Can't connect Picam and Usbcam together | Mainsail | Page 1

visual iron Apr 12, 2023, 1:26 PM

#

Please help me to connect 2 camera which 1.raspicam and aukey lm1e together on mainsail. I used crownest so can't connect both of camera at the same time.

📎 log_file.txt

#

I try to fix this and DONE.
Afterthat i reboot the machine and found the problem

pallid glen Apr 12, 2023, 1:28 PM

#

So your problem is already solved?

visual iron Apr 12, 2023, 1:28 PM

#

#

after click FIRMWARE RESTART
The Raspi camera was gone just online the usb camera.

#

visual iron Apr 12, 2023, 1:31 PM

#

pallid glen So your problem is already solved?

not yet

pallid glen Apr 12, 2023, 1:31 PM

#

Your description was misleading sry for that.
What picam version are you using?

#

I found an issue not corresponding to the picam problem. Your AUKEY settings are wrong. They should like the following.

[cam AUKEY]
mode: mjpg
port: 8081
evice: /dev/v4l/by-id/usb-PC-LM1E_PC-LM1E_PC-LM1E-video-index0
resolution: 1920x1080
max_fps: 30
v4l2-ctl: focus_auto=0, focus_absolute=30

visual iron Apr 12, 2023, 1:37 PM

#

i will try

pallid glen Apr 12, 2023, 1:38 PM

#

What picam version are you using? v1, v2, v2.1, v3?

visual iron Apr 12, 2023, 1:44 PM

#

1.3

sterile zephyr Apr 12, 2023, 1:47 PM

#

visual iron Please help me to connect 2 camera which 1.raspicam and aukey lm1e together on m...

pls fix your tags -> #readme message

pallid glen Apr 12, 2023, 1:48 PM

#

visual iron 1.3

The dev of crowsnest said something like that.

For short I will drop the whole mimic in future. Raspicams v1 arent working at all in bullseye properly, they arent produced anymore so, screw it...
Can you run cat /etc/os-release and send the output?

visual iron Apr 12, 2023, 1:49 PM

#

pallid glen The dev of crowsnest said something like that. > For short I will drop the whole...

visual iron Apr 12, 2023, 1:49 PM

#

sterile zephyr pls fix your tags -> https://discord.com/channels/758059413700345988/10369339037...

Sorry i'm a newbie

#

Done but reboot fail

pallid glen Apr 12, 2023, 1:52 PM

#

Send your log file again please

#

What crowsnest version are you using?

visual iron Apr 12, 2023, 1:54 PM

#

just in install today

#

📎 message.txt

pallid glen Apr 12, 2023, 1:57 PM

#

I just remembered something that the buster support gets dropped with the next update but that shouldn't be of any problem for this atm

