Disaster1234 | ArmoredTurtle 3D | Page 3

dense sequoia Nov 28, 2024, 3:22 PM

#

yes jsut stopped 30mm above the sensor

desert heron Nov 28, 2024, 3:23 PM

#

dose it do the short moves and enter or dose the short moves stopp 30mm away?

#

it should move fast almost all the way down to the toolhead

dense sequoia Nov 28, 2024, 3:23 PM

#

short moves then stops

#

its doing short moves way before that

#

like 5 or 6

desert heron Nov 28, 2024, 3:23 PM

#

you need to up your hub distance a long bit

dense sequoia Nov 28, 2024, 3:24 PM

#

im at 1250mm right now

desert heron Nov 28, 2024, 3:25 PM

#

add the distance from where it starts doing the short moves to the toolhead.

#

and add that to the total

#

just ish. dont need to run again +-20mm should be fine

dense sequoia Nov 28, 2024, 3:26 PM

#

jsut add tha tto the length

desert heron Nov 28, 2024, 3:26 PM

#

yup

#

probebly en up with more than 1300mm if i guess

dense sequoia Nov 28, 2024, 3:26 PM

#

filament tangled again

#

i rewinded

desert heron Nov 28, 2024, 3:26 PM

#

just guess. its not that precise for now

#

your rewinder gears migt need a reprint. they seem to move poorly in the vidio

#

they should be quite fast and presise

#

years seem shaky

#

that can be fixed later tho

#

should still work as is

dense sequoia Nov 28, 2024, 3:28 PM

#

they are smooth

desert heron Nov 28, 2024, 3:29 PM

#

what length did you end up with?

dense sequoia Nov 28, 2024, 3:29 PM

#

1280 right now \

#

running T0

desert heron Nov 28, 2024, 3:29 PM

#

could start there. you should get 1 maybe 2 short moves. if more you need to add more.

#

perferably you shouldent get any att all

#

and your TN is fully exteded right?

dense sequoia Nov 28, 2024, 3:31 PM

#

Were the slow moves starts

rn_image_picker_lib_temp_a6946155-c037-4b4d-9a92-6bfe9de2f5ac.jpg

desert heron Nov 28, 2024, 3:31 PM

#

dense sequoia Were the slow moves starts

you need to add like 150mm more at least

#

maybe more

dense sequoia Nov 28, 2024, 3:33 PM

#

the filament is 30mm from top of the SB

#

right now

desert heron Nov 28, 2024, 3:34 PM

#

yes but you want to add the distance from where the short moves start. not end.

dense sequoia Nov 28, 2024, 3:34 PM

#

ok

desert heron Nov 28, 2024, 3:34 PM

#

the short moves are a safty backup. you perferably dont want them at all

dense sequoia Nov 28, 2024, 3:35 PM

#

👍

#

running it again

desert heron Nov 28, 2024, 3:35 PM

#

nice

dense sequoia Nov 28, 2024, 3:35 PM

#

filament re-winding \

#

let me fix the filament ...tangled again \

desert heron Nov 28, 2024, 3:36 PM

#

ahh and btw if you do the bt lane move the respoolers dont run

#

and if you do to long moves at once klipper crashes

dense sequoia Nov 28, 2024, 3:37 PM

#

only using bt unload

#

T0 again

desert heron Nov 28, 2024, 3:39 PM

#

did it enter?

dense sequoia Nov 28, 2024, 3:39 PM

#

add 150mm

desert heron Nov 28, 2024, 3:40 PM

#

need more

#

you have somthing thats jamming it

#

where is it stopping?

#

might be the sensor not having a smooth pass thrue

dense sequoia Nov 28, 2024, 3:41 PM

#

Right at the tool head g2e

desert heron Nov 28, 2024, 3:41 PM

#

dont move the filament

dense sequoia Nov 28, 2024, 3:41 PM

#

Ok

desert heron Nov 28, 2024, 3:42 PM

#

run the AFC_STATUS

#

and send a pic of the result

#

should look like this

dense sequoia Nov 28, 2024, 3:42 PM

#

42 AM
Turtle_1 Status
LANE | Prep | Load | Hub | Tool |
LEG1 | <--> | <--> | x | xx |
LEG2 | <--> | <--> | x | xx |
LEG3 | <--> | <--> | x | xx |
LEG4 | <--> | <--> | x | xx |

desert heron Nov 28, 2024, 3:42 PM

#

is the filament pass the sensor?

dense sequoia Nov 28, 2024, 3:42 PM

#

hub switch isn't working

#

oh yea

desert heron Nov 28, 2024, 3:43 PM

#

yea that explains som stuff

dense sequoia Nov 28, 2024, 3:43 PM

#

desert heron Nov 28, 2024, 3:43 PM

#

unloade the filament and run the comand again

#

i think you hub signal is inverted

#

when you run the comand again there should not be anny filamen left in the hub

dense sequoia Nov 28, 2024, 3:48 PM

#

Guess another junk switch

#

feed filament from back and still not detecing it

desert heron Nov 28, 2024, 3:49 PM

#

run the comand withou anything in there

dense sequoia Nov 28, 2024, 3:49 PM

#

3rd switch ...was working yesterday

#

Turtle_1 Status
LANE | Prep | Load | Hub | Tool |
LEG1 | xx | xx | x | xx |
LEG2 | <--> | <--> | x | xx |
LEG3 | <--> | <--> | x | xx |
LEG4 | <--> | <--> | x | xx |

#

empty

desert heron Nov 28, 2024, 3:49 PM

#

you have the new hub right?

#

and you solderd them like the guide?

dense sequoia Nov 28, 2024, 3:50 PM

#

yess with single screw

#

yes

#

NC soldered

desert heron Nov 28, 2024, 3:50 PM

#

thats odd. they should be realy reliable. somthings odd

#

i whould guess you wiring is bad a a bad crimp

#

the switch itself is realy nice if you got the one from the bom

stable meadow Nov 28, 2024, 3:52 PM

#

dense sequoia feed filament from back and still not detecing it

can you hear the switch go "click click" when you pass filament through it?

dense sequoia Nov 28, 2024, 3:53 PM

#

yes

#

guess ill take apart again for the 100th time

desert heron Nov 28, 2024, 3:54 PM

#

did you putt the crips upside down in the conector?

#

i did that once.

#

they should all lign up on one sid e

dense sequoia Nov 28, 2024, 3:54 PM

#

no

#

Im think I might be getting to the point of just selling it

desert heron Nov 28, 2024, 3:57 PM

#

your so close

#

i thing you should recrimp the hub sensor. it might be a bad conection. thats all

stable meadow Nov 28, 2024, 3:59 PM

#

dense sequoia yes

just asking cuz i lost my click click noise on 1 of my switches i thought died and it was just the bearing not hitting the switch

dense sequoia Nov 28, 2024, 4:58 PM

#

almoat back together

stable meadow Nov 28, 2024, 5:00 PM

#

https://tenor.com/view/minions-despicableme-cheer-happy-yay-gif-1862643858806798699

Tenor

dense sequoia Nov 28, 2024, 5:03 PM

#

T0

#

then afc _status

desert heron Nov 28, 2024, 5:04 PM

#

https://tenor.com/view/httyd3-hiccup-approve-great-thumbs-up-gif-4827785971694395024

Tenor

olive field Nov 28, 2024, 5:07 PM

#

https://tenor.com/view/bubu-dudu-bubu-dudu-love-dudu-bubu-love-dudu-love-bubu-love-dudu-bubu-gif-388489720610011907

Tenor

desert heron Nov 28, 2024, 5:12 PM

#

dense sequoia then afc _status

how did it go?

dense sequoia Nov 28, 2024, 5:13 PM

#

terriable

desert heron Nov 28, 2024, 5:13 PM

#

o no

dense sequoia Nov 28, 2024, 5:13 PM

#

filament now getting stuck in TN2

desert heron Nov 28, 2024, 5:14 PM

#

dense sequoia filament now getting stuck in TN2

chech the exit ptfe tube

#

you might have uneven cut

#

if not, you can champher it with a knife or somthing

stable meadow Nov 28, 2024, 5:14 PM

#

dense sequoia filament now getting stuck in TN2

where at in the TN2 i had this problem

dense sequoia Nov 28, 2024, 5:16 PM

#

see one issue turns into another ...rebooting

#

Ill try again after homing

#

Im rfeady for some turkey and burbon

stable meadow Nov 28, 2024, 5:18 PM

#

dense sequoia Im rfeady for some turkey and burbon

my aunt would say "its noon somewhere"

dense sequoia Nov 28, 2024, 5:19 PM

#

klipper just creashed

#

why cant anything just go smooth

desert heron Nov 28, 2024, 5:19 PM

#

dense sequoia klipper just creashed

can you send your log?

stable meadow Nov 28, 2024, 5:19 PM

#

did the turtle prep or not before crash?

stable meadow Nov 28, 2024, 5:20 PM

#

dense sequoia why cant anything just go smooth

theres some ancient japanese wisdom about the easy path and the hard path but that seems extra KEKW you got this bro literally so close

dense sequoia Nov 28, 2024, 5:20 PM

#

mine is the hard path thats for sure

#

T0 \

desert heron Nov 28, 2024, 5:21 PM

#

can you pliz share you kllippy log? it should tell us why it keeps crashing

stable meadow Nov 28, 2024, 5:21 PM

#

🤞🏻

dense sequoia Nov 28, 2024, 5:21 PM

#

Then i still have to fiigure out the cutter issue too

#

snappy

stable meadow Nov 28, 2024, 5:21 PM

#

1 small step at a time

dense sequoia Nov 28, 2024, 5:22 PM

#

well now its even worse o nthe filament push

#

and no Hub trigger

desert heron Nov 28, 2024, 5:23 PM

#

can you pliz send the log

dense sequoia Nov 28, 2024, 5:23 PM

#

Sure butI think Im going hitthe burbon early

#

i think Im going to throw this out the window

desert heron Nov 28, 2024, 5:24 PM

#

thats fair but the log might have som awnsers

dense sequoia Nov 28, 2024, 5:24 PM

#

kidding

desert heron Nov 28, 2024, 5:24 PM

#

and it dose not spitt out a dead turtle in the terminal either?

