prints failing | 3D Printing | Page 1

indigo dirge Apr 11, 2023, 7:33 PM

#

prints keep failing after i start them (after it homes and heats up)

wicked helmBOT Apr 11, 2023, 7:33 PM

#

indigo dirge prints keep failing after i start them (after it homes and heats up)

#

AI Help

There are several possible reasons why your prints are failing after starting. Here are some things to check:

Bed adhesion: Make sure that your print bed is clean and that the material is sticking properly to the bed. If not, try using printer glue, hairspray or other adhesion agents to improve bed adhesion.
Leveling the bed: Check that the bed level is correct. If the bed is not leveled correctly, the nozzle may not be the correct distance away from the bed to extrude material correctly.
Clog in the nozzle: A clogged nozzle can cause a lack of material leaving the nozzle, leading to imperfect printing. Heat the nozzle up to the recommended temperature for the material you are printing and try to clear it.
Filament issues: Check if the filament is tangled or if there are dust particles on it. Clean the filament and try again.
Software settings: Verify that your slicer settings are correct. Ensure the filament diameter is accurate, slicing settings are optimized f...

indigo dirge Apr 11, 2023, 7:34 PM

#

ender 3 pro, bl touch running klipper with mainsail front end

cedar briar Apr 11, 2023, 7:36 PM

#

im not familiar with klipper, but Ender 3 Pro bed has a size of 235x235 but your error is saying the printer is trying to get to y dimension of 335 which isnt possible. Have you set the bed size correctly in firmware?

indigo dirge Apr 11, 2023, 7:37 PM

#

yes

#

it was working last night

#

but when i started it today it didnt want to work

#

and i changed nothing

exotic jetty Apr 11, 2023, 7:52 PM

#

send you klipper log, and do you have a G91 in your start gcode? going to an exact number like 335.000 is usually not normal

wicked helmBOT Apr 11, 2023, 8:52 PM

#

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

indigo dirge Apr 12, 2023, 6:35 PM

#

exotic jetty send you klipper log, and do you have a G91 in your start gcode? going to an exa...

this is my start g code ; Ender 3 Custom Start G-code G92 E0 ; Reset Extruder G28 ; Home all axesa BED_MESH_PROFILE LOAD=default M104 S{material_standby_temperature} ; Start heating up the nozzle most of the way M190 S{material_bed_temperature_layer_0} ; Start heating the bed, wait until target temperature reached M109 S{material_print_temperature_layer_0} ; Finish heating the nozzle G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed G1 X0.1 Y20 Z0.3 F5000.0 ; Move to start position G1 X0.1 Y200.0 Z0.3 F1500.0 E15 ; Draw the first line G1 X0.4 Y200.0 Z0.3 F5000.0 ; Move to side a little G1 X0.4 Y20 Z0.3 F1500.0 E30 ; Draw the second line G92 E0 ; Reset Extruder G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed G1 X5 Y20 Z0.3 F5000.0 ; Move over to prevent blob squish

#

all thats changed from the stock one is the bedmesh line

#

but i tried printing a print ive done before and it also failed

#

ill upload the log in a min or 2

exotic jetty Apr 12, 2023, 6:36 PM

#

post your gcode as well, just in case its in there somewhere else

wicked helmBOT Apr 12, 2023, 7:42 PM

#

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

indigo dirge Apr 13, 2023, 10:54 PM

#

📎 CE3PRO_fat_seal.gcode

#

ok so it was a lil more then a min or 2

#

but heres my g code

#

just restarted and it seems to be working again

#

sometimes it does sometimes it doesnt

#prints failing