Need help with spiderman lenses

[final cloak]

So far I printed off the head and the original dimensions of the head are 168.984 x 176.494 x 237.116 mm my dimensions I put to fit my head are 181.7 x 205.334 x 218.812 mm now I can’t get the lenses to the correct size

[tiny harbor]

AI Help

It sounds like you may need to adjust the scaling of the lenses separately in your slicing software to match the new dimensions of the modified head model. Check the scale settings or consider resizing just the lenses before slicing and printing again. Pay attention to the dimensions and ensure they match the intended size for a proper fit.

WARNING: This response is AI generated and may contain errors.

[final cloak]

I’m using the adventure 5m
Ocraslicer

@fresh dove @candid swift

[fresh dove]

@final cloak get the dimensions from the original file

[final cloak]

Of all of it all together including the lenses or spilt the parts and just give the original head size? @fresh dove

[fresh dove]

get that from the resized part

[final cloak]

From the resized part it all says 100 in all three @fresh dove

[fresh dove]

add the model you didnt change and get sizes in mm

[final cloak]

Okay I got the original size mm up @fresh dove

[fresh dove]

share it

[final cloak]

@fresh dove

[fresh dove]

@final cloak like this

[final cloak]

It’s just at 100 nothing has changed from the original model @fresh dove

[fresh dove]

same in mm?

[final cloak]

yea those are the original mm

[fresh dove]

So did you resize it at all then?

[final cloak]

yes i saved the file that i resized to my head

[fresh dove]

So what are the dimensions of that one?

[final cloak]

181.70 x 205.33 x 218.81 mm the scale is still the same as the orginal file just 100

[fresh dove]

alright, change original one to those same dimensions now

What are the %s at?

[fresh dove]

now copy over those %s to the part you were trying to size up earlier

[fresh dove]

do both models include that thing on the right?

[final cloak]

yes now as im looking on it i could print both in one go should i just do that or just go to my separate lenses project and put in the %?

fyi i already got the mask printed

[fresh dove]

yeah but when you printed the mask, did you separate the lens and then resize?

[final cloak]

fuuu yea

[fresh dove]

alright, so, separate them here as well

then resize the lens with the %

im pretty sure its fine either way but im not sure

[final cloak]

okay so should i just say screw it and redo everything?

[fresh dove]

no

[final cloak]

okay

[fresh dove]

mask you already have printed is fine right?

and its dimensions are 181.70 x 205.33 x 218.81?

[final cloak]

yea its a bit big so it aint tight on my head

[fresh dove]

okay so

split up the models

and apply those same dimensions to the new mask

[final cloak]

okay

[fresh dove]

Then take the % values and apply them to the lenses

[final cloak]

okay after that can i delete the mask when i applied the new % since i already got the mask?

[fresh dove]

yes

[final cloak]

okay i applied the % to the lenses

[final cloak]

@fresh dove

[fresh dove]

that should be it

[final cloak]

okay its printing

[tiny harbor]

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

[fresh dove]

@final cloak how did it go

[final cloak]

didnt work sadly

[fresh dove]

Was size the issue?

[final cloak]

Yep

[fresh dove]

🤔

[fresh dove]

Might just be me but here it looks like it might be appropriately sized 🧐

[final cloak]

its not lmao there a big gap on the bottom still i need a refresher on how to do dimensions lol

i downloaded 3d builder to have the eyes pop in place and just move it over to orcaslicer

[fresh dove]

Nice

[final cloak]

yea its being weird the bottom piece is oversized