#

on boot

dense sequoia Nov 28, 2024, 5:25 PM

#

📎 klippy_8.log

#

12:23 PM
Turtle_1 Status
LANE | Prep | Load | Hub | Tool |
LEG1 | <--> | <--> | x | xx |
LEG2 | <--> | <--> | x | xx |
LEG3 | <--> | <--> | x | xx |
LEG4 | <--> | <--> | x | xx |

#

I'm not taking it apart again

desert heron Nov 28, 2024, 5:26 PM

#

i have a simple 5 min test for your hub

#

take a multi meter

dense sequoia Nov 28, 2024, 5:26 PM

#

Yes I did that

desert heron Nov 28, 2024, 5:27 PM

#

what did it read and where did you probe?

dense sequoia Nov 28, 2024, 5:27 PM

#

and the multimeter beeps when filament was moving in and out

#

putt hub back in quits working

#

right at the switch

#

and also o nthe crimps

#

while hub was out

desert heron Nov 28, 2024, 5:28 PM

#

you need to probe at the crimps. but it read right when it was not in the board?

dense sequoia Nov 28, 2024, 5:28 PM

#

was plugged in

#

i used the top of the crimp

desert heron Nov 28, 2024, 5:29 PM

#

we might be onto somthing. could you share a picture of your afc board in the bt with everything mountes as you whould use it? i think you might have done the same as i did

#

and what version of AFC software did you update to?

dense sequoia Nov 28, 2024, 5:30 PM

#

afc-software
v0.0.0-767-g51e173b4-inferred

desert heron Nov 28, 2024, 5:31 PM

#

huh i see you got the prep crash at least once. thats odd

dense sequoia Nov 28, 2024, 5:31 PM

#

desert heron Nov 28, 2024, 5:31 PM

#

nice picture. give me 2 min

dense sequoia Nov 28, 2024, 5:32 PM

#

nothing odd about this box turtle

stable meadow Nov 28, 2024, 5:32 PM

#

desert heron huh i see you got the prep crash at least once. thats odd

was wondering if he was crashing at prep ive had that sometimes as well because i sourced different n20 than the ali express BOM ones.

#

they stall

dense sequoia Nov 28, 2024, 5:33 PM

#

all mine game from a kit

stable meadow Nov 28, 2024, 5:33 PM

#

dense sequoia nothing odd about this box turtle

your black/blue wires on a switch how are they going into the switch

desert heron Nov 28, 2024, 5:33 PM

#

don think thats the issue right now

dense sequoia Nov 28, 2024, 5:33 PM

#

blue all NC

desert heron Nov 28, 2024, 5:34 PM

#

your how wiers seem thicker than the rest. might be an idea to rewire it sompleatly. might have a damagde cable

dense sequoia Nov 28, 2024, 5:34 PM

#

that was old pic sorry i changed al lthe NC to blue and grounds are black \

desert heron Nov 28, 2024, 5:34 PM

#

the wiring itself is correct

dense sequoia Nov 28, 2024, 5:34 PM

#

24AWG

desert heron Nov 28, 2024, 5:34 PM

#

thats not to thick.

#

i have to go but if i where you i whould rewire the hub switch with new wire and crimps

dense sequoia Nov 28, 2024, 5:35 PM

#

Just did that

#

I think Im out of switches

desert heron Nov 28, 2024, 5:36 PM

#

Check your pull-up in the cfg

dense sequoia Nov 28, 2024, 5:37 PM

#

well everyone go enjoy time with family ..that's more important

#

switch_pin: ^AFC:HUB

#

I might mes with it later ..getting hungry

olive field Nov 28, 2024, 5:44 PM

#

Launch is important too ahah don't starve yourself mike heh

dense sequoia Nov 28, 2024, 5:44 PM

#

tol head just crashed in front left

#

nahhh

#

Thanks for tryuing so far on this T- day Holiday

#

stopped pushing about pushing 350mm this time ...just keeps going backwards

#

https://tenor.com/view/thanks-thanksgiving-happy-gif-15646024086925303336

Tenor

#

Have a wonderful day !!!

dense sequoia Nov 28, 2024, 7:53 PM

#

printing some fun prints for now

olive field Nov 28, 2024, 9:18 PM

#

noice it’s always great to print fun things sometime, last thing was a tic tac gun

dense sequoia Nov 28, 2024, 9:57 PM

#

yea well since I cant print on the voron since the BT is down

#

I think I'm just goping to remove it.

desert heron Nov 28, 2024, 10:19 PM

#

Just comment out the include part in the printer.cfg

#

That’s all you need to do.

dense sequoia Nov 28, 2024, 10:35 PM

#

any tricks to get a 0.4 broken needle out of nozzle hotend or is the nozzle shot ?

#

x1c

desert heron Nov 28, 2024, 10:42 PM

#

dense sequoia any tricks to get a 0.4 broken needle out of nozzle hotend or is the nozzle sho...

take of the nozzle and push it all the way out the other end

dense sequoia Nov 28, 2024, 10:44 PM

#

i tried

#

no go

#

Guess it's junk

#

Like a sleather

#

Ill never get it out

#

Well 2 printers down now

white igloo Nov 28, 2024, 10:51 PM

#

do a cold pull

dense sequoia Nov 28, 2024, 10:52 PM

#

Tried

dense sequoia Nov 28, 2024, 11:07 PM

#

Ill have to order another nozzle

#

Revo looks intesting

desert heron Nov 28, 2024, 11:16 PM

#

yes but expenciv as heck

#

i have paid 80$ for a nozzle

dense sequoia Nov 28, 2024, 11:16 PM

#

Yea

desert heron Nov 28, 2024, 11:16 PM

#

thats norwigan taxes and stuff tho

dense sequoia Nov 28, 2024, 11:17 PM

#

But still least the nozzle is removable this one is not

desert heron Nov 28, 2024, 11:17 PM

#

fair but you will lose a bit of flow.

dense sequoia Nov 28, 2024, 11:18 PM

#

And I can see the broken part

#

Ill get the revo hf

desert heron Nov 28, 2024, 11:18 PM

#

stll tho

dense sequoia Nov 28, 2024, 11:18 PM

#

X1c nozzle not s hf

desert heron Nov 28, 2024, 11:18 PM

#

take som epliers or somthing. hold it by the broken part. use a lighter on the nozzle untill it fals out

dense sequoia Nov 28, 2024, 11:19 PM

#

I tried a heatgun

desert heron Nov 28, 2024, 11:19 PM

#

dense sequoia X1c nozzle not s hf

https://e3d-online.com/products/hf-obx-bambu?srsltid=AfmBOooD7PaaIp3J4E_A9KMfvmgKubvaHFeXYY6G_qONVOxr7AqoynJs

E3D

E3D High Flow ObXidian™ HotEnd for Bambu Lab X1/P1 Series

Boost your 3D printing with E3D & Bambu Lab ObXidian High Flow HotEnds. Elevate performance with a 60% increase in flow rate, enhanced durability via E3DLC™ coating, and easy compatibility with X1, X1 Carbon, P1S, and P1P. A seamless upgrade for unparalleled printing efficiency.

dense sequoia Nov 28, 2024, 11:19 PM

#

Yes that's the hotend that has the broken needle stuck

#

.04

desert heron Nov 28, 2024, 11:20 PM

#

ahh got it. you cant just take another needle and push it all the way thrue?

dense sequoia Nov 28, 2024, 11:20 PM

#

Tried that toov

#

With a heatgun...no go

desert heron Nov 28, 2024, 11:21 PM

#

heatguns dont get that hot tho

#

try a lighter

#

that has never failed me

dense sequoia Nov 28, 2024, 11:22 PM

#

My heatgun gets really hot...wagner

#

Ill try heating it up hotter

#

On highest setting

#

Just my luck I guess

hidden plank Nov 28, 2024, 11:44 PM

#

yeah that's the downside to the bambu hotends, need a new one, gotta chuck it

dense sequoia Nov 28, 2024, 11:45 PM

#

Yea since i unable to get the broken needle out expensive loss

#

Obsidian nozzle

desert heron Nov 29, 2024, 12:10 AM

#

But don’t get a revo. They cost the same and a are fair bit weaker. I have snapped 2 80$ nozzles. On was even at the end of a print. The nozzle and the model had a fight and the nozzle won.

#

dense sequoia Nov 29, 2024, 12:17 AM

#

Oh

#

Ill go get some more nylon tomorrow and see if I can get it removed 1st

#

I'd say probably zero chance though

#

Printing on ender 3v3 for now

dense sequoia Nov 29, 2024, 3:41 PM

#

Ok I just verified with a multimeter that the switch is working. Checked at the crimped ends and the switch itself I get tone each time

stable meadow Nov 29, 2024, 3:57 PM

#

i really suck at crimping (myself) and sometimes i dont get the crimp on the metal of the wire

you think thats a chance?

dense sequoia Nov 29, 2024, 3:58 PM

#

i get tone from the meter

#

in and out

#

very strange

#

i just checked with a volt meter tone while the hub installed with filament ..but checking status nothing

lucid acorn Nov 29, 2024, 4:07 PM

#

better way to check the hub and toolhead is with duplicate pin override

stable meadow Nov 29, 2024, 4:20 PM

#

dense sequoia i get tone from the meter

im presuming by this response that your meter is checking at the plug itself not the switch

hidden plank Nov 29, 2024, 4:21 PM

#

yes

#

(Based on past testing with mike)

dense sequoia Nov 29, 2024, 4:22 PM

#

I checked both ends

#

just 10min ago

#

crimps/switch

hidden plank Nov 29, 2024, 4:24 PM

#

so for example try adding this to your AFC_Hardware.cfg at the end

[duplicate_pin_override]
pins: AFC:HUB

[filament_switch_sensor AFC_Hub_Sensor]
switch_pin: ^AFC:HUB
pause_on_runout: False

dense sequoia Nov 29, 2024, 4:27 PM

#

11:26 AM
Turtle_1 Status
LANE | Prep | Load | Hub | Tool |
LEG1 | <--> | <--> | x | xx |
LEG2 | xx | xx | x | xx |
LEG3 | xx | xx | x | xx |
LEG4 | xx | xx | x | xx | filamet to the toolhead

#

Have a great Day ! all

hidden plank Nov 29, 2024, 4:39 PM

#

what are the contents of your AFC/.var. files and what does <yourprinterip>/printer/objects/query?AFC return

dense sequoia Nov 29, 2024, 4:44 PM

#

        "leg1": {
            "spool_id": "",
            "material": "",
            "color": "#000000",
            "weight": 0,
            "command": null,
            "index": 1,
            "tool_loaded": false,
            "hub_loaded": true
        },
        "leg2": {
            "spool_id": "",
            "material": "",
            "color": "#000000",
            "weight": 0,
            "command": null,
            "index": 2,
            "tool_loaded": false,
            "hub_loaded": false
        },
        "leg3": {
            "spool_id": "",
            "material": "",
            "color": "#000000",
            "weight": 0,
            "command": null,
            "index": 3,
            "tool_loaded": false,
            "hub_loaded": false
        },
        "leg4": {
            "spool_id": "",
            "material": "",
            "color": "#000000",
            "weight": 0,
            "command": null,
            "index": 4,
            "tool_loaded": false,
            "hub_loaded": false
        }
    }
}```

hidden plank Nov 29, 2024, 4:45 PM

#

so your toolhead sensor is not showing as triggered here

#

?

