[SOLVED] Lane PREP error | ArmoredTurtle 3D | Page 1

unborn acorn Jun 7, 2025, 12:55 PM

#

Cannot load lane3 load sensor is triggered.
Make sure filament is not stuck in load sensor or check to make sure load sensor is not stuck triggered.
Once cleared try loading again

If I load the filament, I get the READY
If I run prep, I just get the lane3 tool cmd: T2 CHECK FILAMENT Prep: False - Load: True error
8:50 AM
R _____ ____
E / \ | o |
A | |/ /
D |__/
Y ||| |||
Turtle_1
8:50 AM
lane4 tool cmd: T3 EMPTY READY FOR SPOOL
8:50 AM
lane3 tool cmd: T2 LOCKED AND LOADED

amber mountainBOT Jun 7, 2025, 12:56 PM

#

<@&1304550334839918672>

rose copper Jun 7, 2025, 1:04 PM

#

Did you check your load sensor to make sure nothing is in the path?

#

Or maybe it could be stuck triggered

#

Also what does your load sensor show in your web gui?

unborn acorn Jun 7, 2025, 1:16 PM

#

I will check, there's nothing stuck,

#

#

lane3 tool cmd: T2 CHECK FILAMENT Prep: False - Load: True
from the console

tame lantern Jun 7, 2025, 1:22 PM

#

can you run this?

cd ~/AFC-Klipper-Add-On/troubleshooting
./afc-debug.sh

unborn acorn Jun 7, 2025, 1:23 PM

#

thanks so much! doing it now!

rose copper Jun 7, 2025, 1:25 PM

#

unborn acorn

yeah, this won't show it. Need to check the filament/runout sensor location

unborn acorn Jun 7, 2025, 1:25 PM

#

https://termbin.com/g0zj

#

I do not have a filament run out sensor

#

or are you talking about the sensor on the tool head?

rose copper Jun 7, 2025, 1:28 PM

#

you load sensors should show up in your miscellaneous section in mainsail

unborn acorn Jun 7, 2025, 1:28 PM

#

oh ok, thanks

tame lantern Jun 7, 2025, 1:29 PM

#

            "load": true,
            "prep": false,

#

Would this not mean the prep (the trigger arm thing) isn't being triggered properly

#

on lane 3

unborn acorn Jun 7, 2025, 1:30 PM

#

unborn acorn Jun 7, 2025, 1:31 PM

#

tame lantern on lane 3

It is touching the arm and fully depressed,

rose copper Jun 7, 2025, 1:32 PM

#

No the load sensor in your extruder is being triggered

unborn acorn Jun 7, 2025, 1:34 PM

#

ok so it is the other one then, I will check the wiring there.

#

rose copper Jun 7, 2025, 1:35 PM

#

also check to make sure filament is not stuck in there, like try to put some filament in the rear of the extruder and see if it deactivates it when you remove the filament

unborn acorn Jun 7, 2025, 1:35 PM

#

This?

rose copper Jun 7, 2025, 1:35 PM

#

yes

unborn acorn Jun 7, 2025, 1:36 PM

#

Thanks,

unborn acorn Jun 7, 2025, 1:56 PM

#

Thanks, it was a stuck piece of filament. 🙂 @rose copper|BBT-4|BT-4|HTLF-4 I appreciate all of your help!

#

we can close this ticket

#[SOLVED] Lane PREP error