klipper error | Mainsail | Page 1

rancid cloud Apr 11, 2023, 7:35 AM

#

I get this error evry time im done with a print how can i fix it

#

And cpu overloed i only have klipper add overheid also not its on a fan

grand latch Apr 11, 2023, 4:04 PM

#

Are you using timelapse, and do you have autorender at the end of print?

#

Like the error message states, this is most likely caused by something CPU intensive. It's impossible to tell anything without logs. Make sure to roll them over and then reproduce the error.

rancid cloud Apr 11, 2023, 7:10 PM

#

📎 klippy.log

#

📎 moonraker.log

rancid cloud Apr 11, 2023, 7:10 PM

#

grand latch Are you using timelapse, and do you have autorender at the end of print?

What are thouse

high musk Apr 11, 2023, 7:25 PM

#

What Pi are you using? Seems like pi1 or zero maybe?

rancid cloud Apr 11, 2023, 7:30 PM

#

i found the problem

#

high musk Apr 11, 2023, 7:38 PM

#

rancid cloud i found the problem

Just use Hard recovery or send the output of git status inside your ~/moonraker folder to further analyse the problem that mightr have occured

rancid cloud Apr 11, 2023, 7:39 PM

#

high musk Just use Hard recovery or send the output of `git status` inside your `~/moonrak...

i did hard recovery

#

you tink its fix because i need to print a long prunt

#

print

high musk Apr 11, 2023, 7:39 PM

#

I don't know

rancid cloud Apr 11, 2023, 7:39 PM

#

i hope

high musk Apr 11, 2023, 7:39 PM

#

I don't think so

rancid cloud Apr 11, 2023, 7:39 PM

#

ow

high musk Apr 11, 2023, 7:40 PM

#

I get this error evry time im done with a print how can i fix it
So you get the error midprint and not only at the end?

rancid cloud Apr 11, 2023, 7:40 PM

#

high musk > I get this error evry time im done with a print how can i fix it So you get th...

midprint also

high musk Apr 11, 2023, 7:41 PM

#

Are you interacting with mainsail during the print or are you running some webcams or klipperscreen with it?

#

Or are you using a telegram or discord bot?

rancid cloud Apr 11, 2023, 7:41 PM

#

umm im had a webcam but not anymore

rancid cloud Apr 11, 2023, 7:42 PM

#

high musk Or are you using a telegram or discord bot?

im using home assistant moonrakker to get a notify when print is done

#

maybe i need a heat sink

#

nervermind its under a fan

#

ohh i see cpu is getting high spikes 100%

#

high musk Apr 11, 2023, 7:45 PM

#

I'm not sure if a fan is enough for short spikes

high musk Apr 11, 2023, 7:45 PM

#

rancid cloud

temps?

#

Are the temps spiking with it or only the cpu usage?

rancid cloud Apr 11, 2023, 7:46 PM

#

only the cpu

high musk Apr 11, 2023, 7:46 PM

#

I want to see the temp under load

#

not just 1.5%

#

If the temp at 100% is like 80°, you really need a heatsink

rancid cloud Apr 11, 2023, 7:47 PM

#

how can i get it too 100%

#

starting a print ?

high musk Apr 11, 2023, 7:47 PM

#

rancid cloud

I don't know how you did it ther

rancid cloud Apr 11, 2023, 7:47 PM

#

ohh i meant 100% if cpu useig

high musk Apr 11, 2023, 7:47 PM

#

Maybe it was your homeassistant thing, that spiked it

rancid cloud Apr 11, 2023, 7:48 PM

#

or it just was the moonraker

high musk Apr 11, 2023, 7:48 PM

#

rancid cloud or it just was the moonraker

Moonraker shouldn't spike that hard except if it's searching for updates

rancid cloud Apr 11, 2023, 7:49 PM

#

i had a bad setup

high musk Apr 11, 2023, 7:49 PM

#

rancid cloud ohh i meant 100% if cpu useig

I mean 100% cpu usage too. I want to see the temps at 100% cpu usage

rancid cloud Apr 11, 2023, 7:49 PM

#

then it is 25

high musk Apr 11, 2023, 7:50 PM

#

Ok it's not the temp of the pi then

rancid cloud Apr 11, 2023, 7:51 PM

#

let me measure my 5v power supply with volt meter

#

if its stays the same voltage and w

high musk Apr 11, 2023, 7:52 PM

#

Can you send the output of ls ~ and maybe look at htop for a while and try to capture the process that spikes your cpu usage

rancid cloud Apr 11, 2023, 7:53 PM

#

high musk Can you send the output of `ls ~` and maybe look at `htop` for a while and try t...

i see a lot dont know where to look

high musk Apr 11, 2023, 7:55 PM

#

You have to look at the top line marked blue in your screenshot. If something goes over like 50% cpu usage, try to memorize the command line at the end of the marked line