#

or maybe it's just not recongized as being loaded to the toolhead

dense sequoia Nov 29, 2024, 5:11 PM

#

{"result": {"eventtime": 194.389744273, "status": {"AFC return": {}}}}

#

thats the query return

stable meadow Nov 29, 2024, 5:12 PM

#

<yourprinterip>/printer/objects/query?AFC

#

replace <yourprinterip> obviously

hidden plank Nov 29, 2024, 5:12 PM

#

yeah, sorry 😄

dense sequoia Nov 29, 2024, 5:12 PM

#

correct

hidden plank Nov 29, 2024, 5:12 PM

#

drop the ' return' at the end

dense sequoia Nov 29, 2024, 5:13 PM

#

{"result": {"eventtime": 322.617114048, "status": {"AFC": {"Turtle_1": {"leg1": {"LANE": 1, "Command": null, "load": false, "prep": true, "loaded_to_hub": false, "material": "", "spool_id": "", "color": "#000000", "weight": 0}, "leg2": {"LANE": 2, "Command": null, "load": false, "prep": false, "loaded_to_hub": false, "material": "", "spool_id": "", "color": "#000000", "weight": 0}, "leg3": {"LANE": 3, "Command": null, "load": false, "prep": false, "loaded_to_hub": false, "material": "", "spool_id": "", "color": "#000000", "weight": 0}, "leg4": {"LANE": 4, "Command": null, "load": false, "prep": false, "loaded_to_hub": false, "material": "", "spool_id": "", "color": "#000000", "weight": 0}, "system": {"type": "Box_Turtle", "hub_loaded": false, "can_cut": true, "screen": "None"}}, "system": {"current_load": null, "num_units": 1, "num_lanes": 4, "num_extruders": 1, "extruders": {"extruder": {"lane_loaded": "leg1", "tool_start_sensor": false, "tool_end_sensor": false, "buffer": "TN2", "buffer_status": "Advancing"}}}}}}}

hidden plank Nov 29, 2024, 5:14 PM

#

{
  "result": {
    "eventtime": 322.617114048,
    "status": {
      "AFC": {
        "Turtle_1": {
          "leg1": {
            "LANE": 1,
            "Command": null,
            "load": false,
            "prep": true,
            "loaded_to_hub": false,
            "material": "",
            "spool_id": "",
            "color": "#000000",
            "weight": 0
          },
          "leg2": {
            "LANE": 2,
            "Command": null,
            "load": false,
            "prep": false,
            "loaded_to_hub": false,
            "material": "",
            "spool_id": "",
            "color": "#000000",
            "weight": 0
          },
          "leg3": {
            "LANE": 3,
            "Command": null,
            "load": false,
            "prep": false,
            "loaded_to_hub": false,
            "material": "",
            "spool_id": "",
            "color": "#000000",
            "weight": 0
          },
          "leg4": {
            "LANE": 4,
            "Command": null,
            "load": false,
            "prep": false,
            "loaded_to_hub": false,
            "material": "",
            "spool_id": "",
            "color": "#000000",
            "weight": 0
          },
          "system": {
            "type": "Box_Turtle",
            "hub_loaded": false,
            "can_cut": true,
            "screen": "None"
          }
        },
        "system": {
          "current_load": null,
          "num_units": 1,
          "num_lanes": 4,
          "num_extruders": 1,
          "extruders": {
            "extruder": {
              "lane_loaded": "leg1",
              "tool_start_sensor": false,
              "tool_end_sensor": false,
              "buffer": "TN2",
              "buffer_status": "Advancing"
            }
          }
        }
      }
    }
  }
}

prettied up

#

"tool_start_sensor": false,
"tool_end_sensor": false,

#

you say it's loaded all the way to the extruder?

#

your lane 1 extruder and hub also don't see the filament

dense sequoia Nov 29, 2024, 5:17 PM

#

Its loaded ... i going to reboot and try T0 one more time

#

I didn t have near this much trouble building both Vorons

#

{"result": {"eventtime": 342.557711666, "status": {"AFC": {"Turtle_1": {"leg1": {"LANE": 1, "Command": null, "load": true, "prep": true, "loaded_to_hub": true, "material": "", "spool_id": "", "color": "#000000", "weight": 0}, "leg2": {"LANE": 2, "Command": null, "load": false, "prep": false, "loaded_to_hub": false, "material": "", "spool_id": "", "color": "#000000", "weight": 0}, "leg3": {"LANE": 3, "Command": null, "load": false, "prep": false, "loaded_to_hub": false, "material": "", "spool_id": "", "color": "#000000", "weight": 0}, "leg4": {"LANE": 4, "Command": null, "load": false, "prep": false, "loaded_to_hub": false, "material": "", "spool_id": "", "color": "#000000", "weight": 0}, "system": {"type": "Box_Turtle", "hub_loaded": true, "can_cut": true, "screen": "None"}}, "system": {"current_load": null, "num_units": 1, "num_lanes": 4, "num_extruders": 1, "extruders": {"extruder": {"lane_loaded": "leg1", "tool_start_sensor": true, "tool_end_sensor": false, "buffer": "TN2", "buffer_status": "Advancing"}}}}}}}

hidden plank Nov 29, 2024, 5:24 PM

#

that second one looks more correct

dense sequoia Nov 29, 2024, 5:25 PM

#

Turtle_1 Status
LANE | Prep | Load | Hub | Tool |
LEG1 | <--> | <--> |  x  |  xx  |
LEG2 |  xx  |  xx  |  x  |  xx  |
LEG3 |  xx  |  xx  |  x  |  xx  |
LEG4 |  xx  |  xx  |  x  |  xx  |
12:24 PM
afc_status
12:21 PM
FAILED TO LOAD LEG1 TO TOOL, CHECK FILAMENT PATH```

hidden plank Nov 29, 2024, 5:25 PM

#

what are the contenst of ~/printer_data/config/AFC/AFC.var.unit and AFC.var.tool

#

also, did you do BT_LANE_MOVE to get the filaemtn to the toolhead?

#

if so, retract it all back out before doign T0

stable meadow Nov 29, 2024, 5:33 PM

#

"loaded_to_hub": true,

#

hub switch is doing stuff

#

❤️

dense sequoia Nov 29, 2024, 5:46 PM

#

now i need to figure out the sanppy thing

#

stable meadow Nov 29, 2024, 5:51 PM

#

dense sequoia

when is this happening?

#

like uh during what action

lean zealot Nov 29, 2024, 5:53 PM

#

Looks like an eject?

dense sequoia Nov 29, 2024, 5:53 PM

#

yes ..is that the wrong way to re-wind

frank forge Nov 29, 2024, 5:55 PM

#

i dont' think eject doesn rewind, it just spits it out

#

if you have something loaded to the toolhead you want to unload toolhead iirc

lean zealot Nov 29, 2024, 5:57 PM

#

Eject does a rewind now

#

Eject does a rewind until the LOAD switch is untriggered

dense sequoia Nov 29, 2024, 6:01 PM

#

that was running eject

hidden plank Nov 29, 2024, 6:12 PM

#

eject dcoesn't respool it

#

so manually rewind, then heat to temp (175 seems really low to me for pla, which is what i've seen you using) - would recommend 210

#

then try a t0

dense sequoia Nov 29, 2024, 6:22 PM

#

ok

#

Im looking for ther temp ..175 is thge default

hidden plank Nov 29, 2024, 6:36 PM

#

yes, but that is the 'fallback'temperature

#

minimum safe

#

you can set it higher then do the Tx commands, it iwll not lower it to 175...

#

this is not a problem during regualry printing because your slicer sends teh temperature commands

dense sequoia Nov 29, 2024, 6:37 PM

#

make sense

#

v0.0.0-789 > v0.0.0-818 another update ?

hidden plank Nov 29, 2024, 6:38 PM

#

there's alwaysa nother update 😄

#

these ones rae less dangerous though

#

more minor bug fixes

dense sequoia Nov 29, 2024, 6:38 PM

#

ok

white igloo Nov 29, 2024, 6:39 PM

#

Just don't re-run the install script at the moment 🙂

dense sequoia Nov 29, 2024, 6:39 PM

#

oh no

#

I have enough issues atm

hidden plank Nov 29, 2024, 6:40 PM

#

you don't have to update

#

if you have not

dense sequoia Nov 29, 2024, 6:40 PM

#

I didnt

hidden plank Nov 29, 2024, 6:40 PM

#

then just try heating to 210C ont eh toolhead and then do a T0

#

wait

#

are you doing pla or abs

dense sequoia Nov 29, 2024, 6:41 PM

#

pla

hidden plank Nov 29, 2024, 6:41 PM

#

ok

dense sequoia Nov 29, 2024, 6:41 PM

#

4 spols of PLA loadded

hidden plank Nov 29, 2024, 6:42 PM

#

I'm sorry for not catching this early

#

but tryign to extrude at 175C is probably like all of your clog/doesn't extrude issues

#

I do pla at 220-230C for printing most of hte time

dense sequoia Nov 29, 2024, 6:42 PM

#

I changed the temps to 230

#

when extruding

#

i know 175 too cold

#

id like to get at least 1 leg printing today if possible

hidden plank Nov 29, 2024, 6:44 PM

#

that would be amazing

dense sequoia Nov 29, 2024, 6:45 PM

#

yea Im sure

#

Going to try and print a 1st layer

#

filaemt not making to to the tool head sensor again

hidden plank Nov 29, 2024, 7:02 PM

#

video of what happens when you do a T0 please

#

'not making it toolhead' is too vague

#

eject the lane, insert filament, heat to temp. then start a video and do a T0 and follow the filament path and keep it going until it errors out

dense sequoia Nov 29, 2024, 7:13 PM

#

rn_image_picker_lib_temp_713306ed-e6d9-44cd-a2bc-fe2e40cc856a.jpg

#

Kinda hard to see

stable meadow Nov 29, 2024, 7:14 PM

#

stopping just shy of the sensor it looks like?