#

Please change your first section in the config accordingly

log_level: debug
delete_log: true
```send a log again after like 2min that crowsnest started fully

visual iron Apr 12, 2023, 2:01 PM

#

pallid glen Please change your first section in the config accordingly ``` log_level: debug ...

like this

pallid glen Apr 12, 2023, 2:03 PM

#

No change the [crowsnest] section

visual iron Apr 12, 2023, 2:08 PM

#

📎 message.txt

pallid glen Apr 12, 2023, 2:11 PM

#

visual iron Done but reboot fail

Did you do this correctly? Your /dev/video id is changing all the time for the raspicam

#

Change your port of the raspicam to 8082, something is blocking 8080 right now

visual iron Apr 12, 2023, 2:16 PM

#

pallid glen Apr 12, 2023, 2:16 PM

#

I need a log again

#

Can you send the output of sudo netstat -tulpn | grep LISTEN too?

visual iron Apr 12, 2023, 2:16 PM

#

pallid glen Apr 12, 2023, 2:17 PM

#

visual iron

log not config

visual iron Apr 12, 2023, 2:17 PM

#

📎 message.txt

pallid glen Apr 12, 2023, 2:18 PM

#

What are your webcam settings in Mainsail?

visual iron Apr 12, 2023, 2:19 PM

#

pallid glen Apr 12, 2023, 2:19 PM

#

Why do you have mjpg streamer running?

visual iron Apr 12, 2023, 2:19 PM

#

pallid glen Apr 12, 2023, 2:20 PM

#

Please change your snapshot url to /webcam2/?action=snapshot and /webcam3/?action=snapshot

#

You should disable mjpg_streamer, I think this was your previous solution for the cameras

visual iron Apr 12, 2023, 2:22 PM

#

pallid glen You should disable mjpg_streamer, I think this was your previous solution for th...

how to

pallid glen Apr 12, 2023, 2:23 PM

#

I don't know how you installed it. Maybe you are running a sudo crontab -e or maybe you installed it as a service

visual iron Apr 12, 2023, 2:24 PM

#

pallid glen Apr 12, 2023, 2:24 PM

#

1

#

but I don't think that you have used crontab for that then

#

ctrl+x to escape

visual iron Apr 12, 2023, 2:24 PM

#

pallid glen Apr 12, 2023, 2:25 PM

#

just exit with ctrl+x again

visual iron Apr 12, 2023, 2:25 PM

#

#

ok

pallid glen Apr 12, 2023, 2:26 PM

#

send output of ls ~

visual iron Apr 12, 2023, 2:26 PM

#

pallid glen Apr 12, 2023, 2:27 PM

#

Run cd ~/mjpg-streamer and make uninstall

visual iron Apr 12, 2023, 2:27 PM

#

pallid glen Apr 12, 2023, 2:27 PM

#

both single commands

visual iron Apr 12, 2023, 2:28 PM

#

sry

pallid glen Apr 12, 2023, 2:28 PM

#

cd ~/mjpg-streamer

#

make uninstall

visual iron Apr 12, 2023, 2:28 PM

#

pallid glen Apr 12, 2023, 2:28 PM

#

Maybe sudo make uninstall

visual iron Apr 12, 2023, 2:29 PM

#

pallid glen Apr 12, 2023, 2:29 PM

#

Try this then sudo rm /usr/local/bin/mjpg_streamer && sudo rm -r /usr/local/lib/mjpg-streamer && sudo rm -r /usr/local/share/mjpg-streamer

visual iron Apr 12, 2023, 2:31 PM

#

#

pallid glen Apr 12, 2023, 2:33 PM

#

find -name mjpg_streamer

visual iron Apr 12, 2023, 2:33 PM

#

pallid glen Apr 12, 2023, 2:34 PM

#

sudo find / -name mjpg_streamer

visual iron Apr 12, 2023, 2:34 PM

#

pallid glen Apr 12, 2023, 2:35 PM

#

visual iron

nothing else found?

#

or still running?

visual iron Apr 12, 2023, 2:36 PM

#

pallid glen Apr 12, 2023, 2:36 PM

#

Then just delete the mjpg_streamer folder with cd ~ && rm -r mjpg-streamer

#

maybe this will delete it

visual iron Apr 12, 2023, 2:36 PM

#

pallid glen Apr 12, 2023, 2:36 PM

#

pallid glen Please change your snapshot url to `/webcam2/?action=snapshot` and `/webcam3/?a...

Did you already changed like I said there?

pallid glen Apr 12, 2023, 2:37 PM

#

visual iron

cd ~ && sudo rm -r mjpg-streamer

visual iron Apr 12, 2023, 2:37 PM

#

pallid glen Did you already changed like I said there?

already changed

#

pallid glen Apr 12, 2023, 2:38 PM

#

cd ~

#

sudo rm -r mjpg-streamer

visual iron Apr 12, 2023, 2:39 PM

#

pallid glen Apr 12, 2023, 2:40 PM

#

just spam ctrl+c until you have an empty command line or a line with ^C or something like that

#

then run ```cd ~
sudo rm -r mjpg-streamer

visual iron Apr 12, 2023, 2:41 PM

#

pallid glen Apr 12, 2023, 2:41 PM

#

ls ~

visual iron Apr 12, 2023, 2:41 PM

#

pallid glen Apr 12, 2023, 2:42 PM

#

then sudo reboot

