ender 3 v3 ke | 3D Printing | Page 1

chilly skiff Jan 23, 2024, 11:41 AM

#

Hello guys im trying to print abs im newbie and ichoose abs in the crealitt app but when i try to print these even in the first layer a problem coming what should i do

violet nebulaBOT Jan 23, 2024, 11:41 AM

#

chilly skiff Hello guys im trying to print abs im newbie and ichoose abs in the crealitt app ...

#

AI Help

If you are encountering issues while printing ABS, here are a few troubleshooting tips:

Ensure your printer's bed is properly leveled: Improper bed leveling can lead to issues with the first layer. Check your printer's manual for instructions on how to level the print bed correctly.
Use a heated bed: ABS typically requires a heated bed to prevent warping and promote bed adhesion. Set the bed temperature to around 90-100°C.
Apply an adhesive: To improve bed adhesion, you can apply a layer of adhesive such as hairspray, glue stick, or ABS slurry to the print bed before starting the print. This helps the print stick to the bed more securely.
Adjust the nozzle height: Verify that the nozzle is close enough to the print bed to ensure proper adhesion. The recommended nozzle gap is usually around 0.1-0.2mm.
Optimize the first layer settings: Adjust your slicing software's settings to ensure a good first layer. Set a slower print speed for the initial layer, increase the...

topaz beacon Jan 23, 2024, 11:42 AM

#

chilly skiff Hello guys im trying to print abs im newbie and ichoose abs in the crealitt app ...

ABS is challenging to print without an enclosure because it warps way, way more than PLA or PETG

#

to print ABS effectively you need to have an environment with no air drafts

chilly skiff Jan 23, 2024, 11:42 AM

#

Ohhhhh

#

But my windows are not open

topaz beacon Jan 23, 2024, 11:43 AM

#

If I were you, I would buy PLA or PETG instead if your needs don't specifically require ABS

#

Try enabling adhesion or a brim in the slicer

chilly skiff Jan 23, 2024, 11:43 AM

#

But someof my needs needs abs

chilly skiff Jan 23, 2024, 11:44 AM

#

topaz beacon Try enabling adhesion or a brim in the slicer

How can i do it

topaz beacon Jan 23, 2024, 11:44 AM

#

what slicer

chilly skiff Jan 23, 2024, 11:44 AM

#

Creality

topaz beacon Jan 23, 2024, 11:44 AM

#

enable adhesion on the top right in print settings

chilly skiff Jan 23, 2024, 11:44 AM

#

Or should i make the nozzle more heated

topaz beacon Jan 23, 2024, 11:44 AM

#

what temps are you using

chilly skiff Jan 23, 2024, 11:45 AM

#

#

İn the top right corner idont see anything

#

And thanks for everythinf

topaz beacon Jan 23, 2024, 11:46 AM

#

search for brim

#

does you print have supports?

chilly skiff Jan 23, 2024, 11:46 AM

#

100mm s

#

Brim

chilly skiff Jan 23, 2024, 11:48 AM

#

topaz beacon does you print have supports?

No

#

topaz beacon Jan 23, 2024, 11:48 AM

#

it 100% requires supports

#

you have floating objects

chilly skiff Jan 23, 2024, 11:49 AM

#

Ohhh

#

Thats why is it making

#

Problems?

topaz beacon Jan 23, 2024, 11:49 AM

#

also try printing one at a time

chilly skiff Jan 23, 2024, 11:49 AM

#

In the app

#

It said something before printing

#

Like you should put supports

topaz beacon Jan 23, 2024, 11:49 AM

#

yes

chilly skiff Jan 23, 2024, 11:49 AM

#

Yes they are floating

#

Ican see it

#

topaz beacon Jan 23, 2024, 11:50 AM

#

the part on the top left looks like it has very tight tolerances, so you should definitely print that by itself

chilly skiff Jan 23, 2024, 11:51 AM

#

Okay

#

Iwill print it itsswlf

#

Also how can i put support to printing bed

#

To not make it float

#ender 3 v3 ke