dense sequoia Nov 29, 2024, 7:14 PM

#

yep

#

bowden length at 1430 / sensor too tip of nozzle set to 172

hidden plank Nov 29, 2024, 7:16 PM

#

that'snot a video mike 😄

dense sequoia Nov 29, 2024, 7:16 PM

#

yes i know Im trying to get it unloaded

hidden plank Nov 29, 2024, 7:16 PM

#

ok

dense sequoia Nov 29, 2024, 7:16 PM

#

wont unload

hidden plank Nov 29, 2024, 7:16 PM

#

how many short moves does it do

dense sequoia Nov 29, 2024, 7:16 PM

#

5-6

hidden plank Nov 29, 2024, 7:17 PM

#

set bowden length to like 1470 then

dense sequoia Nov 29, 2024, 7:23 PM

#

filament justr will not unload

#

using eject again to get it out

#

stuck it crashed kliipper

#

this is jsut crazy

lean zealot Nov 29, 2024, 7:25 PM

#

BT_TOOL_UNLOAD will not unload unless it gets to the tool head sensor

dense sequoia Nov 29, 2024, 7:25 PM

#

I think Ive had enough

#

Just too many issue

#

Thanks for trying though ...3+ weeks of issue's is just too much

hidden plank Nov 29, 2024, 8:11 PM

#

I just don't understand how you are trying to unload filament and where there are so many problems if you don't even have it to thte extrduer gears yet

#

as belial said you can't use the unload tool macro unless it got loaded in the first place, which it did not. so you have to do a BT_LANE_MOVE or BT_LANE_EJECT, and try again

dense sequoia Dec 3, 2024, 11:07 PM

#

Ok got filament to the tool head and auto did a nozzle clean then park after hitting T0

#

Trying to print see what happens

#

QGL ..sorry for the step by step

dense sequoia Dec 3, 2024, 11:38 PM

#

When print job started spool just chirping

#

1st print

#

I can see the filament jumping up and down a bit

lucid acorn Dec 3, 2024, 11:53 PM

#

Is your buffer fully expanded by chance?

dense sequoia Dec 3, 2024, 11:55 PM

#

rn_image_picker_lib_temp_dcc03562-eb3b-40dd-b864-e49371bc3198.jpg

#

rn_image_picker_lib_temp_cd03a535-ed01-4044-8d79-58ad71bb194e.jpg

#

Other angle

frank forge Dec 3, 2024, 11:59 PM

#

looks like it

dense sequoia Dec 3, 2024, 11:59 PM

#

Is that good or bad ?

lucid acorn Dec 4, 2024, 12:01 AM

#

that is not good, query the buffer QUERY_BUFFER BUFFER={buffer name}

#

what does that say?

dense sequoia Dec 4, 2024, 12:01 AM

#

Rebooting waiting on klipper to reconnect

lucid acorn Dec 4, 2024, 12:02 AM

#

I'm sure you have before but drop your AFC_buffer section

dense sequoia Dec 4, 2024, 12:03 AM

#

Whatcha mean drop ?

lucid acorn Dec 4, 2024, 12:03 AM

#

sorry paste or screenshot it and put it here

#

should look like this

dense sequoia Dec 4, 2024, 12:04 AM

#

advance_pin: !turtleneck:ADVANCE
trailing_pin: !turtleneck:TRAILING
multiplier_high: 1.05   # default 1.05, factor to feed more filament
multiplier_low:  0.95   # default 0.95, factor to feed less filament
led_index: Buffer_Indicator:1
velocity: 100```

lucid acorn Dec 4, 2024, 12:06 AM

#

okay that looks good

#

what does the query show?

#

QUERY_BUFFER BUFFER=TN2

dense sequoia Dec 4, 2024, 12:07 AM

#

LEG1 Rotation distance: 4.428571428571429

lucid acorn Dec 4, 2024, 12:08 AM

#

and it's fully expanded

#

?

dense sequoia Dec 4, 2024, 12:08 AM

#

looks like it

#

lucid acorn Dec 4, 2024, 12:10 AM

#

it looks like the extra piece you have in there plus the spring is not allowing it to travel far enough to the advance trigger.

dense sequoia Dec 4, 2024, 12:10 AM

#

the spring retainer

lucid acorn Dec 4, 2024, 12:11 AM

#

Yes

#

Needs to be able to fully expand

dense sequoia Dec 4, 2024, 12:12 AM

#

ok let me eject the filament

lucid acorn Dec 4, 2024, 12:13 AM

#

lucid acorn Yes

#

You can expand the this part so it doesn’t get stuck in the hole

dense sequoia Dec 4, 2024, 12:13 AM

#

now filament wont unload and I heated to 220

lucid acorn Dec 4, 2024, 12:14 AM

#

TOOL_UNLOAD doesn't unload the lane?

#

is it giving you an error?

dense sequoia Dec 4, 2024, 12:15 AM

#

No error

#

rn_image_picker_lib_temp_0e8d9c69-0a92-4928-ad25-ee0217d50cc3.jpg

#

Soon as I hit bt unload it chirped two times

lucid acorn Dec 4, 2024, 12:16 AM

#

<@&1304550334839918672> thoughts on this everyone?

#

I would remove the spring retainer but you will have to get it unloaded first

desert heron Dec 4, 2024, 12:17 AM

#

stalled stepper?

dense sequoia Dec 4, 2024, 12:17 AM

#

not sure

lean zealot Dec 4, 2024, 12:18 AM

#

what does AFC_STATUS report?

dense sequoia Dec 4, 2024, 12:18 AM

#

7:18 PM
Turtle_1 Status
LANE | Prep | Load | Hub | Tool |
LEG1 | <--> | <--> | <-> | xx |
LEG2 | <--> | <--> | x | xx |
LEG3 | <--> | <--> | x | xx |
LEG4 | <--> | <--> | x | xx |

lean zealot Dec 4, 2024, 12:18 AM

#

You need to run eject on lane 1, if it's in your toolhead manually unlatch it

#

It's not aware of a lane being fully loaded

dense sequoia Dec 4, 2024, 12:19 AM

#

I did run eject

#

7:19 PM
LANE leg1 IS TOOL LOADED
7:19 PM
BT_LANE_EJECT LANE=1

#

bt move worked

lean zealot Dec 4, 2024, 12:20 AM

#

interesting

lucid acorn Dec 4, 2024, 12:20 AM

#

It seems that it is still in the toolhead but the sensor is not seeing it

dense sequoia Dec 4, 2024, 12:21 AM

#

lean zealot Dec 4, 2024, 12:21 AM

#

Hey Mike, can you zip your configs and send em?

dense sequoia Dec 4, 2024, 12:21 AM

#

yes

lucid acorn Dec 4, 2024, 12:22 AM

#

do you have the toolhead sensor showing in mainsail as well?

dense sequoia Dec 4, 2024, 12:22 AM

#

📎 config-20241203-192203.zip

#

7:19 PM
LANE leg1 IS TOOL LOADED
7:19 PM
BT_LANE_EJECT LANE=1
7:19 PM
Extrude below minimum temp
7:19 PM
Extrude below minimum temp
See the 'min_extrude_temp' config option for details
7:19 PM
Extrude below minimum temp

#

filament out

lucid acorn Dec 4, 2024, 12:25 AM

#

Change the bottom of your AFC_hardware.cfg to this:

pins: AFC:HUB, sb2040:gpio29

[filament_switch_sensor AFC_Hub_Sensor]
switch_pin: ^AFC:HUB
pause_on_runout: False

[filament_switch_sensor AFC_Tool_Sensor]
switch_pin: sb2040:gpio29
pause_on_runout: False```

#

This will allow you to see the toolhead sensor in mainsail

lucid acorn Dec 4, 2024, 12:25 AM

#

dense sequoia filament out

it unloaded?

dense sequoia Dec 4, 2024, 12:25 AM

#

yes

lucid acorn Dec 4, 2024, 12:25 AM

#

What did you end up doing that got it unloaded?

dense sequoia Dec 4, 2024, 12:30 AM

#

bt move

#

T0

#

did nothing vnow

#

T0 running now

#

spring fullycompressed again

#

ounce it hit the tool head I can see it compress slow then it goes fully compressed

lean zealot Dec 4, 2024, 12:37 AM

#

What does your Toolhead sensor report?

dense sequoia Dec 4, 2024, 12:38 AM

#

M
Turtle_1 Status
LANE | Prep | Load | Hub | Tool |
LEG1 | <--> | <--> | <-> | <--> |
LEG2 | <--> | <--> | x | xx |
LEG3 | <--> | <--> | x | xx |
LEG4 | <--> | <--> | x | xx |

lean zealot Dec 4, 2024, 12:39 AM

#

Tool is loaded then.

dense sequoia Dec 4, 2024, 12:39 AM

#

yes

#

fiilament is passed the filament sensor and in the g2e that i can see of

lucid acorn Dec 4, 2024, 12:41 AM

#

Were you able to get the spring retainer removed?

dense sequoia Dec 4, 2024, 12:41 AM

#

yes

lucid acorn Dec 4, 2024, 12:41 AM

#

What does the buffer query show?

dense sequoia Dec 4, 2024, 12:41 AM

#

7:41 PM
TN2 : Advancing
LEG1 Rotation distance: 4.428571428571429

lucid acorn Dec 4, 2024, 12:41 AM

#

And its neck is fully expanded?

dense sequoia Dec 4, 2024, 12:42 AM

#

yes

#

spring compressed to the max

lucid acorn Dec 4, 2024, 12:43 AM

#

Hmm we’re getting close.

#

Another pic?

dense sequoia Dec 4, 2024, 12:43 AM

#

rn_image_picker_lib_temp_8ee3f63b-0fc6-4ec2-8787-8e94fafb7c20.jpg

#

rn_image_picker_lib_temp_05565608-5f3f-4b67-8f52-ebaa1a72a4a4.jpg

lucid acorn Dec 4, 2024, 12:51 AM

#

Let’s try unloading again and moving the buffer manually to check its states

dense sequoia Dec 4, 2024, 12:52 AM

#

ok

#

now bt unload is sqealing

lucid acorn Dec 4, 2024, 12:57 AM

#

Is it clearing your toolhead sensor before it does the long move?

dense sequoia Dec 4, 2024, 12:57 AM

#

as in loading ?

lucid acorn Dec 4, 2024, 12:58 AM

#

So it should do a synced move to pull the silent clear of the toolhead sensor then a long move back to BT

dense sequoia Dec 4, 2024, 12:58 AM

#

does -2-3 short burst before entering filament sensor

lucid acorn Dec 4, 2024, 12:58 AM

#

What does it do when it is unloading?

dense sequoia Dec 4, 2024, 12:59 AM

#

nothing now

#

Rebooted now its ejecting slowly

#

I dont think that is correct either

lucid acorn Dec 4, 2024, 1:23 AM

#

At dinner but you’re so close!

dense sequoia Dec 4, 2024, 1:28 AM

#

👍

dense sequoia Dec 4, 2024, 2:09 AM

#

ill wait

lucid acorn Dec 4, 2024, 3:12 AM

#

lucid acorn Change the bottom of your AFC_hardware.cfg to this: ```[duplicate_pin_override] ...

