#Filament clustering on nozzle

1 messages · Page 1 of 1 (latest)

cerulean dagger
#

It is leveled, and everything. I just changed the speed in orcaslicer. Maybe its not extruding fast enough? I am not sure.

printer: adventurer 3

kind impBOT
#
AI Help

It sounds like the issue you are experiencing could be related to the extrusion speed setting in OrcaSlicer. Try checking the extrusion multiplier or flow rate settings to ensure that the filament is being extruded at the correct speed. You may need to adjust these settings to increase the extrusion rate if the print is coming out too slowly. Additionally, make sure that the nozzle is not clogged and the filament is loaded properly. If the issue persists, you may need to further troubleshoot the extruder mechanism itself.

WARNING: This response is AI generated and may contain errors.
cerulean dagger
#

#✅｜help-quick-questions message

kind impBOT
# cerulean dagger

https://www.wevolver.com/article/z-offset-what-it-is-and-how-to-adjust-it

TLDR:

Setting your z-offset correctly ensures a good first layer squish and proper adhesion to the build plate (assuming its clean, see
?bedcleaning for more information). See
?leveling for a good representation of how the first layer should look like.
If in doubt: Refer to you your specific machines documentation.

For the Qidi X series printers: Adjusting the z offset from the Fluidd webinterface breaks it. Always set the z offset from the printers screen.

?z-offset requested by: m.von.d#0
cerulean dagger
#

leveling is fine already

#

flashprint works fine. unlike orcaslicer

chilly coral
#

You compared all settings?

cerulean dagger
#

everything else is the same i think but im new to orcaslicer

chilly coral
cerulean dagger
chilly coral
#

Thats slow

cerulean dagger
#

it needs to be way thicker than that, so it wont stick to the plate

chilly coral
cerulean dagger
#

just caused more problems

chilly coral
cerulean dagger
#

adventurer 3 problems

cerulean dagger
#

first layer is the same as flashprint settings

chilly coral
#

Yeah sounds like it. Got the start gcode set up the same?

cerulean dagger
#

i dont think flashprint gives you that info

#

yeah it doesnt

cerulean dagger
#

been trying this bs since 8am

chilly coral
#

Flashforge are the worst

cerulean dagger
#

now its 10:44

cerulean dagger
#

but its gonna be a while bc $500

#

hoping it doesnt get out of stock on amazon 😭

chilly coral
#

Theres apparently a way to read the .gx files that flashprint spits out. You could try getting the start gcode from there

cerulean dagger
#

if youre able to extract it, 🤷‍♂️

#

maybe i have the wrong one set?

image.png
chilly coral
# 
;machine_type: Adventurer 3 Series
;right_extruder_material: PLA
;right_extruder_material_density: 1.24
;filament_diameter0: 1.75
;right_extruder_temperature: 210
;layer_height: 0.18
;perimeter_shells: 2
;top_solid_layers: 4
;bottom_solid_layers: 3
;fill_density: 15%
;fill_pattern: hexagon
;base_print_speed: 60
;travel_speed: 80
;platform_temperature: 50
;right_extruder_temperature_raft0: 215
;right_extruder_temperature_reset: 
;left_extruder_temperature_reset: 
;layer_total_count: 449
;start gcode
M118 X26.94 Y52.60 Z81.65 T0
M140 S50 T0
M104 S215 T0
M104 S0 T1
M107
M900 K0.000 T0
G90
G28
M132 X Y Z A B
G1 Z50.000 F420
G161 X Y F3300
M7 T0
M6 T0
M651 S255
;layer_count: 449
M108 T0
G1 X-26.60 Y21.78 F4800
;preExtrude:0.20
M106
G1 Z0.200 F420
;structure:pre-extrude
G1 X-26.60 Y21.78 F4800
G1 X-26.60 Y-46.11 E9.8450 F1200
G1 X-26.35 Y-47.85 E10.0999
G1 X-25.58 Y-49.55 E10.3706
G1 X-24.37 Y-50.97 E10.6411
G1 X-22.81 Y-51.99 E10.9114
G1 X-21.07 Y-52.52 E11.1752
G1 X-20.06 Y-52.60 E11.3221
G1 X20.11 Y-52.60 E17.1473
G1 X21.85 Y-52.35 E17.4022
;raft
;layer:0.40
;support-start
G1 E12.4022 F1500```
#

Well

#

Just rename as .txt

cerulean dagger
#

at all 🤣

chilly coral
#

Just compare the start gcode sections or better yet post the orcaslicer one

cerulean dagger
#

end g code:

# 
M104 S0 T0
M140 S0 T0
G162 Z F1800
G28 X Y
M132 X Y A B
M652
G91
M18
cerulean dagger
cerulean dagger
chilly coral
#

yeah that should not matter

cerulean dagger
chilly coral
#

Not really, sorry.

cerulean dagger
#

damn

cerulean dagger
#

man wth is this

image.png
chilly coral
#

I would try the tried and true trifecta of bedcleaning, releveling, zoffset

cerulean dagger
chilly coral
#

Ideally you calibrate that

cerulean dagger
#

aka how fast it pushes out filament

#

etc

chilly coral
#

That is the exteusion speed

#

Its the factor to calculate how much filament is transported how fast

cerulean dagger
#

what would that be on orcaslicer

chilly coral
#

speed at which the filament is pushed after a retraction

cerulean dagger
#

how do i calculate

chilly coral
cerulean dagger
#

Make some money off of it 💀

cerulean dagger
#

Extrudes way more filament than orcaslicer

chilly coral
#

In orca

cerulean dagger
#

Alr

kind impBOT
#
This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

cerulean dagger
#

i cant find it

#

?solve

kind impBOT
cerulean dagger
#

wha

#

?help

kind impBOT
# 
BenchyBot

BetaCommands:
  add_printer  Adds a printer to your name.
  belt_freq    Calculates target belt frequency (Hz) for correct tension base...
  belt_tension Calculates the tension (N) in a GT belt based on the measured...
  pi           
  random_thing Find a random thing from thingiverse.
  time         Used to get the current time in a timezone.
  topic        
GCode:
  mg           Used to search Marlin Gcode Commands.
HelpForum:
  solved       
​No Category:
  help         Shows this message

Type ?help command for more info on a command.
You can also type ?help category for more info on a category.
cerulean dagger
#

?solved