#

and if your cameras don't work send a crowsnest.log again

visual iron Apr 12, 2023, 2:43 PM

#

📎 message.txt

#

pallid glen Apr 12, 2023, 2:44 PM

#

So your raspicam still doesn't work or is this the aukey cam?

visual iron Apr 12, 2023, 2:45 PM

#

raspicam doesn't work

pallid glen Apr 12, 2023, 2:45 PM

#

nope it's the aukey cam

visual iron Apr 12, 2023, 2:45 PM

#

this swap automatically

pallid glen Apr 12, 2023, 2:46 PM

#

what does swap automatically?

visual iron Apr 12, 2023, 2:47 PM

#

webcam3 should be the Picam

pallid glen Apr 12, 2023, 2:47 PM

#

Yes, so your aukey cam isn't working anymore right now

visual iron Apr 12, 2023, 2:48 PM

#

visual iron

So the picture is AUKEY

pallid glen Apr 12, 2023, 2:48 PM

#

visual iron

On those pictures, you have NO SIGNAL on webcam2 and a picture on webcam3

#

webcam 3 is picam and webcam2 is aukey

visual iron Apr 12, 2023, 2:49 PM

#

If i unplug the USB AUKEY the raspi cam will show on the PI CAMERA

pallid glen Apr 12, 2023, 2:49 PM

#

visual iron

I'm really confused right now. Is this what is happening right now or something else?

#

Your pictures and log are telling me that your aukey cam isn't working

visual iron Apr 12, 2023, 2:52 PM

#

8081 is /webcam2 is PIcamera was installed at the lower corner
8082 is /webcam3 is AUKEY was installed at the top Front

pallid glen Apr 12, 2023, 2:54 PM

#

[cam raspicam]
mode: mjpg
port: 8082
device: /dev/video2
resolution: 1920x1080
max_fps: 15

[cam AUKEY]
mode: mjpg
port: 8081
device: /dev/v4l/by-id/usb-PC-LM1E_PC-LM1E_PC-LM1E-video-index0
resolution: 1920x1080
max_fps: 30

These are the settings from the last log you sent. If you changed something, send a new log please

visual iron Apr 12, 2023, 2:56 PM

#

pallid glen ``` [cam raspicam] mode: mjpg port: 8082 device: /dev/video2 resolution: 1920x10...

this current config

pallid glen Apr 12, 2023, 2:57 PM

#

visual iron 8081 is /webcam2 is PIcamera was installed at the lower corner 8082 is /webcam3...

And what's this then? I'm really confused right now

visual iron Apr 12, 2023, 2:57 PM

#

#

ok i unplug and plug agian

#

the name of camera is ok

pallid glen Apr 12, 2023, 2:58 PM

#

I think there is something really going wrong on your setup.

visual iron Apr 12, 2023, 2:58 PM

#

but Pucam not working

#

pallid glen Apr 12, 2023, 2:58 PM

#

Can you send a log again please?

#

Last log looked good for me

visual iron Apr 12, 2023, 2:59 PM

#

📎 message.txt

pallid glen Apr 12, 2023, 2:59 PM

#

Your raspicam is on the wrong device again Detected 'Raspicam' Device -> /dev/video0

#

That's why the picam showed the wrong one. You rebooted in between

visual iron Apr 12, 2023, 3:01 PM

#

My previous problem was
Once everything is set Then I reboot the machine. the pi was gone

pallid glen Apr 12, 2023, 3:01 PM

#

Ok, now I get the problem.

#

This "fix" didn't work for you

visual iron Apr 12, 2023, 3:01 PM

#

and the AUKEY switch to pi cam

visual iron Apr 12, 2023, 3:02 PM

#

pallid glen This "fix" didn't work for you

is work

#

but when reboot

pallid glen Apr 12, 2023, 3:02 PM

#

It didn't

#

This fix should be permanent after one time it worked

#

So please retry it. Make sure that your device is set to /dev/video0 in your crowsnest.conf. Then unplug the usb cam. Reboot your device and then wait until you see the raspicam stream. Then replug your usb cam, restart crowsnest once to see if both cameras show up

#

If that done reboot a few times to see if it's working or not

visual iron Apr 12, 2023, 3:05 PM

#

#

this one i change to /dev/video0

#

all fine

pallid glen Apr 12, 2023, 3:05 PM

#

Unplug the cam now

#

the usb one

visual iron Apr 12, 2023, 3:06 PM

#

pallid glen Apr 12, 2023, 3:06 PM

#

Now reboot and don't plugin the usb cam again

visual iron Apr 12, 2023, 3:07 PM

#

ok

pallid glen Apr 12, 2023, 3:07 PM

#

visual iron

You see this again right?

visual iron Apr 12, 2023, 3:08 PM

#

pallid glen Apr 12, 2023, 3:09 PM

#

Then plugin the usb cam again and open your crowsnest.conf and hit save & restart at the top right

visual iron Apr 12, 2023, 3:09 PM