#

Let’s circle back here so we can watch for the toolhead sensor. It seems like it’s not being reliable.

dense sequoia Dec 4, 2024, 11:28 AM

#

👍

dense sequoia Dec 4, 2024, 9:33 PM

#

#

lets see what happens

#

T0 then goes 2-3 short bursts to the tool head then I hear the TN2 make it 2 moves then its now al l he way in not sticking out

lucid acorn Dec 4, 2024, 9:39 PM

#

So buffer is not fully expanded?

dense sequoia Dec 4, 2024, 9:41 PM

#

inside of the box

#

I think I need to print a short diffuser to hold the ptfe more straight up

dense sequoia Dec 6, 2024, 1:06 AM

#

Lets see what Happens

lean zealot Dec 6, 2024, 1:07 AM

#

slamdesk

dense sequoia Dec 6, 2024, 1:17 AM

#

failed bed will not pass QGL now

lean zealot Dec 6, 2024, 1:17 AM

#

Too many retries or what?

dense sequoia Dec 6, 2024, 1:17 AM

#

too many retries

lean zealot Dec 6, 2024, 1:18 AM

#

Restart your host and try again

dense sequoia Dec 6, 2024, 1:18 AM

#

0.3

#

mostly

#

finally after 8 tries

#

Now running qgl again front to back diagonal

#

Going to fail

#

Failed

cyan shuttle Dec 6, 2024, 1:28 AM

#

What probe do you have mike

dense sequoia Dec 6, 2024, 1:29 AM

#

tap v2 choatic labs

cyan shuttle Dec 6, 2024, 1:33 AM

#

Nozzle nice and clean?

#

What do you have your tolerance set to?

lucid acorn Dec 6, 2024, 1:35 AM

#

are you at temp or heating up?

dense sequoia Dec 6, 2024, 1:37 AM

#

#

going to fail again

#

7 of 8 now

stable meadow Dec 6, 2024, 1:38 AM

#

what probe are you using

dense sequoia Dec 6, 2024, 1:38 AM

#

CL TAP v2

#

timer to close now rebooting

#

Retries: 2/8 Probed points range: 0.002500 tolerance: 0.007500

cyan shuttle Dec 6, 2024, 1:44 AM

#

That doesnt make any sense.

dense sequoia Dec 6, 2024, 1:45 AM

#

yes thats manual QGL

cyan shuttle Dec 6, 2024, 1:45 AM

#

is your bed loose?

dense sequoia Dec 6, 2024, 1:45 AM

#

no

#

its on the 2nd QGL after hitting print

lean zealot Dec 6, 2024, 1:45 AM

#

Is any part of your tool head loose?

cyan shuttle Dec 6, 2024, 1:46 AM

#

You dont need to QGL 2x

dense sequoia Dec 6, 2024, 1:46 AM

#

i understand

#

i hit home /qgl

#

then I hit print ..then it runa QGL after hitting 150 then Front left to back Right

cyan shuttle Dec 6, 2024, 1:47 AM

#

Diagonally?

#

Never seen that

dense sequoia Dec 6, 2024, 1:47 AM

#

yes

#

only o nthe Box turtle serial print

cyan shuttle Dec 6, 2024, 1:48 AM

#

Mine just goes around the 4 points until its happy and continues on.

dense sequoia Dec 6, 2024, 1:48 AM

#

ill make a vid

#

mine does the 4 corners if i hit the QGL next to the home button

#

Sorry watching turtle video in back ground

#

Never seen it do that after hitting print

#

Now it's bed leveling diagonal

#

its foobarred

cyan shuttle Dec 6, 2024, 1:58 AM

#

Discord seems to be having issues with media, I cant get your videos to load.

dense sequoia Dec 6, 2024, 1:59 AM

#

not moving any filament

#

im ready to rename my name to " I have no clue what I'm doing"

cyan shuttle Dec 6, 2024, 2:05 AM

#

Did one of your A/B motors go out?

#

Or does it move normally otherwise?

dense sequoia Dec 6, 2024, 2:07 AM

#

let me reboot

#

ill test the home / qgl

#

Yea guess motor dead

#

Only diagonal qgl

#

That explains it

lean zealot Dec 6, 2024, 2:12 AM

#

Do you home normally?

dense sequoia Dec 6, 2024, 2:13 AM

#

yes home fine

lean zealot Dec 6, 2024, 2:13 AM

#

then something is funky in your QGL all of a sudden if all other motion is normal

dense sequoia Dec 6, 2024, 2:13 AM

#

qill just order new motors ..ill be back in a couple weeks

cyan shuttle Dec 6, 2024, 2:14 AM

#

No dont do that.

#

Its gotta be something in config if it homes fine.

dense sequoia Dec 6, 2024, 2:15 AM

#

nothing changed in config

cyan shuttle Dec 6, 2024, 2:17 AM

#

Are you able to move the toolhead around normally using the X/Y controls after homing?

dense sequoia Dec 6, 2024, 2:18 AM

#

manual move tool head by hand only moving diag too

lean zealot Dec 6, 2024, 2:19 AM

#

Check wiring or your stepper driver first then

dense sequoia Dec 6, 2024, 2:19 AM

#

so something broke

lean zealot Dec 6, 2024, 2:19 AM

#

Stepper motors don't usually just die like that, they're pretty resilient

stable meadow Dec 6, 2024, 2:20 AM

#

STEPPER_BUZZ STEPPER=stepper_x

STEPPER_BUZZ STEPPER=stepper_y

#

you can visually determine if the shaft moves etc

maybe a grub came loose or something (happened to me)

dense sequoia Dec 6, 2024, 2:20 AM

#

Y moving backwards tool head moving to x

#

almost like its total racked

lean zealot Dec 6, 2024, 2:22 AM

#

Motor isn't locked up, that moved way too smoothly diagonally

#

or wait, brain

#

Can you look down on the top and when you make an X or Y move see if a motor shaft spins separate from the gear?

dense sequoia Dec 6, 2024, 2:26 AM

#

I found the issue

lean zealot Dec 6, 2024, 2:26 AM

#

Yeees?

dense sequoia Dec 6, 2024, 2:27 AM

#

checked my back up print config ....I dont know how this happened but he enable pin was missing the !

lean zealot Dec 6, 2024, 2:27 AM

#

See! Nothing major!

dense sequoia Dec 6, 2024, 2:27 AM

#

but why would have that have been removed.

#

only thing I did was update klipper

cyan shuttle Dec 6, 2024, 2:29 AM

#

Who knows what happens when you update klipper

dense sequoia Dec 6, 2024, 2:30 AM

#

Retries: 1/8 Probed points range: 0.002500 tolerance: 0.007500

lean zealot Dec 6, 2024, 2:30 AM

#

Oh, that's why, you updated Klipper

#

Never do that

dense sequoia Dec 6, 2024, 2:30 AM

#

ok

cyan shuttle Dec 6, 2024, 2:30 AM

#

https://tenor.com/view/michael-scott-the-office-theoffice-gif-25837061

Tenor

dense sequoia Dec 6, 2024, 2:31 AM

#

now to figure out why filament not extruding

lean zealot Dec 6, 2024, 2:31 AM

#

What's your nozzle temp at?

dense sequoia Dec 6, 2024, 2:31 AM

#

220

#

i manually upped it too that

lean zealot Dec 6, 2024, 2:32 AM

#

Does the turtle have the filament loaded?

#

and does AFC_Status report as much?

dense sequoia Dec 6, 2024, 2:33 AM

#

#

9:33 PM
Turtle_1 Status
LANE | Prep | Load | Hub | Tool |
LEG1 | <--> | <--> | x | xx |
LEG2 | <--> | <--> | x | xx |
LEG3 | <--> | <--> | x | xx |
LEG4 | <--> | <--> | x | xx |

#

there is my issue

lean zealot Dec 6, 2024, 2:33 AM

#

Yep

dense sequoia Dec 6, 2024, 2:33 AM

#

klipper says its loaded but afc says no

lean zealot Dec 6, 2024, 2:34 AM

#

Klipper is just showing switch states

#

AFC needs to know it's loaded or nothing will happen

dense sequoia Dec 6, 2024, 2:35 AM

#

-ejected ...reloading T0

#

back to hub not working \

#

9:37 PM
Turtle_1 Status
LANE | Prep | Load | Hub | Tool |
LEG1 | <--> | <--> | x | xx |
LEG2 | <--> | <--> | x | xx |
LEG3 | <--> | <--> | x | xx |
LEG4 | <--> | <--> | x | xx |

#

AFC Hub Sensor
detected

#

AFC Tool Sensor
detected

#

i dont get it

lean zealot Dec 6, 2024, 2:39 AM

#

eject it, reload and take a video of the whole load

dense sequoia Dec 6, 2024, 2:42 AM

#

Loud pop was the ecas being popped out

#

Ill have to reinsert it 1st it has done that

#

rn_image_picker_lib_temp_422dfe54-4bf5-4a06-9c20-cb2f901796d0.jpg

lean zealot Dec 6, 2024, 2:51 AM

#

I keep forgetting you're on G2E...

#

@cyan shuttle you're up for G2E stuff

cyan shuttle Dec 6, 2024, 2:52 AM

#

Cry

#

OK

dense sequoia Dec 6, 2024, 2:52 AM

#

yes

#

g2e

cyan shuttle Dec 6, 2024, 2:53 AM

#

Yeah that sounds about right.

#

mine used to do crazy crap like that

#

The filament is getting stuck somewhere around the big extruder wheel more than likely.

dense sequoia Dec 6, 2024, 2:54 AM

#

ican open it up more

#

tension screw only 1 turn when inserted

cyan shuttle Dec 6, 2024, 2:57 AM

#

Ok, was the filament stuck there?

dense sequoia Dec 6, 2024, 2:57 AM

#

noped ecas poppeed out again

#

guess the hub cutter part wil lhave to be re -pritned

cyan shuttle Dec 6, 2024, 2:58 AM

#

No.

