Help pls | 3D Printing | Page 1

next mural Apr 26, 2024, 3:36 AM

#

I think that my nozzle might be clogged or something because nothing goes through it at all, even if i try to push hard through it. I did notice that on the silicone sock surrounding the nozzle was some filament. Can there be something wrong with the extruder and I have to replace it or something?

lavish orbitBOT Apr 26, 2024, 3:36 AM

#

next mural I think that my nozzle might be clogged or something because nothing goes throug...

#

AI Help

It sounds like you may have a clogged nozzle. It's common for filament to get stuck in the nozzle and cause blockages. You can try cleaning the nozzle using a nozzle cleaning needle or a cold pull method to remove any blockages. If that doesn't work, you may need to replace the nozzle. Check the extruder gear as well to make sure it's not clogged or worn out. If the problem persists, it's best to seek further assistance or consider replacing the entire extruder assembly.

bitter stratus Apr 26, 2024, 3:37 AM

#

I would honestly say try to replace your nozzle, when you do that it usually knocks out that filament, thats my experience tho

molten wing Apr 26, 2024, 3:37 AM

#

Post a picture and remove the sock

next mural Apr 26, 2024, 3:37 AM

#

Oh ok, mind recommending me any nozzles?

#

Ok

molten wing Apr 26, 2024, 3:38 AM

#

You might have a clog

#

?coldpull

lavish orbitBOT Apr 26, 2024, 3:38 AM

#

https://youtu.be/MGt8cnVIKW8

YouTube

3D Printing Nerd

3D Printing 101: How To Fix a Clogged Nozzle Using a Cold Pull!

Clearing a jam in the nozzle can be an easy fix. Using nylon filament and a few minutes of your time, you can clear the debris within your nozzle that causes inconsistent extrusions and failed prints!

Ultimaker 2 and 2+ 3d printer custom face plate by A Pyro Design: https://etsy.me/2P8FPyJ

Ultimaker enclosure by Printed Solid:
https://www.prin...

▶ Play video

next mural Apr 26, 2024, 3:38 AM

#

i already tried cold pull and sitcking a needle and everything, filament just does not go through at all

bitter stratus Apr 26, 2024, 3:39 AM

#

My ender 3 v2 came with a couple spare nozzles, so I don't really have a recommendation

next mural Apr 26, 2024, 3:39 AM

#

I got the same one, got it second hand with a bunch of upgrades

#

#

I'll just replace a nozzle, found one

molten wing Apr 26, 2024, 3:50 AM

#

Looks not to bad, at least no leak

next mural Apr 26, 2024, 3:59 AM

#

i took off the nozzle and there might be filament on the inside? idk

#

let me take a pic

#

#

is that filament on the inside? I was using red filament before it clogged

molten wing Apr 26, 2024, 4:06 AM

#

Is your bowden tube red?

next mural Apr 26, 2024, 4:24 AM

#

uh idk

#

the thing coming out is blue

molten wing Apr 26, 2024, 4:29 AM

#

Then its your filament😁

next mural Apr 26, 2024, 4:29 AM

#

O

#

imma heat it up and then just take it out ig

#

thanks for letting me know

#

Im knew to this thing lol

next mural Apr 26, 2024, 6:11 AM

#

Huh, i cleaned it out and all butnothing comes out anyway

#

Should i just go back to the stock? or how can i try to open it to fix the problem

#

It might be the pfte actually

#

took it out and still the same, cant put anything through the nozzl

molten wing Apr 26, 2024, 6:37 AM

#

next mural took it out and still the same, cant put anything through the nozzl

take a look at the extruder it might be stuck in there somehow

#Help pls