support-forum

Dashboard Filament Length - 25mm Default 6 messages

Jan 4, 2024, 3:32 AM mainsail

Mainsail Update Manager Repo is corrupt for a large number 8 messages

Jan 3, 2024, 7:15 PM moonraker

Edit individual history item? 11 messages

Jan 3, 2024, 7:14 PM moonraker

No buffer space available', MCU 'mcu' shutdown: Timer too close errors 75 messages

Jan 3, 2024, 6:36 PM klipper

extrude setting problem 49 messages

Jan 3, 2024, 5:43 PM mainsail

klipper unable to detect gpio pin 5 messages

Jan 3, 2024, 8:02 AM klipper

Webcam Image black at times 3 messages

Jan 3, 2024, 2:31 AM webcam

Variable Problems 13 messages

Jan 2, 2024, 9:49 PM klipper

klippy disconnetc after print 49 messages

Jan 2, 2024, 9:26 PM klipper

Homeassistant sensor Progress 2 messages

Jan 2, 2024, 8:45 PM moonraker mainsail

ustreamer to yuyv 7 messages

Jan 2, 2024, 8:07 PM webcam

heightmap bed too low 3 messages

Jan 2, 2024, 7:31 PM klipper

Is this bad, what should i do 15 messages

Jan 2, 2024, 5:29 PM klipper

Z stepper driver not working 119 messages

Jan 2, 2024, 12:34 PM mainsail klipper

mainsail.conf showing "UNKNOWN" 4 messages

Jan 2, 2024, 7:39 AM mainsail

verify heater 36 messages

Jan 1, 2024, 7:47 PM mainsail klipper

SV04 display 40 messages

Jan 1, 2024, 7:27 PM klipper

OV5648 LED control... how to? (solved) 6 messages

Jan 1, 2024, 5:56 PM mainsail webcam

Moonraker: Path does not exit 4 messages

Jan 1, 2024, 5:41 PM moonraker

SV04 with Sonic pad 167 messages

Jan 1, 2024, 12:48 AM klipper

Crowsnest install problem 36 messages

Jan 1, 2024, 12:40 AM webcam

ESP cam cannot be operated with Mainsail 62 messages

Dec 31, 2023, 10:34 PM mainsail

Sonic Pad Extruder Motor Not Working 2 messages

Dec 31, 2023, 6:40 PM klipper

Trouble configuring crowsnest, adding an Axis IP Camera 4 messages

Dec 31, 2023, 6:13 PM webcam

xxxx mcu not able to conect 82 messages

Dec 31, 2023, 9:18 AM klipper

creality 4.2.2 board but with the rct6 chip 5 messages

Dec 31, 2023, 2:59 AM klipper

how can I add auto bed mesh here 6 messages

Dec 31, 2023, 12:11 AM mainsail

Adding an extra stepper to klipper 79 messages

Dec 30, 2023, 7:34 PM klipper

Webcams in separate views 2 messages

Dec 30, 2023, 6:06 PM mainsail webcam

Dumb question 40 messages

Dec 30, 2023, 5:43 PM mainsail

Mainsail can’t connect to Moonraker 8 messages

Dec 30, 2023, 2:50 PM mainsail

Why does this warning appear even tough its correctly connected? 23 messages

Dec 30, 2023, 10:55 AM klipper

What software can i use to remove the Firmware.bin from my raspberry pi? (i do it on macos) 38 messages

Dec 30, 2023, 9:51 AM klipper

How best to cool down the extruder during pause and re-heat on resume? 90 messages

Dec 30, 2023, 2:20 AM mainsail klipper

How to accurately tune acceleration and printing speeds + Orca Slicer settings - Sovol SV06 Plus 29 messages

Dec 29, 2023, 10:23 PM klipper

How do I do it: While writing code 14 messages

Dec 29, 2023, 6:58 PM mainsail klipper

Macro GCode to heat bed IF bed is < X, and wait for X. 283 messages

Dec 29, 2023, 6:05 PM klipper

blank page 6 messages

Dec 29, 2023, 5:55 PM mainsail

Picam v3 issue 17 messages

Dec 29, 2023, 2:31 AM webcam

when i make a modification to moonraker mainsail doesn't work 2 messages

Dec 29, 2023, 12:03 AM moonraker mainsail klipper

Webcam panel missing on Dashboard 8 messages

Dec 28, 2023, 9:50 PM mainsail

Bedmesh 10 messages

Dec 28, 2023, 5:01 PM klipper

Skr pro, struggling to get Pi to talk to mainboard 33 messages

Dec 28, 2023, 2:40 PM mainsail klipper

Setting "auto_exposure" v4l2ctl flag in crowsnest.conf does not work, but does from terminal 3 messages

Dec 28, 2023, 3:51 AM webcam

Installed MainsailOS on pi4 - crowsnest fails to start 14 messages

Dec 28, 2023, 3:01 AM mainsailOS webcam

My printer randomly disconnects from the host 47 messages

Dec 28, 2023, 1:07 AM mainsail klipper mainsailOS

Headless RPi Wifi Connectivity Issue. 11 messages

Dec 27, 2023, 5:20 AM mainsailOS

mainsail not loading 95 messages

Dec 27, 2023, 3:15 AM moonraker mainsail

Internal error on command:"SDCARD_PRINT_FILE" 58 messages

Dec 26, 2023, 7:47 PM mainsail

Is it possible to see multiple spaces in the console? 12 messages

Dec 26, 2023, 12:40 AM linux mainsail klipper