#

Something is causing a ton of tension thats why its popping out

#

We need to figure out what

#

Is it jamming in the extruder/hot end?

dense sequoia Dec 6, 2024, 2:59 AM

#

its making it that far i can see the filament going passed the tool sensor

#

let me make a vid for whan it gets close to the toolhead

#

lean zealot Dec 6, 2024, 3:06 AM

#

It never picked up the toolhead sensor triggered...

dense sequoia Dec 6, 2024, 3:06 AM

#

AFC Hub Sensor
detected
AFC Tool Sensor
detected

lean zealot Dec 6, 2024, 3:07 AM

#

Unload the filament

dense sequoia Dec 6, 2024, 3:07 AM

#

Now it's running qgl on it own

#

📎 message.txt

#

that was after hittingh T0

#

Ill unload

cyan shuttle Dec 6, 2024, 3:13 AM

#

It sounded like it did, it switched to the tool_stn move I thought I heard

dense sequoia Dec 6, 2024, 3:14 AM

#

Tried extruding...nothing

#

possiable nozzle clogged

cyan shuttle Dec 6, 2024, 3:20 AM

#

So, again, is it jammed in the extruder or hot end?

dense sequoia Dec 6, 2024, 3:21 AM

#

appears

#

maybe i should bit e the bullet and get a different extruder/hotend

#

😀

frank forge Dec 6, 2024, 3:28 AM

#

I mean CW2 is pretty cheap lol

lean zealot Dec 6, 2024, 3:28 AM

#

CW2 has been super reliable for me

frank forge Dec 6, 2024, 3:28 AM

#

what hot end do you have?

lean zealot Dec 6, 2024, 3:28 AM

#

And you likely have the parts for it laying around

dense sequoia Dec 6, 2024, 3:28 AM

#

rapido v2 uhf

lean zealot Dec 6, 2024, 3:29 AM

#

That's fiiine

frank forge Dec 6, 2024, 3:29 AM

#

isn't there a mount for that?

lean zealot Dec 6, 2024, 3:29 AM

#

YEs

frank forge Dec 6, 2024, 3:29 AM

#

the Rapido is a sweet hot end I don't think you need to change it

lean zealot Dec 6, 2024, 3:29 AM

#

Even a Filametrix mount for it

frank forge Dec 6, 2024, 3:29 AM

#

thats' what I thought

#

CW2 just uses the same parts the BT uses lol

lean zealot Dec 6, 2024, 3:29 AM

#

So if you wanted to do toolhead cutter, those files are all available

frank forge Dec 6, 2024, 3:29 AM

#

for the most part

lean zealot Dec 6, 2024, 3:29 AM

#

Nope, literally all the same parts

frank forge Dec 6, 2024, 3:29 AM

#

that's what I thought

lean zealot Dec 6, 2024, 3:30 AM

#

BMG gears, a pancake extruder, and a couple of D2F switches would move everything inside the toolhead

frank forge Dec 6, 2024, 3:30 AM

#

yeah super simple

#

and effective

#

oh you need 5.5mm bearings? maybe? idk

lean zealot Dec 6, 2024, 3:31 AM

#

The problem with G2E is you have to be super straight with the gears to get it to load, and then it likes to crush filament

frank forge Dec 6, 2024, 3:31 AM

#

mine has them....lol

lean zealot Dec 6, 2024, 3:31 AM

#

It's a fantastic extruder for single filaments

#

Just not great for multi material stuff

dense sequoia Dec 6, 2024, 3:33 AM

#

yea maybe this weekend I ll have to reprint the cw2 parts

cyan shuttle Dec 6, 2024, 3:34 AM

#

Yeah for stealthburner you only need to change the extruder part.

lean zealot Dec 6, 2024, 3:34 AM

#

If you want to do Filametrix cutter, lmk, we've got links to the appropriate stuff for your hot end

dense sequoia Dec 6, 2024, 3:35 AM

#

sure why not

lean zealot Dec 6, 2024, 3:35 AM

#

One moment then

dense sequoia Dec 6, 2024, 3:35 AM

#

im not getting anywhere with this stuff

lean zealot Dec 6, 2024, 3:35 AM

#

https://www.printables.com/model/816579-ercf-v2-filament-cutter-stealthburner-rapido-v2-ho/files

Printables.com

ERCF v2 Filament Cutter - Stealthburner Rapido V2 Hotend by Ianryen...

Minor edit to the Rapido ERF Filament Cutting Stealthburner Hotend to support Rapido V2 | Download free 3D printable STL models

frank forge Dec 6, 2024, 3:36 AM

#

literally everyone is using filametrix, so it's definitely going to be easier lol

lean zealot Dec 6, 2024, 3:36 AM

#

Yep

#

Super duper consistent with stuff

dense sequoia Dec 6, 2024, 3:36 AM

#

is that one for the UHF

sage cradle Dec 6, 2024, 3:36 AM

#

frank forge oh you need 5.5mm bearings? maybe? idk

He has them. He said he would have given me them if I was closer. Because I had something he needed

frank forge Dec 6, 2024, 3:37 AM

#

ah good, I think there is a version that doesn't need them though?

#

honestly kinda wish it used the MR63's and the D2HW's cause they just feel nicer lol, but the bearings work too

lean zealot Dec 6, 2024, 3:37 AM

#

dense sequoia is that one for the UHF

I thought this one had said it was, but it sure doesn't look it

#

https://www.printables.com/model/826480-filametrix-body-cw2-for-sb2209sb2240-with-dual-fil

Printables.com

Filametrix Body (CW2) for SB2209/SB2240 with Dual Filament Sensors ...

An updated Clockwork 2 body for use with the Filametrix filament cutting system and the BigTreeTech SB2209/SB2240 boards | Download free 3D printable STL models

#

https://www.printables.com/model/863145-stealthburner-rapido-v2-uhf-ercf-filament-cutter

Printables.com

stealthburner Rapido v2 UHF ERCF Filament cutter by Tijmenbo | Down...

stealth burner Rapido v2 UHF ERCF Filament cutter with longer ducts | Download free 3D printable STL models

#

This one is

#

aaand it's only the front

#

god i love some of these lol

frank forge Dec 6, 2024, 3:40 AM

#

lol

#

Wish they'd throw in all the parts just so you only gotta go one plce

#

it gets confusing on what parts you need sometimes

lean zealot Dec 6, 2024, 3:40 AM

#

They aren't updating jack all on the Filametrix github

dense sequoia Dec 6, 2024, 3:41 AM

#

I have some 5.5 mm bearings

lean zealot Dec 6, 2024, 3:42 AM

#

...

#

That's dumb lol

#

hold on, assembling bits

frank forge Dec 6, 2024, 3:42 AM

#

filametrix parts are just a sprint and a cutter..... I think thunder got the grainger cutters workign I haven't messed with it yet lol

lean zealot Dec 6, 2024, 3:43 AM

#

I think, can get cheap blades on amazon as well, but I know there have been some issues with them

frank forge Dec 6, 2024, 3:43 AM

#

you can, they chip crazy easy

lean zealot Dec 6, 2024, 3:43 AM

#

📎 stealthburner_Rapido_v2_UHF_ERCF_Filament_cutter.stl 📎 SB_RapidoV2_TH_Cutting_Printhead_Rear_v1.stl

frank forge Dec 6, 2024, 3:43 AM

#

mine has a notch in it from the filament....but it's still working lol

lean zealot Dec 6, 2024, 3:43 AM

#

Okay, so these are the Rapido V2 UHF stuff

frank forge Dec 6, 2024, 3:44 AM

#

honestly I can probably mail you some cutters and springs

#

I have extras here

dense sequoia Dec 6, 2024, 3:44 AM

#

to who

lean zealot Dec 6, 2024, 3:44 AM

#

You

frank forge Dec 6, 2024, 3:44 AM

#

you lol

dense sequoia Dec 6, 2024, 3:44 AM

#

oh ok

lean zealot Dec 6, 2024, 3:44 AM

#

https://www.amazon.com/gp/product/B0CBLRNXSV/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

HARFINGTON 40pcs Exacto Knife Blades #4 Hobby Knife Replacement Bla...

The exacto blades are made from quality manganese steel, ensuring strong hardness, excellent wear resistance, and superb machinability. No rust, exquisite workmanship, processed by multiple processes, sturdy and durable, not easy to chip. 2. You will receive 40pcs durable #4 exacto blades. You...

dense sequoia Dec 6, 2024, 3:44 AM

#

let me know how much

lean zealot Dec 6, 2024, 3:44 AM

#

These are cheap af if you want to order as well

#

Like HDale said, liable to chip easily

frank forge Dec 6, 2024, 3:45 AM

#

yeah those aren't the ones I have

#

mine had like 100 or osmething in it

dense sequoia Dec 6, 2024, 3:45 AM

#

anything else i need to print for the cutter

#

or order parts for

lean zealot Dec 6, 2024, 3:46 AM

#

Still gathering bits, one second lol

#

You have 5.5mm bearings and D2F switches, right?

frank forge Dec 6, 2024, 3:46 AM

#

shoot me $5 for shipping and I'll throw in a couple springs and a bunch of blades, or you can just get them from amazon for like $10 I think

dense sequoia Dec 6, 2024, 3:46 AM

#

DM me

lean zealot Dec 6, 2024, 3:46 AM

#

frank forge Dec 6, 2024, 3:46 AM

#

https://www.amazon.com/dp/B0C33B7ZK1?ref=ppx_yo2ov_dt_b_fed_asin_title

uxcell Compression Spring, 5Pcs 304 Stainless Steel, 4mm OD, 0.4mm ...

uxcell Compression Spring, 5Pcs 304 Stainless Steel, 4mm OD, 0.4mm Wire Size, 15mm Free Length, Silver Tone

lean zealot Dec 6, 2024, 3:46 AM

#

oh lord, which spring now lol

frank forge Dec 6, 2024, 3:46 AM

#

yeah

#

that's the ones I ordered

#

so like $10 from amazon for both

lean zealot Dec 6, 2024, 3:47 AM

#

Yep

frank forge Dec 6, 2024, 3:47 AM

#

https://www.amazon.com/dp/B07QP8L1QG?ref=ppx_yo2ov_dt_b_fed_asin_title these are the blades I got......they work ok but they chip easy

TIHOOD 100PCS #4 Replacement Hobby Blade/Steel Craft Knife Blades

#

if you have a grainger over there I'd go for those if they work. @hidden plank?

lean zealot Dec 6, 2024, 3:51 AM

#

📎 Filametrix_Rapido_V2_UHF.zip

#

Okay, this should be everything you need to print for Filametrix to work now

hidden plank Dec 6, 2024, 3:52 AM

#

They work great

dense sequoia Dec 6, 2024, 3:52 AM

#

thanks ..ill get started on it

frank forge Dec 6, 2024, 3:52 AM

#

definitely look for a grainger then, they got em on the shelf over here

#

was like $7 and japenese blades

dense sequoia Dec 6, 2024, 3:53 AM

#

i have a grainger about 45 to hour from me

frank forge Dec 6, 2024, 3:53 AM

#

well they can ship too lol

dense sequoia Dec 6, 2024, 3:53 AM

#

is there a part #

frank forge Dec 6, 2024, 3:53 AM

#

sec

#

https://www.grainger.com/product/OLFA-Chisel-Art-Blade-5-16-in-Blade-6ZTK2?opr=HPRVP

dense sequoia Dec 6, 2024, 3:54 AM

#

ok

lean zealot Dec 6, 2024, 3:54 AM

#

This doesn't work in the blade holder I sent

#

iirc

frank forge Dec 6, 2024, 3:54 AM

#

I think the theory was it should, but thunders were overly tight for some reason?

