Klipper Installation Not Working Properly

[frosty dust]

Moved from general

[bronze grotto]

AI Help

Sure, I'll be happy to answer your questions about 3D printing. What would you like to know?

WARNING: This response is AI generated and may contain errors.

[frosty dust]

so

Hello?

[winged birch]

did you follow a guide or anything?

[frosty dust]

yes.

https://www.youtube.com/watch?v=_8r87gBFOy8&t=235s\

except i used my own printer.cfg from online etc

[winged birch]

did you try renaming the klipper.bin to firmware.bin?

[frosty dust]

yep

[winged birch]

try running curl -sSL https://raw.githubusercontent.com/mainsail-crew/MainsailOS/develop/patches/udev-fix.sh | bash, mainsailOS had a bug in it about this at one point

[frosty dust]

in this?

[winged birch]

yeah

[frosty dust]

ok

wait how do i ctrl v again

[frosty dust]

it just shows ^V

[winged birch]

right click the header and paste from there

[frosty dust]

working

it says reebot

[winged birch]

shutdown -r now

[frosty dust]

how do i turn it on

or is that auto

[winged birch]

thats a reboot, auto

[frosty dust]

alrighty

he takes a while

its on again

same issue

[winged birch]

run the ls again, and just to make sure, printer is on and connected when you run it?

[frosty dust]

mhm

ugh

[main mural]

what serial did you have at the printer.cfg?

[frosty dust]

# V3 SE. To use this config, during "make menuconfig" select the
# STM32F103 with a "28KiB bootloader" and serial (on USART1 PA10/PA9)
# communication.

# If you prefer a direct serial connection, in "make menuconfig"
# select "Enable extra low-level configuration options" and select
# serial (on USART3 PB11/PB10), which is broken out on the 10 pin IDC
# cable used for the LCD module as follows:
# 3: Tx, 4: Rx, 9: GND, 10: VCC

# Flash this firmware by copying "out/klipper.bin" to a SD card and
# turning on the printer with the card inserted. The firmware
# filename must end in ".bin" and must not match the last filename
# that was flashed.

# This also works for the GD32F303 based Creality 4.2.2 board.

# See docs/Config_Reference.md for a description of parameters.```

USTART3 PB11/PB10

[main mural]

And whats the port you gave it ?

[frosty dust]

22

[main mural]

in the cfg?

[frosty dust]

oh in cfg

[main mural]

yeap

[frosty dust]

0

[main mural]

seems good

[frosty dust]

see

idk whats wrong

[main mural]

what does the klippy log says?

[frosty dust]

supposed to say this:

[main mural]

just to make sure

at what point of the procedure are you?

[frosty dust]

https://youtu.be/_8r87gBFOy8?t=844

that exact time frame

[main mural]

so you can access fluid right?

or mainsail sorry

[frosty dust]

yeah

[main mural]

can you download the klipper log?

and send it here?

[frosty dust]

where is that located

[frosty dust]

yep. mb

[main mural]

it says Unable to open config file /home/pi/printer_data/config/printer.cfg

[frosty dust]

why in teh world

[main mural]

not sure

can you send the config file same way?

[frosty dust]

its there

[main mural]

Can you add : [include mainsail.cfg]

at the top of the printer.cfg ?

over [sterpper_x]

restart and down load the log file again and send it here

[main mural]

give me a sec

Ok so

Use this serial : on USART1 PA10/PA9

not the one you using right now

[frosty dust]

oh

why

i ran the shutdown command and now my damn pi wont turn on again

[main mural]

pb11/pb10 here should change to USART1 PA10/PA9

plug and unplug?

give it some time to connect

is it wireless or cable?

[frosty dust]

wireless

its up again

do i also add the new klipper.bin

[main mural]

did you changed back to on USART1 PA10/PA9?

[frosty dust]

yo where did it go

it isnt saving

[frosty dust]

yeah

why is it a .config

yo what the hell

[main mural]

did you typed Q the Y for yes

[frosty dust]

yeah

[main mural]

and make ?

[frosty dust]

OH MAKE

[main mural]

Yeap 😛

[frosty dust]

why

its a hex

[main mural]

So when you reflash the bin file you have to change the name that it previously was

[frosty dust]

i will but its not a bin anymore

its a hex

[main mural]

hm

you have a 32bit board right?

not 8 bit?

[frosty dust]

ye

[main mural]

can you also send a screen shot of the setup menu before you hit quit and yes?

[frosty dust]

do you want to get into a call

[main mural]

your bootloader should be : 28KiB bootloader

not 8kib

try changing that too and then compile

We can yes. not sure if I can be more of a help there though 😛

[frosty dust]

alr its made

firmware.bin or keep it as klipper.bin

[main mural]

what is the current bin name you have flashed ?

if it was klipper rename to firmware

[frosty dust]

idk it was klipper but then changed it to firmware

both worked

[main mural]

can you join in the voice channel?

curl -sSL https://raw.githubusercontent.com/mainsail-crew/MainsailOS/develop/patches/udev-fix.sh | bash
sudo reboot

ls /dev/serial/by-id/*

systemctl restart klipper

[frosty dust]

https://github.com/0xD34D/ender3-v3-se-klipper-config/tree/main