CR 6 SE Exetruder skipping | 3D Printing | Page 1

final oasis May 15, 2023, 10:19 PM

#

Hello, I'm starting to have some problems on my cr 6 se with extruder skipping, tried to fix it by changing, bowden tube, gears, retraction speed and distance and nozzle
Anyone have an idea how to fix this?

olive boltBOT May 15, 2023, 10:19 PM

#

final oasis Hello, I'm starting to have some problems on my cr 6 se with extruder skipping, ...

#

AI Help

Extruder skipping can be caused by several factors. Here are a few troubleshooting steps you can follow:

Check the filament: Ensure that your filament is not tangled or knotted, and ensure that it is not too old or brittle.
Clean the nozzle: Sometimes a clogged or dirty nozzle can cause extruder skipping. Try cleaning the nozzle by using a nozzle cleaner, or try using a new nozzle.
Check the extruder motor: Check if your extruder motor is working properly. You can test this by turning on your printer and manually pushing the filament through the extruder. If the extruder motor is not working properly, you may need to replace it.
Check the extruder tension: Ensure that the extruder tension is not too tight or too loose. Adjust the tension to see if it helps.
Check the hotend temperature: It's possible that the hotend temperature could be too low, causing the filament to not properly melt. Try adjusting the temperature to see if it helps.

I hope these tips help yo...

idle hull May 15, 2023, 10:23 PM

#

final oasis Hello, I'm starting to have some problems on my cr 6 se with extruder skipping, ...

have you upgraded your extruder?

final oasis May 15, 2023, 10:24 PM

#

idle hull have you upgraded your extruder?

Nope, i have just replaced the hotend

idle hull May 15, 2023, 10:24 PM

#

check for cracks on your extruder

final oasis May 15, 2023, 10:24 PM

#

there are none

#

i use metal extruder

idle hull May 15, 2023, 10:24 PM

#

can you send a pic of the extruder

final oasis May 15, 2023, 10:24 PM

#

ofc

idle hull May 15, 2023, 10:24 PM

#

the one which you put the filament in

final oasis May 15, 2023, 10:25 PM

#

idle hull May 15, 2023, 10:25 PM

#

check your tension

#

and if you have a clog

final oasis May 15, 2023, 10:26 PM

#

what is tension

idle hull May 15, 2023, 10:26 PM

#

that spring

final oasis May 15, 2023, 10:27 PM

#

and what should i look for

idle hull May 15, 2023, 10:30 PM

#

good question

#

uh

#

take the filament out

#

and check how deep the markings are

final oasis May 15, 2023, 10:45 PM

#

like one or two? im not the biggest tech expert

idle hull May 15, 2023, 10:45 PM

#

1

final oasis May 15, 2023, 10:46 PM

#

so i should screw it off?

idle hull May 15, 2023, 11:00 PM

#

take the filament out
and check how deep the markings are

final oasis May 15, 2023, 11:06 PM

#

just the spring?

idle hull May 15, 2023, 11:07 PM

#

follow my instructions

#

take the filament out

#

check how deep the grooves are

final oasis May 15, 2023, 11:09 PM

#

yeah but check where?

idle hull May 15, 2023, 11:15 PM

#

on the filament

final oasis May 15, 2023, 11:17 PM

#

Some Marks it have

buoyant valve May 15, 2023, 11:35 PM

#

?thegap

olive boltBOT May 15, 2023, 11:35 PM

#

https://cdn.discordapp.com/attachments/339978089411117076/863813291566170123/Hotend101.png

final oasis May 15, 2023, 11:40 PM

#

idle hull on the filament

So what You Think?

olive boltBOT May 16, 2023, 12:42 AM

#

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

idle hull May 16, 2023, 3:02 AM

#

those look fine

#

hm

#

check for the gap

#CR 6 SE Exetruder skipping