#

but I don't recall the outcome of that

#

I know @hidden plank printed a slightly wider one

#

I want to say it just stretched it in the slicer like 1mm

hidden plank Dec 6, 2024, 3:55 AM

#

Just increase it slightly by like .1mm

frank forge Dec 6, 2024, 3:55 AM

#

ah so not even close to 1mm lol

#

andthen probably a dab of super glue.

hidden plank Dec 6, 2024, 3:56 AM

#

frank forge Dec 6, 2024, 3:57 AM

#

I need to do that and swap my blade lol

dense sequoia Dec 6, 2024, 4:02 AM

#

i just scalled the blade holder 8.4

#

3 hrs to print ...not bad

dense sequoia Dec 6, 2024, 9:37 PM

#

lean zealot This doesn't work in the blade holder I sent

is the sensor for the ballbearing switches?

lean zealot Dec 6, 2024, 9:37 PM

#

hmm?

dense sequoia Dec 6, 2024, 9:37 PM

#

I dont have anymore switches with the flag's

lean zealot Dec 6, 2024, 9:37 PM

#

No lever

#

Just D2F switch

dense sequoia Dec 6, 2024, 9:38 PM

#

so it takes ball bearing to push the switch

#

just checking before i print

lean zealot Dec 6, 2024, 9:39 PM

#

Yep, uses a 5.5mm ball bearing

dense sequoia Dec 6, 2024, 9:39 PM

#

👍

lean zealot Dec 6, 2024, 9:39 PM

#

The body I sent has both before and after extruder sensors btw

#

so 2 of those

dense sequoia Dec 6, 2024, 10:35 PM

#

yep

#

i dont think I have anymore ports o nthe sb2040

lean zealot Dec 6, 2024, 10:36 PM

#

hmm?

dense sequoia Dec 6, 2024, 10:39 PM

#

lean zealot Dec 6, 2024, 10:39 PM

#

Yeah, I have one in my hand lol

dense sequoia Dec 6, 2024, 10:39 PM

#

ok

lean zealot Dec 6, 2024, 10:40 PM

#

I'm just trying to figure out how it wouldn't work lol

cyan shuttle Dec 6, 2024, 10:40 PM

#

Are you using an X end stop on the toolhead?

lean zealot Dec 6, 2024, 10:40 PM

#

That would change it

cyan shuttle Dec 6, 2024, 10:40 PM

#

If not just use the XES port.

dense sequoia Dec 6, 2024, 10:40 PM

#

yes i am

lean zealot Dec 6, 2024, 10:40 PM

#

There's not a dedicated XES port on this technically

#

Ah

cyan shuttle Dec 6, 2024, 10:40 PM

#

Oooh.

lean zealot Dec 6, 2024, 10:40 PM

#

Have you started printing parts yet then?

dense sequoia Dec 6, 2024, 10:40 PM

#

Mo

lean zealot Dec 6, 2024, 10:40 PM

#

Okay, one moment

dense sequoia Dec 6, 2024, 10:40 PM

#

ok

frank forge Dec 6, 2024, 10:48 PM

#

your x/y endstops are on your tool head?

dense sequoia Dec 6, 2024, 10:49 PM

#

yes

cyan shuttle Dec 6, 2024, 10:49 PM

#

frank forge your x/y endstops are on your tool head?

I would assume just X.

dense sequoia Dec 6, 2024, 10:49 PM

#

yes

cyan shuttle Dec 6, 2024, 10:49 PM

#

probablysince he doesnt run a Y cable chain

#

YES on the B drive.

frank forge Dec 6, 2024, 10:50 PM

#

does the endstop connection have a spot for Y?

#

trying to look up the pinout for that thing lol

cyan shuttle Dec 6, 2024, 10:50 PM

#

Toolheads usually only have an X

frank forge Dec 6, 2024, 10:50 PM

#

mine has x and y

cyan shuttle Dec 6, 2024, 10:50 PM

#

If they have one specifically

#

Interesting.

cyan shuttle Dec 6, 2024, 10:51 PM

#

frank forge mine has x and y

Youre on a EBB format tho right? Or you were testing one?

dense sequoia Dec 6, 2024, 10:51 PM

#

let me double check

frank forge Dec 6, 2024, 10:51 PM

#

so it has 2 seperate endstop connections

#

yeah on that one there's only x but it also has a FS endstop

cyan shuttle Dec 6, 2024, 10:51 PM

#

Ive not seen a SB board with a Y end stop port

#

doesnt mean it doesnt exist.

frank forge Dec 6, 2024, 10:52 PM

#

I can show you lol

cyan shuttle Dec 6, 2024, 10:52 PM

#

I thought yuou just said you were running EBB style

frank forge Dec 6, 2024, 10:52 PM

#

#

I have the EBB one on there yes

dense sequoia Dec 6, 2024, 10:53 PM

#

I wrong ..tap v2 on tool head

frank forge Dec 6, 2024, 10:53 PM

#

but normally running nitehawk SB

dense sequoia Dec 6, 2024, 10:53 PM

#

and filadector

frank forge Dec 6, 2024, 10:53 PM

#

well you shouldn't need filatector if you are using the filametrix toolhead

dense sequoia Dec 6, 2024, 10:54 PM

#

but wouldnt that only use 1 endstop switch

cyan shuttle Dec 6, 2024, 10:54 PM

#

dense sequoia and filadector

Yeah so you wont need filatector with filametrix, so your sensor can go where filatector is wired to

frank forge Dec 6, 2024, 10:54 PM

#

you only need one currently

#

the second one isn't currently usable

dense sequoia Dec 6, 2024, 10:54 PM

#

gotcha

cyan shuttle Dec 6, 2024, 10:54 PM

#

Entry sensor is better for our application anyway

dense sequoia Dec 6, 2024, 10:54 PM

#

i was confused on the dual switch

frank forge Dec 6, 2024, 10:54 PM

#

what is the HV connection for?

cyan shuttle Dec 6, 2024, 10:54 PM

#

Yeah theyre there, but we're only gonna use the top one.

lean zealot Dec 6, 2024, 10:55 PM

#

SB2040 is layed out different than NH

frank forge Dec 6, 2024, 10:55 PM

#

has HV-IN

#

yeah I'm looking at the diagram for it lol

dense sequoia Dec 6, 2024, 10:55 PM

#

24v for sensor

lean zealot Dec 6, 2024, 10:55 PM

#

It's got 3 total end stop pins, 2 are used for XES and Tap

#

📎 Stealthburner_cw2_fil_sensor_with_ECAS_v2.stl

#

Here's one with only the pre-extruder sensor

#

You can hook this up the same way you have the one you currently have set up hooked

frank forge Dec 6, 2024, 10:56 PM

#

I really wish they'd throw a few extra GPIO pins on these thigns

#

make them somewhat flexible

#

luckily the Nitehawk SB does have a couple lol

lean zealot Dec 6, 2024, 10:57 PM

#

The RP2040 should have enough to break out, but yeah

frank forge Dec 6, 2024, 10:57 PM

#

kinda silly

dense sequoia Dec 6, 2024, 10:57 PM

#

my other prinnter has niitehawk

frank forge Dec 6, 2024, 10:57 PM

#

I thought about getting the mellow fly cause it was cheap, glad I didn't lol

lean zealot Dec 6, 2024, 10:57 PM

#

Nothing wrong with it

dense sequoia Dec 6, 2024, 10:57 PM

#

its on my 1st voron

#

mellow fly

frank forge Dec 6, 2024, 10:58 PM

#

well it just would of been a headache for some the sensors

lean zealot Dec 6, 2024, 10:58 PM

#

I'll be moving my stuff to it when I go to CAN

#

How so?

frank forge Dec 6, 2024, 10:58 PM

#

well eventually we'll be able to use both sensors

#

I assume

#

idk I guess it doesn't really matter

lean zealot Dec 6, 2024, 10:58 PM

#

Oh, because you relocated X to your toolhead... that's right

frank forge Dec 6, 2024, 10:58 PM

#

I like their faceplate board though

lean zealot Dec 6, 2024, 10:59 PM

#

It's 1 pin short of being able to do all of that, which it's got a pad that might be able to be stolen for it

dense sequoia Dec 6, 2024, 10:59 PM

#

printing

frank forge Dec 6, 2024, 10:59 PM

#

nah that has nothing to do with it, I can connect all my sensors lol

#

oh ok

#

I was looking to see if there was something you could tap a pin from but didn't see much

lean zealot Dec 6, 2024, 11:00 PM

#

Fan 2 is unused in most cases on this, however idk if you can tap it for IO

#

#

GPIO15 in this case

frank forge Dec 6, 2024, 11:00 PM

#

ohhh ok

#

I didn't even notice it had 2 fans

dense sequoia Dec 6, 2024, 11:00 PM

#

yea i have a fan connected 3007

frank forge Dec 6, 2024, 11:00 PM

#

wonder if you could use the PWM pins

lean zealot Dec 6, 2024, 11:01 PM

#

It's got a face plate side that breaks it out like the NH stuff

frank forge Dec 6, 2024, 11:01 PM

#

I like the extra through hole connections for 5V and stuff on the mellow faceplate board

lean zealot Dec 6, 2024, 11:01 PM

#

Mike, can you send a pic of your toolhead wiring right now?

