support-forum

Trying to add another camera 10 messages

Jul 16, 2023, 5:40 PM webcam

Prusa Like M18 (disable motors) 11 messages

Jul 16, 2023, 4:22 PM klipper

Moonraker warningUPDATE MANAGER 22 messages

Jul 14, 2023, 9:46 PM linux moonraker

RaspberryPi Camera Dark and Zoomed in 57 messages

Jul 14, 2023, 8:07 PM webcam

crowsnest clarification 62 messages

Jul 14, 2023, 5:48 PM webcam

Crowsnest Incomplete! 27 messages

Jul 14, 2023, 5:02 PM webcam

Unable to get Logitech Camera to show up in Mainsail 4 messages

Jul 14, 2023, 4:15 PM mainsail webcam

Printer disconnecting from internet mid print and wont reconnect till reboot. 6 messages

Jul 14, 2023, 4:13 PM moonraker mainsail

The printers tab shows the same video feed for both printers 25 messages

Jul 14, 2023, 11:55 AM mainsail webcam

Wlan not changable via wpa file 56 messages

Jul 13, 2023, 5:42 PM mainsail

first install help! 3 messages

Jul 13, 2023, 3:15 PM mainsailOS klipper mainsail

What can cause this high bandwidth use 27 messages

Jul 13, 2023, 9:25 AM mainsailOS klipper

Crowsnest webcam settings or options 18 messages

Jul 13, 2023, 7:58 AM webcam

webcam crownest install error 7 messages

Jul 13, 2023, 1:41 AM webcam

Klipper connection error - ZeroDivisionError: float division by zero when connecting to Tronxy X5SA 4 messages

Jul 13, 2023, 12:59 AM moonraker mainsail klipper

Changing Wifi Networks 8 messages

Jul 12, 2023, 9:31 PM mainsailOS klipper

Webcam always 'NO SIGNAL' 28 messages

Jul 12, 2023, 6:16 PM webcam

sintax issue 3 messages

Jul 12, 2023, 4:13 PM mainsail

Crowsnest 46 messages

Jul 12, 2023, 1:25 PM webcam

Start Print: move out of range 29 messages

Jul 12, 2023, 1:22 PM klipper

How can I change the behavior of the Calibrate button in the Heightmap tab? 3 messages

Jul 12, 2023, 1:07 PM mainsail

WebRTC worked fine for a month but now stopped working. Endlessly trying to connect 40 messages

Jul 12, 2023, 9:50 AM webcam

Can't connect to printers with Mainsail 3 messages

Jul 12, 2023, 9:37 AM moonraker mainsail

Problems after updates 42 messages

Jul 12, 2023, 5:44 AM webcam mainsail klipper

downloading.cfg issue 4 messages

Jul 12, 2023, 4:56 AM mainsail klipper

Question to howto get bluez started (bluetoothctl issue) 14 messages

Jul 11, 2023, 6:14 PM linux mainsailOS

Smoothing time 6 messages

Jul 11, 2023, 4:45 PM klipper

Display Host Battery Percentage in temperature tab by "hijacking" temperature_host or other sensor 9 messages

Jul 11, 2023, 12:38 PM mainsail klipper

No Stream: Raspberry Pi Camera Module 3 65 messages

Jul 11, 2023, 12:51 AM webcam

need to save and restart crownset.conf for loading webcam (logi c270) 86 messages

Jul 10, 2023, 9:25 PM webcam

Where does the webui pull this from? 18 messages

Jul 10, 2023, 7:55 PM klipper

Pi Cam module 3 no image 30 messages

Jul 10, 2023, 7:32 PM webcam

Error massage after Installation. {% set extrude is not valid in section 'gcode_macro resume' 15 messages

Jul 10, 2023, 7:14 PM klipper

Move exceeds maximum extrusion 15 messages

Jul 10, 2023, 5:55 PM klipper

crowsnest install fail 28 messages

Jul 10, 2023, 11:41 AM webcam

Send print name to txt file 5 messages

Jul 10, 2023, 11:38 AM klipper

Klipper Not Working,Printer Isn't Ready 29 messages

Jul 10, 2023, 7:31 AM mainsailOS klipper

Macro Buttons not Displaying in Dashboard 4 messages

Jul 10, 2023, 3:54 AM mainsail klipper

Recommendations for Filament Management on One Printer 4 messages

Jul 10, 2023, 3:11 AM mainsail

Basic camera triggering 5 messages

Jul 9, 2023, 8:16 PM timelapse webcam

Webcam issue after upgrade to latest build 7 messages

Jul 9, 2023, 2:41 PM webcam

supported=0 detected=0, libcamera interfaces=0 8 messages

Jul 9, 2023, 2:38 PM webcam

Error occured in file: init_stream.sh -> construct_streamer 26 messages

Jul 9, 2023, 1:32 PM webcam

input shaper 2 messages

Jul 9, 2023, 12:47 PM mainsail klipper

make: *** [Makefile:17: install] Error 1 24 messages

Jul 9, 2023, 8:13 AM webcam

Webcam on Le Potato issue 17 messages

Jul 8, 2023, 10:06 PM webcam

Webcame not recognised 4 messages

Jul 8, 2023, 8:53 PM mainsail webcam

uninstallting v4 after upgrading it 23 messages

Jul 8, 2023, 4:41 PM webcam

Timer too close 37 messages

Jul 8, 2023, 3:34 PM linux klipper

3 printers, 4 Pi's, 3 Moonraker instances, One Mainsail client + webcams 26 messages

Jul 8, 2023, 9:34 AM moonraker mainsail webcam