new to printing with new issues | 3D Printing | Page 1

flat relic Nov 24, 2024, 11:49 AM

#

im useing a elegoo neptune 3 pro and as of recently my prints have been haveing this issue where the texter is all wrong

i have tied leveling the nozzle over and over but nothink changed

if there is any more infomation you need to help please ask i am open to offer any info i can give

cinder forgeBOT Nov 24, 2024, 11:49 AM

#

flat relic im useing a elegoo neptune 3 pro and as of recently my prints have been haveing ...

#

AI Help

It sounds like the issue with your prints may be related to the bed leveling. In addition to leveling the nozzle, you may also want to check the bed itself to ensure it is properly leveled. Make sure the bed is clean and free of any debris that may affect the print quality. Additionally, check the filament for any clogs or issues.

If the problem persists, you may need to calibrate the extruder steps/mm in your printer's settings. You can refer to the printer's manual for instructions on how to do this.

If you need further assistance, feel free to provide more information about the issue or any other details that may help diagnose the problem.

cinder forgeBOT Nov 24, 2024, 1:50 PM

#

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

flat relic Nov 24, 2024, 7:47 PM

#

so keept changeing the hight and nothink

did a full check (extruder steps/mm) en stuff

if anythink its worse now :/ idk anymore

flat relic Nov 24, 2024, 8:22 PM

#

so after some tuning i feel like my extuder keeps stoping (the cog it self dousent stutter or stop) the filiment just douse not come out for a seccend and its ruining my print
any helps?

cinder forgeBOT Nov 24, 2024, 10:25 PM

#

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

flat relic Nov 24, 2024, 10:27 PM

#

...

pallid garden Nov 24, 2024, 11:38 PM

#

Have you tried calibrating your estep?

flat relic Nov 25, 2024, 12:14 AM

#

yep done that changed nothink sadly :/

pallid garden Nov 25, 2024, 12:31 AM

#

Retraction tower?

#

What slicer are you using?

flat relic Nov 25, 2024, 12:41 AM

#

pallid garden Retraction tower?

i could try printing one but donno if that can help mutch as it seems to just be the filiment is not coming out togever

flat relic Nov 25, 2024, 12:41 AM

#

pallid garden What slicer are you using?

cura

pallid garden Nov 25, 2024, 2:04 AM

#

Have you made sure that your printer is mechanically sound? All bolts all belts everything that moves and connects something to something else

#

Check gantry height with two exact same items, place them under gantry against vertical pieces that move in the z axis and make sure both sides are equal

plucky valley Nov 25, 2024, 3:51 AM

#

Does it use a direct bowden tube?

#

sometimes those get burnt up a little bit

#

nvm i googled it

cinder forgeBOT Nov 25, 2024, 5:55 AM

#

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

flat relic Nov 25, 2024, 3:22 PM

#

pallid garden Check gantry height with two exact same items, place them under gantry against v...

checkdd it all and nothink was out the ordinary

flat relic Nov 25, 2024, 3:22 PM

#

plucky valley nvm i googled it

douse it have one?

i order a new nozzle and that will arive tommrow going to try that maby its a nozzle burn out im hopeing...
just seems to not be consistent with printing

#

i did a start of a print hopeung to capture what im on about
it seems to stop and start the filiment witch is what i belive is the issue

cinder forgeBOT Nov 25, 2024, 5:35 PM

#

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

flat relic Nov 25, 2024, 6:38 PM

#

.

pallid garden Nov 25, 2024, 6:55 PM

#

You did not get any bed adhesion at the beginning

#

Have you tried other filaments?

#

Preferably dried

#

Have you cleaned the bed with warm water and dish soap?

#

If you touched the build plate with your hands could be causing issues

flat relic Nov 25, 2024, 8:42 PM

#

pallid garden Have you tried other filaments?

i have used menny drifient filiments even bought new ones (the green one is new)

flat relic Nov 25, 2024, 8:43 PM

#

pallid garden If you touched the build plate with your hands could be causing issues

yep done that too no change

pallid garden Nov 25, 2024, 9:09 PM

#

Might just be a warped bed, know you already missed with offset but it is looking a bit too close sometimes other than that reach out to elegoo support

cinder forgeBOT Nov 25, 2024, 11:10 PM

#

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

flat relic Nov 26, 2024, 2:17 PM

#

pallid garden Might just be a warped bed, know you already missed with offset but it is lookin...

ill play on this for a bit and see what chnages i can make
thank you for the help

any outher segestions anyone has please say

cinder forgeBOT Nov 26, 2024, 4:20 PM

#

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

flat relic Nov 26, 2024, 11:44 PM

#

fixed
so issue was 2 things
one my nozzle was destoryed like was 0.4 and was printing in 0.2 from the ware down

#

rn_image_picker_lib_temp_3486c870-e4e7-489b-8c9b-88816144fbaf.jpg

flat relic Nov 26, 2024, 11:46 PM

#

plucky valley sometimes those get burnt up a little bit

2ed issue you got oh the head it was burnt
coped that bit off as it was only a little

do i need to get a replament or will it be fine?

Messenger_creation_22D1AA45-27B5-4EB8-843E-0B0319CF9AC8.png

#

outher then that
thank you guys for the help

plucky valley Nov 27, 2024, 12:06 AM

#

flat relic 2ed issue you got oh the head it was burnt coped that bit off as it was only a l...

Just snip the burnt part off with a sharp razor or a bowden cutter if your printer came with one

#

Id get a section of bowden tube online just to be safe but its not necessary right now

#

Or you could flip it around i believe

#

wait for input from other peeps though im newer to this

flat relic Nov 27, 2024, 12:22 AM

#

its all in and running thr now
i immagen it will be fine lol

as for the tube
what key words am i searching to buy them?
auso is the size somethjnk that needs to be exact?

cinder forgeBOT Nov 27, 2024, 2:26 AM

#

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

gentle verge Nov 27, 2024, 2:36 AM

#

flat relic its all in and running thr now i immagen it will be fine lol as for the tube ...

https://us.elegoo.com/products/ptfe-tube?variant=43734172139701

moore than likely, you'll be loooking at thas. I found it buy locking up the pronter moodal

ITEM MODEL
search "PTFE tube elegoo neptune 3 pro"

ELEGOO US

PTFE Tube

ELEGOO specializes in the research, development, and production of the most quality & affordable 3D printers, Arduino-based STEM & robotic kits, making technology easy-to-access for all the makers around the world.

#new to printing with new issues