nocturne jay
I have a stock SV06 and use prusaslicer.
As you can see in the image, all the organic supports broke which is also what caused that stringy mesh. On top of that I also got a layer shift and have no idea if the two are related. Any help is much appreciated because I am losing my shit over this. It printed another thing perfectly fine yesterday and this morning I came back to this gobshite after letting it run overnight.
desert violetBOT
I have a stock SV06 and use prusaslicer.
As you can see in the image, all the or...
nocturne jay
oh yeah im printing with 3djake ecopla at 220/60C and the fan runs at 100% permanently
desert violetBOT
nocturne jay
help?
desert violetBOT
nocturne jay
.
wary pivot
Is your nozzle clean? check that.
nocturne jay
Is your nozzle clean? check that.
I cleaned it just before firing it up again because it sat for a while
I also tightened the belts again so I'm wondering how it shifted
nocturne jay
.
jagged jewel
I also tightened the belts again so I'm wondering how it shifted
how tight did you get them? and delete that image, no printing of that kind acording to mods, or mark it as prop if it is one
nocturne jay
how tight did you get them? and delete that image, no printing of that kind acor...
They were quite loose so clearly not tight enough, I could've sworn I tightened them more though
But now I'm stuck on what caused every last support strut to break
jagged jewel
They were quite loose so clearly not tight enough, I could've sworn I tightened ...
im guessing a combo of the layershift pulling on them harder than normal, and the support first layer density being low
nocturne jay
im guessing a combo of the layershift pulling on them harder than normal, and th...
don't see any option for that
all i see is related to that is this
nocturne jay
guess im fucking blind then 💀
its at 90 but i'll try 100
triple check the belts and then i'll give it another go
jagged jewel
i think the supporst failing was mainly the layer shift, but 
nocturne jay
if this shit doesnt work now i am going to burn my house down out of spite this place is cursed, any printer that enters these walls fails miserably
jagged jewel
?belt_freq 0.22
desert violetBOT
jagged jewel
should be around that pitch
nocturne jay
i think the supporst failing was mainly the layer shift, but <:shrugs:2408136044...
the stringy mess around the trigger area is supposed to be support, it failed way before the layer shift resulting in that hot mess
jagged jewel
hard to tell, was the z offset good? i brought up the support density part because there was a section that just wasnt filled in, but it could have been z offset as well
nocturne jay
hard to tell, was the z offset good? i brought up the support density part becau...
yes, i checked it and leveled the bed and used adhesive spray for this print to make sure nothing could happen 💀
jagged jewel
picture of a first layer? z offset being right >adhesives
nocturne jay
picture of a first layer? z offset being right >adhesives
don't have a picture but it looked good to me, im not new just a bit rusty. when i try again in 10 minutes or so i'll send a pic
nocturne jay
@jagged jewel it was underextruding slightly, I corrected that. Could that cause the supports to fail?
Can't get a picture because it's too dark
jagged jewel
i mean its possible, but general underxtrusion is such a blanket term that it doesnt really point me to any peticular reason
desert violetBOT
nocturne jay
now it just shreds the filament within seconds of print start
it doesnt matter at all if i have loads of tension or nearly nothing, it just grinds through the filament sooner or later. farthest i have gotten now is layer six after that one print with the layer shift in the picture
could it simply be too old? it was stored in a vacuum sealed bag with silica for 2 years now
but if 2 years is the limit on usability i'd be surprised