frank forge Dec 6, 2024, 11:02 PM

#

I would assume you could set the pin for a sensor to one of the PWM pins and use that

#

but yeah fan 2 would be usable too

dense sequoia Dec 6, 2024, 11:02 PM

#

rn_image_picker_lib_temp_bdd1cb26-45bd-4bce-957e-cca73d0e63b8.jpg

#

Old pic without Fan connected

lean zealot Dec 6, 2024, 11:03 PM

#

Oh

#

That's why I wanted a fresh one lol

dense sequoia Dec 6, 2024, 11:04 PM

#

Same wiring just with fan attached to the fan pads

#

Fan wires too short to open since i broke them a few times

lean zealot Dec 6, 2024, 11:04 PM

#

Okay, where are you connecting your current toolhead sensor?

dense sequoia Dec 6, 2024, 11:05 PM

#

GpIO27

lean zealot Dec 6, 2024, 11:05 PM

#

Sorry, not your thermistor, your filament sensor

dense sequoia Dec 6, 2024, 11:06 PM

#

Gpio29

#

Tap on gpio28

lean zealot Dec 6, 2024, 11:07 PM

#

#

Okay, so this little black wire is your filament sensor

dense sequoia Dec 6, 2024, 11:07 PM

#

Yes

#

Yes was pre wired before adding fan

lean zealot Dec 6, 2024, 11:08 PM

#

So that's where you'll have to take the one from inside the toolhead, you won't need Filatector any more

dense sequoia Dec 6, 2024, 11:08 PM

#

Correct

#

Ill move the single sensor inside

lean zealot Dec 6, 2024, 11:09 PM

#

Cool, as long as we're all on the same page, get it printed/assembled/and wired and we can come back then

dense sequoia Dec 6, 2024, 11:09 PM

#

👍

#

Printing the parts right now

lean zealot Dec 6, 2024, 11:09 PM

#

sweeet

#

So, probably a tomorrow project on all of it?

dense sequoia Dec 6, 2024, 11:12 PM

#

hopefully

#

i might try and get it done tonight

frank forge Dec 6, 2024, 11:13 PM

#

then just gotta put in all the stuff for the cutter into the config lol

dense sequoia Dec 6, 2024, 11:13 PM

#

yep

lean zealot Dec 6, 2024, 11:13 PM

#

That's 90% getting positions right

dense sequoia Dec 6, 2024, 11:13 PM

#

2 hrs to print

lean zealot Dec 6, 2024, 11:13 PM

#

Oh hell, we can work on it tonight if you have blades and stuff

dense sequoia Dec 6, 2024, 11:14 PM

#

I might have some blades but not sure

lean zealot Dec 6, 2024, 11:14 PM

#

Ah, I mean, we can always try to do tip forming as well as a temporary thing

dense sequoia Dec 7, 2024, 12:25 AM

#

#4 blades ?

hidden plank Dec 7, 2024, 12:26 AM

#

or the OLFA ones I have linked before

dense sequoia Dec 7, 2024, 12:26 AM

#

rn_image_picker_lib_temp_a6f49918-1130-451b-8dbe-f3ca5b6dfd30.jpg

hidden plank Dec 7, 2024, 12:26 AM

#

those work

#

needs to be cut/snapped to size - i used a jig off printables

#

search for filametrix jig

dense sequoia Dec 7, 2024, 12:26 AM

#

link ?

#

24,25,26mm ?

hidden plank Dec 7, 2024, 12:30 AM

#

i went with whatever is on the BOM - i think 26

lean zealot Dec 7, 2024, 12:30 AM

#

26 iirc

dense sequoia Dec 7, 2024, 12:31 AM

#

ok I found blades / jig

frank forge Dec 7, 2024, 1:29 AM

#

hidden plank needs to be cut/snapped to size - i used a jig off printables

I just used some pliers and held the part I needed to keep in the jaws and snapped off the back side lol

hidden plank Dec 7, 2024, 1:29 AM

#

same

vapid lantern Dec 7, 2024, 1:40 AM

#

dense sequoia ok I found blades / jig

https://www.printables.com/model/884349-erf-filametrix-4-hobby-knife-snapping-jig I used this

Printables.com

ERF Filametrix #4 hobby knife snapping jig by Borfon | Download fre...

Jig to make trimming the end off of a #4 hobby knife for your ERF filament cutter a breeze. | Download free 3D printable STL models

dense sequoia Dec 7, 2024, 1:47 AM

#

Nozzle clogged had to start over

dense sequoia Dec 7, 2024, 2:10 AM

#

dang x1c nozzlew clogged and cant get it unclogged

frank forge Dec 7, 2024, 2:44 AM

#

But I thought those things just work all the time

dense sequoia Dec 7, 2024, 2:45 AM

#

1st clog 3k hours

dense sequoia Dec 7, 2024, 4:07 AM

#

Hf nozzle junk just will not unclog

#

I have to order new nozxle...think I'll get a revo

vapid lantern Dec 7, 2024, 4:24 AM

#

dense sequoia I have to order new nozxle...think I'll get a revo

i got revo went from a rapido wont go back smh

dense sequoia Dec 7, 2024, 4:25 AM

#

for the x1c

lean zealot Dec 7, 2024, 4:31 AM

#

Have a friend that just put the Revo hot end on an x1c as well

#

it's nice, but nozzles are going to cost more

dense sequoia Dec 7, 2024, 9:36 AM

#

Have obsidian right now and it's clogged

#

I might look at the hako nozzle

frank forge Dec 7, 2024, 1:19 PM

#

Diamondback on sale on Amazon for SMRRF….. just sayin

#

30% off

dense sequoia Dec 7, 2024, 1:54 PM

#

nice whens that

#

and what diamond back

dense sequoia Dec 7, 2024, 2:00 PM

#

frank forge Diamondback on sale on Amazon for SMRRF….. just sayin

you have a link to one i can look at . probaly not on sale yet

frank forge Dec 7, 2024, 2:02 PM

#

Sec

#

Driving lol

#

The standard v6 one

dense sequoia Dec 7, 2024, 2:03 PM

#

dont htink that works on x1c

frank forge Dec 7, 2024, 2:03 PM

#

Crap looks like it ended yesterday

#

Ohhh right

#

My b forgot it was bamboozle

dense sequoia Dec 7, 2024, 2:04 PM

#

yea i have TC for both vorons

dense sequoia Dec 7, 2024, 4:16 PM

#

Threw the obsidian nozzle in the trash. I order the revo

cyan shuttle Dec 7, 2024, 4:21 PM

#

A torch wont clear it???

#

Ive yet to have a torch not clear a clog lol

dense sequoia Dec 7, 2024, 4:21 PM

#

nope I tried it after re-installing it just clunkys over and over

#

even took extruder apart ..ran filament up throught the extruder

cyan shuttle Dec 7, 2024, 4:22 PM

#

Riddle me this Mike.... Are you using a common filament on these machines that are getting the clog?

dense sequoia Dec 7, 2024, 4:23 PM

#

using inalnd galaxy black never had a issue until now

cyan shuttle Dec 7, 2024, 4:23 PM

#

If so, I would probably stop using that filament. I have a certain PLA that always causes me issues so I no longer use it.

dense sequoia Dec 7, 2024, 4:23 PM

#

this is abs

cyan shuttle Dec 7, 2024, 4:23 PM

#

Just an example. Its a PLA with a high glitter load and it leaves a lot behind in the nozzle. It prints fine but the next filament that goes in will have clogging issues.

dense sequoia Dec 7, 2024, 4:23 PM

#

abs glitter

#

brunning at 70

cyan shuttle Dec 7, 2024, 4:24 PM

#

Inland Galaxy Black should pretty much just be polymaker so its not too bad.

dense sequoia Dec 7, 2024, 4:24 PM

#

no i know

#

I loaded the filament and extruder just clicky and clicks

dense sequoia Dec 7, 2024, 6:23 PM

#

friend brought over a nozzle

frank forge Dec 7, 2024, 6:39 PM

#

if it was ABS soaking in acetone should do it too

#

might take a while though

dense sequoia Dec 7, 2024, 7:06 PM

#

yea

dense sequoia Dec 7, 2024, 8:17 PM

#

back in business

frank forge Dec 7, 2024, 8:22 PM

#

nice

dense sequoia Dec 8, 2024, 12:03 AM

#

printing parts so maybe tomorrow

#

been one of those days

dense sequoia Dec 8, 2024, 6:25 AM

#

one day I might get it finished

frank forge Dec 8, 2024, 7:04 AM

#

we all believe in you

dense sequoia Dec 8, 2024, 7:04 AM

#

finishing up the cw2 parts right now

frank forge Dec 8, 2024, 7:05 AM

#

nice

dense sequoia Dec 8, 2024, 7:06 AM

#

rn_image_picker_lib_temp_12a331cd-970a-4892-ae22-3f9575849a33.jpg

dense sequoia Dec 8, 2024, 7:34 AM

#

I think Im missing the front piece for the cutter

river jungle Dec 8, 2024, 7:38 AM

#

Looks like you have two back pieces

dense sequoia Dec 8, 2024, 7:56 AM

#

Yea i saw that

#

I thought i removed it but I guess I didn't

#

So printing front piece now

dense sequoia Dec 14, 2024, 8:42 PM

#

Unable to load module 'AFC_spool'

azure steppe Dec 14, 2024, 8:43 PM

#

rerun install script

dense sequoia Dec 14, 2024, 8:43 PM

#

ok

#

now TN 2 error

#

mcu 'turtleneck': Unable to connect

#

Nevermind i found the issue

dense sequoia Dec 14, 2024, 10:11 PM

#

how do I get the t0 - t03 macros back

white igloo Dec 14, 2024, 10:12 PM

#

They are built into the software now

dense sequoia Dec 14, 2024, 10:14 PM

#

I was using them to test the lanes

hidden plank Dec 14, 2024, 10:14 PM

#

you still can

dense sequoia Dec 14, 2024, 10:14 PM

#

how ?

hidden plank Dec 14, 2024, 10:14 PM

#

use the console?

#

T0

#

T1

#

etc

dense sequoia Dec 14, 2024, 10:14 PM

#

ok

#

cool ..finaly got toolhead cutter installed

#

Dang extruder heatrer failed again

dense sequoia Dec 14, 2024, 10:48 PM

#

recrimped again

#

keeps failing

#Disaster1234