build-help

[solved] unable to set variable_conf_name_stepper_x: "" 10 messages

Apr 21, 2025, 8:05 PM Tuning

stn measurement. 11 messages

Apr 21, 2025, 3:29 PM Initial Setup

getting error mid serial print [solved] 28 messages

Apr 21, 2025, 3:02 AM Tuning Build Issue

[SOLVED] not sure what im missing but slots 2 and 3 wont trigger 208 messages

Apr 21, 2025, 2:27 AM Initial Setup

Prints peelings 82 messages

Apr 21, 2025, 1:08 AM Build Issue

seems as if im not able to connect to my afc after i finnished building it... 197 messages

Apr 20, 2025, 4:08 PM Initial Setup

[solved] White poop from hell 35 messages

Apr 20, 2025, 3:32 PM Tuning Initial Setup

[SOLVED] Boxturtle Setup Help (many things so far...) 87 messages

Apr 19, 2025, 11:27 PM Tuning Initial Setup

[SOLVED] Box turtle Enclosure 15 messages

Apr 19, 2025, 4:35 PM Other

Respooler turning the wrong way 3 messages

Apr 19, 2025, 10:20 AM Initial Setup

T0 is lane 2 now?? 4 messages

Apr 18, 2025, 10:44 PM Other

Multiple BT Canbus 7 messages

Apr 18, 2025, 10:41 PM Build Issue Initial Setup

under extruding? 3 messages

Apr 18, 2025, 7:23 PM Tuning

Filamatrix Not Consistently Cutting 33 messages

Apr 18, 2025, 1:00 AM Tuning Build Issue

Light Box - how to print? 9 messages

Apr 17, 2025, 1:11 PM Build Issue

Isiks Tech RGBW Neopixels 185 messages

Apr 17, 2025, 7:40 AM Tuning Build Issue Initial Setup

Dead spool motor in latest LDO kit 8 messages

Apr 16, 2025, 9:43 PM Build Issue Other

[Solved]Did my n20 just die? TSMC2209 was the issue 4 messages

Apr 16, 2025, 8:09 PM Build Issue

PLA Build 4 messages

Apr 16, 2025, 6:27 PM Build Issue

Feeder gear shaft lose 2 messages

Apr 16, 2025, 3:30 PM Build Issue

filament load at toolhead 20 messages

Apr 16, 2025, 4:13 AM Tuning Initial Setup

LDO Box Turtle Load issues. 9 messages

Apr 14, 2025, 11:21 PM Build Issue Other

Respooler not unwinding on lane eject. [CLOSED] 14 messages

Apr 14, 2025, 1:32 AM Build Issue Initial Setup

[SOLVED] Unspools To much 17 messages

Apr 13, 2025, 11:41 PM Tuning

[SOLVED] Start print not using T0 30 messages

Apr 13, 2025, 11:35 PM Tuning Initial Setup

Lane 4... again... solved 2 messages

Apr 13, 2025, 8:05 PM Build Issue

[SOLVED] dizzys adventures help thread 649 messages

Apr 13, 2025, 12:37 PM Tuning Initial Setup

Consistently fails to load 15 messages

Apr 13, 2025, 5:36 AM Other

Error Calibrating lanes [ SOLVED] Got it Working 48 messages

Apr 13, 2025, 12:13 AM Initial Setup

error heater bed 34 messages

Apr 12, 2025, 7:45 PM Initial Setup

TN-Pro keeps not trigering. 124 messages

Apr 12, 2025, 6:28 PM Other

[Solved] Oozing when loading filament 14 messages

Apr 12, 2025, 12:56 PM Tuning

MCU 'Turtle_1' shutdown: Timer too close 18 messages

Apr 11, 2025, 11:52 AM Other

(Solved) Unknown command:"HUBCUT" 16 messages

Apr 11, 2025, 2:36 AM Other

Cannot see AFC-Lite after flashing katapult 23 messages

Apr 11, 2025, 12:49 AM Build Issue

Invalid speed in 'G1 F-2147483648' (solved - slicer issue) 102 messages

Apr 10, 2025, 9:50 PM Initial Setup

Different "issues" with my build ["Solved"] 307 messages

Apr 10, 2025, 5:23 PM Build Issue

Issues encountered leading up to failure on first attempt at long running print 13 messages

Apr 9, 2025, 3:50 AM Tuning Build Issue Other

(Solved) Respoolers do not respool when unloading 45 messages

Apr 8, 2025, 9:58 PM Tuning Build Issue Other

(SOLVED) Hot end clogs after approx 10 or so filament changes 8 messages

Apr 8, 2025, 5:33 PM Tuning Initial Setup

Start_print/adaptive meshing help. 83 messages

Apr 8, 2025, 2:11 PM Other

filament residue 22 messages

Apr 8, 2025, 1:48 PM Initial Setup

[SOLVED] pin_tool_start value for TN-Pro 4 messages

Apr 8, 2025, 5:54 AM Initial Setup

tool load 4 messages

Apr 7, 2025, 9:34 PM Initial Setup

(solved) mcu turtle 1 shutdown issue 145 messages

Apr 7, 2025, 2:04 AM Other

[SOLVED] Respoolers over drive of feed 74 messages

Apr 7, 2025, 12:03 AM Tuning Other

[SOLVED] Extruder not releasing Filament on color change. 57 messages

Apr 6, 2025, 10:45 PM Build Issue

trouble with hub inputs on AFC for nightowl use with BTT MMB 117 messages

Apr 6, 2025, 8:56 PM Other

Tool End and Start not working? 44 messages

Apr 6, 2025, 6:25 PM Initial Setup

Multiple config files [solved] 9 messages

Apr 6, 2025, 4:11 PM Initial Setup Other