initial Klipper setup on a v2.4 | 3D Printing | Page 1

small karma Sep 17, 2023, 10:11 AM

#

in initial setup, yesterday i flashed the pi and could connect with it, then i flashed the octopus and couldnt connect anymore, now, i reflashed the pi and still cant connect, always conncetced via ethernet
not even appearing in router now

tulip pikeBOT Sep 17, 2023, 10:11 AM

#

small karma in initial setup, yesterday i flashed the pi and could connect with it, then i ...

#

AI Help

It seems like you are having trouble connecting to your Raspberry Pi after flashing it. Here are a few troubleshooting steps you can try:

Double-check the router settings: Make sure that your router is not blocking any connections from the Raspberry Pi. Check the router's manual or configuration settings for any potential issues.
Verify the Ethernet connection: Ensure that the Ethernet cable is securely connected to both the Raspberry Pi and the router. Try using a different cable or port on the router to see if that solves the issue.
Check the power supply: Make sure that the power supply for the Raspberry Pi is providing enough power. Insufficient power supply can cause connectivity problems. Try using a different power supply if available.
Re-flash the Octopus: If you suspect that the issue is related to flashing the Octopus, try re-flashing it following the proper instructions. Make sure to use the correct software and firmware versions for your setup.
Verify...

small karma Sep 17, 2023, 10:34 AM

#

with a btt pi btw

small karma Sep 17, 2023, 11:18 AM

#

here it is lol @stuck bridge

stuck bridge Sep 17, 2023, 11:18 AM

#

what psu

small karma Sep 17, 2023, 11:19 AM

#

stuck bridge what psu

small 5v one powering pi and the 24v one

stuck bridge Sep 17, 2023, 11:19 AM

#

did u tape usb

small karma Sep 17, 2023, 11:19 AM

#

stuck bridge did u tape usb

wym lol

stuck bridge Sep 17, 2023, 11:20 AM

#

unplug the usb cable to printer and power cycle

#

see if its detected

small karma Sep 17, 2023, 11:20 AM

#

ok

#

power cicled, will try to ssh

small karma Sep 17, 2023, 11:26 AM

#

stuck bridge see if its detected

appearing on router, connection refused through

stuck bridge Sep 17, 2023, 11:29 AM

#

small karma appearing on router, connection refused through

tape 5v on usb

small karma Sep 17, 2023, 11:29 AM

#

stuck bridge tape 5v on usb

to power the pi? use an external psu works?

stuck bridge Sep 17, 2023, 11:30 AM

#

to printer

#

check voltage too on psu

small karma Sep 17, 2023, 11:30 AM

#

so i just recconect the usb and check voltage?

stuck bridge Sep 17, 2023, 11:39 AM

#

check psu source voltage

#

tape 5v on usb then connect

small karma Sep 17, 2023, 11:39 AM

#

stuck bridge tape 5v on usb then connect

checked, 5v on psu

#

got a broken pipe error once

#

now only connection refused

stuck bridge Sep 17, 2023, 11:41 AM

#

exactly?

#

5v

small karma Sep 17, 2023, 11:42 AM

#

stuck bridge 5v

like 5.06v

stuck bridge Sep 17, 2023, 11:46 AM

#

are you on the same wifi as the printer’s ethernet?

small karma Sep 17, 2023, 11:49 AM

#

stuck bridge are you on the same wifi as the printer’s ethernet?

yep, both connected via ethernet, i can ssh in it using my dads mac now for whatever reason, will try to get kiauh running here and then ssh in my pc

#initial Klipper setup on a v2.4