#Klipper Install Laptop + Ender Neo max

1 messages · Page 1 of 1 (latest)

zinc rose
#

MCU Unable to connect + using URACL

Not sure if the firmware is installed it just shows CREALITY
#software

icy saddleBOT
#
AI Help

It appears that you are experiencing issues with connecting your 3D printer to your computer using Unified Remote Access Control and are unsure about the firmware status. To troubleshoot this, I recommend first checking if the firmware is up to date and properly installed on your 3D printer. You can visit the manufacturer's website for instructions on how to do this. Additionally, ensure that the connection settings in URACL are correctly configured. If the issue persists, you may also want to check for any compatibility issues between your 3D printer and the software being used. If you need further assistance, please provide more details about your setup.

WARNING: This response is AI generated and may contain errors.
zinc rose
carmine horizon
# zinc rose

I'm gonna assume you put the klipper .bin file into sd card

#

And plugged it into printer

zinc rose
#

Yes

carmine horizon
#

Turned off printer

#

Turned on again

zinc rose
#

Yes

carmine horizon
#

And it blank screened or similar

zinc rose
#

I tried doing it off then on and on then off

#

This is what I see

#

There’s no controls whatsoever th

#

Tho

low thorn
#

It's the same if you use a pi or a laptop

zinc rose
#

Oh okay

#

I don’t see anything when I do that command you said though

low thorn
#

Oh I didn't type it out exactly correct

carmine horizon
# zinc rose There’s no controls whatsoever th

https://youtu.be/_8r87gBFOy8?si=lLd9LLRlahru7H6y 13:11

YouTube
Foul News
Install Klipper On Your Ender 3 V2 Neo Fast! - COMPLETE GUIDE

This is a very detailed overview on how to quickly install Klipper on your Creality Ender 3 V2 Neo. This guide is perfect for beginners that don't want to read through hours worth of documentation or watch videos that might not show everything you need to do in order to get Klipper installed. This guide also works for any Creality printer, as lo...

▶ Play video
low thorn
#

Just tab to auto complete

carmine horizon
#

Don't know enough about Enders to confirm this

#

But I don't see how it would

low thorn
zinc rose
#

But when I do that command it says there’s no file directory

#

So what’s up with that?

low thorn
carmine horizon
#

Means it can't find printer more than likely

#

Show screenshot regardless

zinc rose
#

I’m connected by USb to USb-C

#

From the laptop to Printer

low thorn
#

Do lsusb and take a pic

zinc rose
low thorn
#

Looks like it's not even connected

carmine horizon
#

Might be power only cable

zinc rose
#

I’ll try a different cable

zinc rose
#

And do I got to get it out and rename it

#

Or do I simply just turn it off and disconnect the screen and put the SD card back

zinc rose
#

I tried a new USB

#

Maybe it recognizes it?

#

But the serial command still doesn’t work

low thorn
#

Still doesn't look like it's connected

zinc rose
#

How’s it supposed to look like

#

?

carmine horizon
#

I have a feeling it didn't flash correctly

#

Keep power cycling it a few times

#

With sd card in

#

And see if any changes happen

zinc rose
#

It adds serial converter

#

Whenever I add the USB

zinc rose
carmine horizon
#

Although a ch340 is an esp32 chip irrc

#

Nvm

#

Some 3dp motherboards use it to

#

Have you tried doing ls /dev/serial/by-id

zinc rose
#

Is that supposed to work w proper flashing and without

#

Cuz I can’t see anything

#

It can’t find directory or nothing

#

@carmine horizon

zinc rose
#

Either that or for some reason I can’t access the serial directory

#

It simply doesn’t exist

#

for some reason