OctoPi on new Pi ignores custom gcode (from file) | 3D Printing | Page 1

umbral skiffBOT Jul 12, 2024, 12:27 AM

#

AI Help

It seems like your custom start G-code is not heating up the nozzle properly. In OctoPrint, the placeholders for temperature settings can vary depending on your printer profile. You should ensure that "{material_print_temperature}" is the correct placeholder for nozzle temperature in your case.

To troubleshoot this issue, you can:

Confirm the correct placeholder for nozzle temperature in your printer profile settings within OctoPrint.
Verify that the G-code script is correctly configured to set and wait for the nozzle temperature to reach the desired level before starting the print.
Double-check that the G-code commands are compatible with your Ender 3 v2 and Marlin firmware version.

If everything appears to be set up correctly, it might be beneficial to check for any specific plugins related to temperature control that could be affecting the heating process. You may want to review the OctoPrint logs for any error messages related to temperature control.

umbral skiffBOT Jul 12, 2024, 2:28 AM

#

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

ashen gulch Jul 12, 2024, 3:03 PM

#

issue still present

umbral skiffBOT Jul 12, 2024, 5:08 PM

#

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

ashen gulch Jul 12, 2024, 5:09 PM

#

a

ashen gulch Jul 12, 2024, 5:34 PM

#

ok it is heating up the hotend now but still ignores the bed leveling part of the gcode

fluid flume Jul 12, 2024, 5:44 PM

#

ashen gulch ok it is heating up the hotend now but still ignores the bed leveling part of th...

why are you using octoprint start gcode? why not slicer

#

and are you sure you are using UBL? M420 S1 is garuenteed to load the mesh

ashen gulch Jul 12, 2024, 5:49 PM

#

it is in the slicers custom gcode (cura) and yes I am using UBL

#

i tried it before with it in octoprint but it was always in the sliced file, the only thing that changed in my set up is the new Pi and fresh install of octoprint.

umbral skiffBOT Jul 12, 2024, 7:53 PM

#

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

ashen gulch Jul 12, 2024, 7:54 PM

#

a

umbral skiffBOT Jul 12, 2024, 9:55 PM

#

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

ashen gulch Jul 13, 2024, 2:08 PM

#

ok its bed leveling but heating the hotend before instead of after

umbral skiffBOT Jul 13, 2024, 4:10 PM

#

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

ashen gulch Jul 13, 2024, 4:11 PM

#

a

umbral skiffBOT Jul 13, 2024, 6:15 PM

#

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

ashen gulch Jul 13, 2024, 6:16 PM

#

a

ashen gulch Jul 13, 2024, 7:16 PM

#

a

umbral skiffBOT Jul 13, 2024, 9:20 PM

#

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

ashen gulch Jul 13, 2024, 9:28 PM

#

a

umbral skiffBOT Jul 13, 2024, 11:30 PM

#

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

ashen gulch Jul 14, 2024, 12:41 AM

#

a

umbral skiffBOT Jul 14, 2024, 2:45 AM

#

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

ashen gulch Jul 14, 2024, 2:46 AM

#

a

umbral skiffBOT Jul 14, 2024, 4:50 AM

#

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

ashen gulch Jul 14, 2024, 1:20 PM

#

a

ashen gulch Jul 14, 2024, 2:19 PM

#

#OctoPi on new Pi ignores custom gcode (from file)