I put in my sensor pin and now klipper wont launch
#disaster1234
trim wave
waxen dove
I put in my sensor pin and now klipper wont launch
Did you do a fresh install? Or is this on a previous version?
waxen dove
So did it properly put it in AFC_Hardware? Oh, not sure what that is.
spiral stirrup
its fubared anyway keep getting 500 server error anyway
500 or 502 type of errors means that moonraker or something is not running correctly
trim wave
Re-installing moonraker now
trim wave
failed again 500 internal server issue
trim wave
12:13 PM
Endstop y still triggered after retract
trim wave
Any suggestions ...after QGL \Homing then hit print. Tool head is moving to the front right x end stop and stopping. triggering the error Endstop y still triggered after retract
prisma lark
This sounds like a base printer problem and not a box turtle problem?
trim wave
Yea after commenting out everything i found the issue. A heater issue even though log files pointed to neopixels
green drum
@trim wave hows it going been rooting for ya
trim wave
<@399386930149588992> hows it going been rooting for ya
Haven't touched it for awhile. Been printing a fun print for the moment. Will get back it in a few min.
The 3dsets reaper
But glad you ask.
green drum
Had to google that and I need to make u my new best friend lmao been wanting to try something like this
trim wave
I built the sakura also from 3dsets.com Both Full RC cars
but back to testing BT '
warming up voron now for testing
LEG4 tool cmd: T3 LOCKED AND LOADED
10:19 PM
Error trying to map lane ['leg4'] to T3, please make sure there are no macros already setup for T3
10:19 PM
LEG3 tool cmd: T2 LOCKED AND LOADED
10:19 PM
Error trying to map lane ['leg3'] to T2, please make sure there are no macros already setup for T2
10:19 PM
LEG2 tool cmd: T1 LOCKED AND LOADED
10:19 PM
Error trying to map lane ['leg2'] to T1, please make sure there are no macros already setup for T1
10:19 PM
LEG1 tool cmd: T0 LOCKED AND LOADED```Turtle_1 Status
LANE | Prep | Load |
LEG1 | <--> | <--> |
LEG2 | <--> | <--> |
LEG3 | <--> | <--> |
LEG4 | <--> | <--> |
HUB: x Tool: x```v0.0.0-1040 > v0.0.0-1042 afc update showing too
trim wave
Just will not hit the tool head... keeps doin ghe slow moves way to early ..so not sure what is causing the issue now
Think Imabout to just give up on this
Its not meant to be for me
green drum
No no no
green drum
Just will not hit the tool head... keeps doin ghe slow moves way to early ..so n...
What’s up the length of Bowden
trim wave
increased little by little from 1140 to 1600
and when trying to re-wind back to the roll shutters so bad I have to help re-wind the roll otherwise it will just throw all the filament up i nthe air all over the place
Im kinda bothered that I can build fully printed RC with no problem but can't build MMU
almost like the re-wind is not working properly
green drum
almost like the re-wind is not working properly
My buddy had same issue and the re spoolers were spinning the wrong way could it be that?
trim wave
My buddy had same issue and the re spoolers were spinning the wrong way could it...
Ill make a video tonight after work
thin pelican
```10:19 PM
LEG4 tool cmd: T3 LOCKED AND LOADED
10:19 PM
Error trying to map la...
This is normal
spiral stirrup
Well also make sure there are no T commands in any of your config files as well, that is why that error is showing up
thin pelican
Well also make sure there are no T commands in any of your config files as well,...
yeah i just expected the errors to pop since its been a bit since Mike was tinkering with this last. -> more trying to tell him its not broken you can continue
trim wave
Just got up ..going to tinker more
trim wave
I watched a video on the box turtle operation. Not sure if my rewind is correct. How do I go about testing the direction. It was pretty smooth compared to mine
like to try and get this going
spiral stirrup
you can do TEST in the command line and it should spin the motors like its rewinding filament back on the spool
trim wave
ok ill give it a go
test diednt do anything
Tried TEST T0
I Dont know the commaands
spiral stirrup
Sorry TEST LANE= and put your lane you wanna test after the equal
trim wave
Internal error on command:"TEST"
Once the underlying issue is corrected, use the
"FIRMWARE_RESTART" command to reset the firmware, reload the
config, and restart the host software.
Printer is shutdown
Did nt like that at all
v0.0.0-1040 > v0.0.0-1044 says I have a update ..but not updating
doesnt matter which lane klipper dies right away
spiral stirrup
You matching the lane name exactly how it is in your config?
trim wave
using default
10:30 PM
R _____ ____
E / \ | o |
A | |/ /
D |__/
Y ||| |||
Turtle_1
10:30 PM
LEG4 tool cmd: T3 LOCKED AND LOADED
10:30 PM
LEG3 tool cmd: T2 LOCKED AND LOADED
10:30 PM
LEG2 tool cmd: T1 LOCKED AND LOADED
10:30 PM
LEG1 tool cmd: T0 LOCKED AND LOADED
test kills klipper
spiral stirrup
are you using uppercase or lowercase leg, cause case matters. If you already used uppercase can you try with lowercase leg1
trim wave
both kill klipper
spiral stirrup
Can you put your log here please
trim wave
status
10:35 PM
Turtle_1 Status
LANE | Prep | Load |
LEG1 | <--> | <--> |
LEG2 | <--> | <--> |
LEG3 | <--> | <--> |
LEG4 | <--> | <--> |
HUB: x Tool: x
spiral stirrup
TEST LANE=leg1 is the right way according to your config
trim wave
filament is bouncing
spiral stirrup
It should move the motors at different speeds, probably should do it to a empty lane
trim wave
Ok rebooting pc. Froze up solid
spun right direction
10:50 PM
Leg1 not found in any unit.
10:50 PM
Starting AFC distance Calibrations
10:50 PM
CALIBRATE_AFC LANE=Leg1
winged torrent
what is the stepprname in cfg