build-help

[SOLVED] Endstop x still triggered after retract 94 messages

Mar 23, 2025, 12:48 PM Initial Setup

[Solved] Hmmm hot pockets 28 messages

Mar 23, 2025, 4:08 AM Tuning Build Issue Other

[Solved] Internal error on command:"PREP" 15 messages

Mar 23, 2025, 1:24 AM Initial Setup

[SOLVED] Question on printing parts (shrinkage) 23 messages

Mar 22, 2025, 4:20 PM Other

Flashing AFC board 35 messages

Mar 20, 2025, 6:41 PM Initial Setup

TNL BoxTurtle debugging 857 messages

Mar 20, 2025, 10:25 AM Build Issue

Stepper High TEMPs 18 messages

Mar 20, 2025, 12:20 AM Build Issue

[SOLVED] Lane 2 switches direction 5 messages

Mar 19, 2025, 10:00 PM Initial Setup

Spoolers not spooling 25 messages

Mar 19, 2025, 9:41 PM Build Issue

[Solved] LED Corners 7 messages

Mar 19, 2025, 8:41 PM Build Issue

GSTAT Error 72 messages

Mar 19, 2025, 7:22 PM Other

[SOLVED] I installed the mainsail update after that I get Internal error on command T0 107 messages

Mar 19, 2025, 2:45 PM Other

Nothing seems to work, but it says everything is fine 142 messages

Mar 19, 2025, 11:10 AM Initial Setup

(Solved) filament not cutting cleanly 50 messages

Mar 18, 2025, 4:10 PM Tuning Initial Setup Other

Startup issues occasionally 33 messages

Mar 18, 2025, 1:18 AM Other

[SOLVED] AFC Calibration command not working 4 messages

Mar 17, 2025, 6:58 PM Initial Setup

[Solved] TN1 not advancing filament when compressed as of V0.0.0-1298-gcde2a73c update 12 messages

Mar 17, 2025, 6:54 PM Other

LDO Box Turtle errors [Solved] 77 messages

Mar 17, 2025, 6:14 PM Build Issue Other

(solved)new board installed and get error lane4 tool cmd: T3 CHECK FILAMENT Prep: False - Load: True 5 messages

Mar 17, 2025, 4:01 PM Build Issue Initial Setup Other

[SOLVED] second can with BTT Pi + U2C 23 messages

Mar 17, 2025, 9:19 AM Initial Setup

mcu turtle shutdown (Solved) 128 messages

Mar 17, 2025, 8:06 AM Build Issue Other

IDEX config 58 messages

Mar 17, 2025, 7:16 AM Tuning Initial Setup Other

Won't extrude while printing. 17 messages

Mar 17, 2025, 5:10 AM Build Issue Initial Setup Other

Calibration reversed "UPDATED" 72 messages

Mar 16, 2025, 3:30 AM Tuning Initial Setup Other

When printing, the hot bed drops and the color changes does not rise 3 messages

Mar 16, 2025, 2:01 AM Initial Setup

Tool change doesn't run respoolers at first 10 messages

Mar 16, 2025, 12:21 AM Initial Setup

[Solved] flow sensor as pin_tool_start? 2 messages

Mar 15, 2025, 11:33 PM Initial Setup

[SOLVED] loading issues (solved 4 now) 13 messages

Mar 15, 2025, 9:03 PM Other

Infinity Spool 5 messages

Mar 15, 2025, 1:31 AM Tuning

[SOLVED] Lane 4 getting stuck at Hub 16 messages

Mar 14, 2025, 9:48 PM Build Issue

[SOLVED] Lane loading confusion 5 messages

Mar 14, 2025, 7:40 PM Initial Setup

Lane stopped switched after layer one 13 messages

Mar 14, 2025, 7:12 PM Build Issue Other

[Solved] FilamATrix not cutting properly 12 messages

Mar 14, 2025, 2:35 PM Tuning

Xol Metrix ptfe tube 10 messages

Mar 14, 2025, 11:41 AM Tuning Initial Setup

Problems assembling LDO BoxTurtle AFC kit 51 messages

Mar 14, 2025, 11:41 AM Build Issue

Stock E5+ advice 32 messages

Mar 14, 2025, 5:59 AM Other

buffer ram sensor 38 messages

Mar 14, 2025, 3:26 AM Other

2nd layer and above look horrible 7 messages

Mar 14, 2025, 12:56 AM Other

[Solved] Lanes 2 and 3 unloading too far 24 messages

Mar 14, 2025, 12:36 AM Tuning

[solved] Bad clogging again 10 messages

Mar 13, 2025, 9:27 PM Tuning Initial Setup

poop questions (solvedish) 9 messages

Mar 13, 2025, 4:51 PM Tuning

[SOLVED] Trouble with bowden length calibration 6 messages

Mar 13, 2025, 1:50 AM Initial Setup

had a weird one, didnt have time to record it ( solved ) 53 messages

Mar 12, 2025, 4:13 PM Other

Lanes 1 & 2 won't unload 10 messages

Mar 12, 2025, 6:35 AM Initial Setup Other

Cutter Macro 23 messages

Mar 11, 2025, 10:58 PM Initial Setup

Issues with AFC_CALIBRATION 32 messages

Mar 11, 2025, 3:01 AM Initial Setup

(Solved) Lane 1 and Lane 2 Respooler not Respooling 51 messages

Mar 11, 2025, 2:23 AM Initial Setup

no dfu mode 89 messages

Mar 10, 2025, 9:24 PM Initial Setup

[Solved] Macro order 8 messages

Mar 10, 2025, 5:51 PM Tuning

[SOLVED] Lane 2 Not Working 17 messages

Mar 10, 2025, 1:47 AM Tuning Build Issue