You might need to disable some settings

#

Like y is it even going to the left like that every layer?

astral jackal Apr 10, 2025, 3:15 PM

#

which settings? i’m using the bambulab slicer

#

it’s not it was just paused

blissful girder Apr 10, 2025, 3:16 PM

#

Did u have it paused previously?

astral jackal Apr 10, 2025, 3:16 PM

#

yeah

blissful girder Apr 10, 2025, 3:16 PM

#

The first time it crashed?

astral jackal Apr 10, 2025, 3:16 PM

#

it started happening last night but I was about to go to bed so I just paused it

blissful girder Apr 10, 2025, 3:16 PM

#

Ah

astral jackal Apr 10, 2025, 3:16 PM

#

I wasn’t there when it started happening my roommate saw it tho but idk how

blissful girder Apr 10, 2025, 3:16 PM

#

Yeah idk, prob some setting issue in the slicer

astral jackal Apr 10, 2025, 3:17 PM

#

i’m just gonna cut it into more pieces, I need to find a different model anyway because this one has a lot of bad seams

blissful girder Apr 10, 2025, 3:17 PM

#

Ah yeah then sure

#

Ik on the other Bambu printers you need to remove some parts to use the full build volume

#

Maybe the same thing on the A1?

astral jackal Apr 10, 2025, 3:54 PM

#

oh weird. thank you tho i’ll look into that

blissful girder Apr 10, 2025, 4:14 PM

#

astral jackal oh weird. thank you tho i’ll look into that

In the other printers you need to remove the filament cutter to utilize the full hight (also removes the corner you need to avoid when printing)

astral jackal Apr 10, 2025, 4:15 PM

#

oh thats so weird what the hell. the model new i have is already cut into pieces that snap together so i dont have to worry about it anymore for this project but i will keep that in mind for the future, thank you!!

blissful girder Apr 10, 2025, 4:15 PM

#

Since you technically don’t need it unless u use an ams

#Bambu Labs A1 not printing past a certain height