#

You screenshot looks like cut off as the cpu% doesn't add up to 80%

#

or maybe you scrolled down

rancid cloud Apr 11, 2023, 7:56 PM

#

like this bar

high musk Apr 11, 2023, 7:56 PM

#

Yes

#

Please run systemctl disable crowsnest, you don't need crowsnest enabled anymore if you don't run a webcam

rancid cloud Apr 11, 2023, 7:57 PM

#

can i enebel it back when i connect cam ?

high musk Apr 11, 2023, 7:58 PM

#

With systemctl enable crowsnest you can enable it again

rancid cloud Apr 11, 2023, 7:58 PM

#

oke great

high musk Apr 11, 2023, 7:58 PM

#

But atm it doesn't make sense to add a cam as your pi cpu already overloads

rancid cloud Apr 11, 2023, 7:59 PM

#

its not normal that is keeps begin 100% right

high musk Apr 11, 2023, 8:02 PM

#

That's why I want you to find the process that is spiking your cpu

rancid cloud Apr 11, 2023, 8:03 PM

#

now its on 100% when this comes op and something with moonrakker

#

if i need to make a screen shot when its above 50% i got like 10000 screens

#

wait i need to shower

#

brb

high musk Apr 11, 2023, 8:08 PM

#

100% is good too

#

Just need the processes above 50%

#

When you are back please send your webcam settings in Mainsail

#

And send your printer.cfg and moonraker.conf

#

Did you disable crowsnest already?

#

Atm something seems to call ffmpeg sometimes. This spikes your CPU. My guess would be something with crowsnest or moonraker-timelapse

rancid cloud Apr 11, 2023, 8:12 PM

#

📎 crowsnest.conf 📎 moonraker.conf 📎 printer.cfg

rancid cloud Apr 11, 2023, 8:13 PM

#

high musk Did you disable crowsnest already?

i think so

high musk Apr 11, 2023, 8:15 PM

#

As I can't find anything on disabling timelapse, best would be to uninstall timelapse

#

Run cd ~/moonraker-timelapse && make uninstall

#

After that keep an eye on htop again to see if it still appears

grand latch Apr 11, 2023, 8:32 PM

#

Just my two cents, you need more processing power than 700 MHz and 512mb ram. No fans or anything will give your sbc more power. Best would be to disable as many features as possible until you can upgrade the hardware. It will only get worse as more features are introduced as they are all depending on your host machine cpu

high musk Apr 11, 2023, 8:40 PM

#

A pi zero 2 should be enough, even listed under the recommended devices

rancid cloud Apr 11, 2023, 8:58 PM

#

high musk A pi zero 2 should be enough, even listed under the recommended devices

yeah thats why i got it

#

i can upgrade to a pi 3

rancid cloud Apr 11, 2023, 8:59 PM

#

high musk Run `cd ~/moonraker-timelapse && make uninstall`

i uninstalled it

high musk Apr 11, 2023, 8:59 PM

#

That would maybe solve your problem but as it should run on a pi zero 2 we will try to fix that first

#

Then keep an eye on htop again to see if it still appears to spike

rancid cloud Apr 11, 2023, 9:01 PM

#

still getting this

high musk Apr 11, 2023, 9:02 PM

#

Can you send your mainsail webcam settings? The one you set in the cog wheel in the top right corner?

high musk Apr 11, 2023, 9:03 PM

#

rancid cloud still getting this

So it's still ffmpeg?

rancid cloud Apr 11, 2023, 9:04 PM

#

high musk So it's still ffmpeg?

yea

high musk Apr 11, 2023, 9:04 PM

#

Are there other processes taking sometimes more than 50% cpu?

rancid cloud Apr 11, 2023, 9:05 PM

#

now i got normal cpu stats

#

#

dont see ffmpeg

high musk Apr 11, 2023, 9:06 PM

#

Did you reboot after uninstalling timelapse?

rancid cloud Apr 11, 2023, 9:06 PM

#

nope

#

i will do know

#

do you have a cmd for that

#

F i shut it down now i need to walk to the hall in the gardian

#

i will look in it tomorow

high musk Apr 11, 2023, 9:13 PM

#

For reboot, just use sudo reboot

rancid cloud Apr 11, 2023, 9:41 PM

#

Yea i dit shutdown

#

I didentncopy it

rancid cloud Apr 12, 2023, 10:13 AM

#

this is the only command that get the cpu to 100% i think

high musk Apr 12, 2023, 10:15 AM

#

Ok that's bad as it could crash your print then maybe.

#

You could try a few smaller prints to see but I can't promise that it will work on longer prints without any problems

rancid cloud Apr 12, 2023, 10:42 AM

#

oke doeing a case for the pi now

#

on 3% load normal it whent getting some spiks but i dont see any

#

so its a good thing i hoop

high musk Apr 12, 2023, 10:48 AM

#

It should still spike but this time it's moonraker and not ffmpeg and that could already have solved your problem

rancid cloud Apr 12, 2023, 1:02 PM

#

yeah its runing from 12:40pm and still no spikes

#klipper error