#

pallid glen Then plugin the usb cam again and open your crowsnest.conf and hit `save & resta...

not FIRMWARE RESTART

#

right

pallid glen Apr 12, 2023, 3:09 PM

#

No

#

in the crowsnest.conf editor top right

#

don't click firmware restart

visual iron Apr 12, 2023, 3:10 PM

#

pallid glen Apr 12, 2023, 3:10 PM

#

yes top right the blue save & restart

visual iron Apr 12, 2023, 3:10 PM

#

plugin USB frist right?

pallid glen Apr 12, 2023, 3:10 PM

#

yes

#

then wait until you see both cams on dashboard again

visual iron Apr 12, 2023, 3:12 PM

#

#

#

ok

pallid glen Apr 12, 2023, 3:12 PM

#

Now run sudo reboot on your terminal

visual iron Apr 12, 2023, 3:13 PM

#

pallid glen Apr 12, 2023, 3:14 PM

#

Now see if your cams are still working after a few reboots

visual iron Apr 12, 2023, 3:15 PM

#

#

now the camera swap

pallid glen Apr 12, 2023, 3:15 PM

#

ok rip

#

I will get you someone here that maybe i willing to help or maybe not as he dropped the support for v1

visual iron Apr 12, 2023, 3:16 PM

#

🥺

#

Thank for your time

#

I've been trying to fix this problem for 6 hours now.

pallid glen Apr 12, 2023, 3:20 PM

#

I got another idea first

#

~~Backup your config and then reinstall crowsnest~~

#

wait

#

Run sudo echo "bcm2835-v4l2" >> /etc/modules

#

cp ~/crowsnest/resources/bcm2835-v4l2.conf /etc/modprobe.d/

#

this should apply the fix manually

#

If that doesn't work I will get the expert for you, he doesn't have that much time and need to focus on other thing so that's why I hesitate to ping ihm

pallid glen Apr 12, 2023, 3:23 PM

#

visual iron

Then you have to follow the steps from here on again and maybe that will help

visual iron Apr 12, 2023, 3:32 PM

#

Ok I will

#

Are you still there ?

pallid glen Apr 12, 2023, 3:38 PM

#

Yes

visual iron Apr 12, 2023, 3:40 PM

#

pallid glen Run `sudo echo "bcm2835-v4l2" >> /etc/modules`

This command don't need to backup first?

pallid glen Apr 12, 2023, 3:40 PM

#

You don't need to backup for that

visual iron Apr 12, 2023, 3:41 PM

#

pallid glen Apr 12, 2023, 3:42 PM

#

Maybe this will work: sudo (echo "bcm2835-v4l2" >> /etc/modules)

#

Not sure about the syntax right now

visual iron Apr 12, 2023, 3:43 PM

#

pallid glen Apr 12, 2023, 3:44 PM

#

sudo nano /etc/modules

#

Navigate with your arrow keys to the bottom of the file and paste in bcm2835-v4l2

visual iron Apr 12, 2023, 3:45 PM

#

pallid glen Apr 12, 2023, 3:45 PM

#

Press ctrl+s and then ctrl+x

#

and run cat /etc/modules

visual iron Apr 12, 2023, 3:46 PM

#

pallid glen Apr 12, 2023, 3:47 PM

#

sudo cp ~/crowsnest/resources/bcm2835-v4l2.conf /etc/modprobe.d/

visual iron Apr 12, 2023, 3:48 PM

#

#

no respond

pallid glen Apr 12, 2023, 3:48 PM

#

That's expected

pallid glen Apr 12, 2023, 3:49 PM

#

visual iron

Now follow these steps again

visual iron Apr 12, 2023, 3:49 PM

#

yup

visual iron Apr 12, 2023, 3:52 PM

#

pallid glen Then plugin the usb cam again and open your crowsnest.conf and hit `save & resta...

again with this step ?

pallid glen Apr 12, 2023, 3:52 PM

#

Yes

visual iron Apr 12, 2023, 3:59 PM

#

pallid glen Apr 12, 2023, 3:59 PM

#

Still working after multiple reboots?

visual iron Apr 12, 2023, 4:00 PM

#

The camera doesn't switch anymore.

#

reboot again

#

2 time reboot OK

#

^^

#

but why why the MCU error

pallid glen Apr 12, 2023, 4:02 PM

#

Your printer board isn't connected Ig, or maybe no configured correctly

#

But please open another post for that to keep some order in the forum

fast tide Apr 12, 2023, 4:04 PM

#

And please try not to be Captain Capslock again 😉 Cherio mate

visual iron Apr 12, 2023, 4:06 PM

#

23.03 PM in my country After this, I will be able to sleep soundly.

fast tide Apr 12, 2023, 4:06 PM

#

Then have a good night sir mainsail_heart

visual iron Apr 12, 2023, 4:07 PM

#

fast tide And please try not to be Captain Capslock again 😉 Cherio mate

try to find capslock

pallid glen Apr 12, 2023, 4:10 PM

#

visual iron try to find capslock

It should be 2 keys over your control key. He just meant that you shouldn't write the whole title in caps/big letters

visual iron Apr 12, 2023, 4:14 PM

#

ok

#Can't connect Picam and Usbcam together