#häufiger Fehler: max_extrude_cross_section

4 messages · Page 1 of 1 (latest)

stable kayak
#

Hallo am Sonntag,

ich bin bei meinem Voron jetzt nach 2 Wochen Zusammenbau soweit, dass er KlickyNG einwandfrei nutzt, damit eine Autocalibration z macht (nach homing und QGL) und der Abstand der nozzle zum Bett damit immer (meistens) einwandfrei ermittelt wird. Aber: nach dem Kalibrieren kommt bei Druckstart über Superslicer oft der Fehler: "Move exceeds maximum extrusion (0.817mm^2 vs 0.640mm^2)
See the max_extrude_cross_section" .

Woran muss ich da schrauben?
Bei Klipper (kann ich mir nicht vorstellen) oder bei Superslicer?

Habe in der printer.cfg testeshalber den Eintrag (der nicht vorhanden war) in der printer.cfg unter Extruder max_extrude_cross_section auf 0,9 hoch gesetzt.
Danach lief er einmal einwandfrei durch.
Danach aber wieder derselbe Fehler und der Druck stoppt.
Habe dann meine selbst erstellte purgeline auskommentiert (habe vielleicht unpassende Werte eingetragen), aber es folgt nach wenigen Millimetern Skirt:
Move exceeds maximum extrusion (12.995mm^2 vs 0.900mm^2)
See the 'max_extrude_cross_section' config option for details
12,995 ist ja nun wirklich viel zu hoch, um das durch einen neuen Eintrag höher zu setzen.

Der Fehler kann doch jetzt nur noch vom Superslicer kommen. Ich hatte im Superslicer schon alle Werte auf Standard zurückgesetzt.

Ich brauche jetzt dringend mal Input von Euch. Hat jemand eine Idee, woran ich mich begeben sollt.

Noch einen schönen Sonntag Abend.

summer trail
#

Hi, the language on that server is English. A good source if it must be German would be the German channel on the Voron discord.
I would check if the expected E mode M82|M83 (reletive/absolute) from the slicer fits the real printer one. the description of the error sounds like an issue in that direction.

spice vortex
#

or the "chaosdrucker" discord server...

stable kayak
#

Sorry, here in English:
"Hello on Sunday,
I have assembled my Voron for 2 weeks now and it is working properly with KlickyNG, so it does an auto-calibration in Z (after homing and QGL) and the distance between the nozzle and bed is always (mostly) accurately determined. But: after calibrating, when starting to print via Superslicer, the error often comes up: "Move exceeds maximum extrusion (0.817mm^2 vs 0.640mm^2)
See the max_extrude_cross_section".
What do I need to adjust?
With Klipper (which I cannot imagine) or with Superslicer?

I tested the entry (which was not present) in the printer.cfg under Extruder max_extrude_cross_section and set it to 0.9.
Then it ran properly once.
Then the same error again and the printing stops.
Then I commented out my own purgeline (maybe I entered inappropriate values), but after a few millimeters of skirt:
Move exceeds maximum extrusion (12.995mm^2 vs 0.900mm^2)
See the 'max_extrude_cross_section' config option for details
12.995 is definitely too high to raise it again through a new entry.

The error can now only come from Superslicer. I have already reset all values to standard in Superslicer.

I urgently need some input from you. Does anyone have an idea what I should do.

Have a nice Sunday evening."