asking for klipper help and tips | 3D Printing | Page 1

dire yacht Jun 20, 2023, 1:18 AM

#

is there anyone that would like to help me get the most out of my ender 3 with klipper and like just help with tuning it and making sure im doing it right?

ocean oysterBOT Jun 20, 2023, 1:18 AM

#

dire yacht is there anyone that would like to help me get the most out of my ender 3 with k...

#

AI Help

I'm happy to help you get the most out of your Ender 3 with Klipper! Some basic information I'd need first is what kind of upgrades you have on your printer, what issues you're experiencing, what filament you're using, and what slicer and Klipper configurations you have set up already.

dire yacht Jun 20, 2023, 1:19 AM

#

ender 3

#

dragonfly hotend

#

new fan

#

capricorn tubbing

#

cr touch

valid radish Jun 20, 2023, 1:21 AM

#

how new we talking? i would start with the docs and ask if you got questions https://www.klipper3d.org/Config_checks.html

dire yacht Jun 20, 2023, 1:21 AM

#

i have it working and all that

#

it prints and at 180 with like 6000 accel

#

i just dont know how to make it better and have a much cleaner and more effective setup

valid radish Jun 20, 2023, 1:22 AM

#

done all the basic tuning again?

dire yacht Jun 20, 2023, 1:23 AM

#

kinda

#

yes but i need to redo them

#

but start up takes like 10 to 15 mins

valid radish Jun 20, 2023, 1:24 AM

#

after a PID tune? seems slow

#

like heatup alone?

dire yacht Jun 20, 2023, 1:25 AM

#

valid radish like heatup alone?

yeah

#

and it does the bed and hotend separately

#

[gcode_macro START_PRINT]
gcode:
{% set BED_TEMP = params.BED_TEMP|default(60)|float %}
{% set EXTRUDER_TEMP = params.EXTRUDER_TEMP|default(215)|float %}
{% set EXTRUDER_STANDBY_TEMP = params.EXTRUDER_TEMP|default(170)|float %}
G28
G90
G92 E0 ; Reset Extruder
M82
M140 S{BED_TEMP} ;Start heating bed
M104 S{EXTRUDER_STANDBY_TEMP} ;Start heating extruder
M190 S{BED_TEMP} ;Wait for bed to reach temp before proceeding
G28 ; Home all axes
#BED_MESH_CALIBRATION
BED_MESH_PROFILE LOAD=default
M109 S{EXTRUDER_TEMP} ;Wait for extruder to reach temp before proceeding
G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed
G1 X0.1 Y20 Z0.3 F5000.0 ; Move to start position
G1 X0.1 Y200.0 Z0.2 F1500.0 E15 ; Draw the first line
G1 X0.4 Y200.0 Z0.2 F5000.0 ; Move to side a little
G1 X0.4 Y20 Z0.2 F1500.0 E30 ; Draw the second line
G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed
G1 X5 Y20 Z0.2 F5000.0 ; Move over to prevent blob squish
G92 E0 ; Reset Extruder

valid radish Jun 20, 2023, 1:28 AM

#

that sets the bed to the final and the extruder to 170 at the same time, then waits for the bed

#

you wan to change the extruder to heat closer to final temps?

dire yacht Jun 20, 2023, 1:29 AM

#

whatever is best

valid radish Jun 20, 2023, 1:30 AM

#

take out the first G28 on the 4th line of the macro, dont need to home before heating, otherwise that seems pretty optimal

dire yacht Jun 20, 2023, 1:31 AM

#

Ok ok

#

#

Should I keep going?

valid radish Jun 20, 2023, 1:33 AM

#

that supposed to be a pressure advance test?

dire yacht Jun 20, 2023, 1:33 AM

#

Yes

valid radish Jun 20, 2023, 1:34 AM

#

try following this, but use one wall https://www.klipper3d.org/Pressure_Advance.html

#

you get buldging corners on the bottom that will get smaller and smaller untill the corner fails

dire yacht Jun 20, 2023, 1:35 AM

#

ok ill try it

#

how do i home my printer since i took that one out

valid radish Jun 20, 2023, 1:38 AM

#

you have another home in there

#

you were homing, heating, then homing again

dire yacht Jun 20, 2023, 1:39 AM

#

Make sure any "dynamic acceleration control" is disabled in the slicer.

#

where is this in prusa slicer

#

?

valid radish Jun 20, 2023, 1:40 AM

#

0 to all and control acceleration through klipper

dire yacht Jun 20, 2023, 1:40 AM

#

ohhh ok

#

44mins?

#

with this for speeds

#

valid radish Jun 20, 2023, 1:42 AM

#

you walls at 1 and no infill?

dire yacht Jun 20, 2023, 1:43 AM

#

if walls is parameters then now its 23 mins

#

and no infill

valid radish Jun 20, 2023, 1:44 AM

#

sounds better, but will probably start failing sooner

#

it wont pull off the bed if you have good adhsesion but watch it

dire yacht Jun 20, 2023, 1:45 AM

#

ok ill watch it\

ocean oysterBOT Jun 20, 2023, 2:48 AM

#

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

dire yacht Jun 20, 2023, 2:48 AM

#

Mb

dire yacht Jun 20, 2023, 3:01 AM

#

valid radish sounds better, but will probably start failing sooner

Here

#

#

I had to leave but I'm back

valid radish Jun 20, 2023, 3:03 AM

#

you run the right TUNING_TOWER COMMAND=SET_PRESSURE_ADVANCE PARAMETER=ADVANCE START=0 FACTOR=xxx? seems the same all around

dire yacht Jun 20, 2023, 3:03 AM

#

uh

#

ohhhhhhhhh

#

#

aslso its not doing it at the same time

valid radish Jun 20, 2023, 3:10 AM

#

you saved and restarted?

#

if so M104 S{EXTRUDER_STANDBY_TEMP} ;Start heating extruder can change to M104 S170 ;Start heating extruder to har code it

dire yacht Jun 20, 2023, 3:41 AM

#

I fixed it now

#

rn_image_picker_lib_temp_cae1c5f5-74d6-4673-b75e-442c19c78ff3.jpg

valid radish Jun 20, 2023, 3:46 AM

#

follow the docs, one corner will be worse if the seam was on it, but measur up and multiply by layerheight to find your pressure advance

dire yacht Jun 20, 2023, 3:47 AM

#

Ok ok

dire yacht Jun 20, 2023, 4:35 AM

#

10

#

mm

#

.2 is the presure advance

#

like i had it'

ocean oysterBOT Jun 20, 2023, 5:38 AM

#

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

dire yacht Jun 20, 2023, 1:49 PM

#

valid radish follow the docs, one corner will be worse if the seam was on it, but measur up a...

So that setting was already checked but ig it was good to do it again

ocean oysterBOT Jun 20, 2023, 2:53 PM

#

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

dire yacht Jun 20, 2023, 5:01 PM

#

yeah i think im good on that

#asking for klipper help and tips