Ender 5 Plus - Mercury 1 (Classic) with Stealth Burner and New Enclosure Project

[dawn vapor]

I have everything wired up. Raspi going to octo. Octo going to u2c and u2c going to can toolhead

[naive swan]

So everything is connected and proper?

[dawn vapor]

But my klipper interface is still giving me boot up errors

I think because not all my endstops are connected

Still have to solder my y

[naive swan]

The config for the screen is a pain in the ass

The skr2 isn’t well documented

Neither is the btt v1 screen (at least for klipper)

[dawn vapor]

My printer boots up

I also got the pwm fan to work with a 3 pin fan so the tach will stop printer if fan stops spinning

[mild hinge]

tach ?

[dawn vapor]

Tachometer

Looks like im going to have to get a 4 pin pwm fan for it to work pro

Properly*

@naive swan what does your output pin motor power command do on your config?

[naive swan]

no idea lol

[dawn vapor]

Hmm.

[naive swan]

its skr2 specific

[dawn vapor]

Ooooh

It kills your hot end pins when flashing

[naive swan]

motors wont turn on without it

[dawn vapor]

I member

[vocal terrace]

yea keep it in

[dawn vapor]

Im 2/3 of the way wiring. Printing burgos arms and hopefully get this up soon

Everything turns on. Klipper on mainsail is up and just have to clean wires and my fan on psu because it sounds like it has a toy in it

[dawn vapor]

Any other worthwhile configs to add?

[naive swan]

your going to need a new z tilt

[naive swan]

Hydra is done and implemented

works perfectly with the enclosure

still some new parts to add but i will put the cad up soon

[mild hinge]

Nice

[vocal terrace]

New octopus pro is installed canbus 2.54 JST-XH

[vocal terrace]

48V psu and fans on the way hehhe

[mild hinge]

Nice

[deep vine]

Okay, I can confrim, that the cnc tap has no play

[vocal terrace]

Yes but what's ur adxl results?

[deep vine]

I have not tested yet

[naive swan]

A little loud

[vocal terrace]

A little RATIO!!!

Also that's slow as shit

I'm disappointed

[naive swan]

Yeah 1st run

I’m not cranking it on the 1st run….you amateur…. Ratio that

[vocal terrace]

What about kombucha?

[deep vine]

looking good vengie, whats the results looking like?

[deep vine]

ohh nevermind i se you posted the results earlier

[naive swan]

Just printing the rear stepper mounts again

[vocal terrace]

and i'm posting the RESULTS OF THIS RATIO

[dawn vapor]

Incoming!

[naive swan]

Since last time I printed them my belts were stretched

[deep vine]

so the hydra system wasnt able to take out that taco effect, mabey over time it will have freedom to settle

[naive swan]

I think it won’t solve it, but at least it’s stable now

[deep vine]

nice! i ordered the same belts as you got, i will reprint the mounts with sunken stepper

[naive swan]

The belts are good

[deep vine]

good

[dawn vapor]

Thats with the beacon probe vengeful?

[naive swan]

Yes

[dawn vapor]

And your bed temp is stable?

[naive swan]

Yes no bounce on that

[vocal terrace]

see if when ur machine is heatsoaked if it helps too

[naive swan]

Looks like my zbanding is gone but I will post a comparison after these parts are done

[deep vine]

did you add wobblex?

[naive swan]

No

Just some old hams

[vocal terrace]

some already printed my files

#1100961592369217546

[deep vine]

have you tested them yet?

[vocal terrace]

i don't have anything with lead screws other than an ender 3 rn

my hydra need frame + bed

• alot more

[deep vine]

ohh

[vocal terrace]

should only need to add potentuially top mount for lead screws

[deep vine]

has anyone made a belted hydra yet?

[mild hinge]

@dawn vapor Like the plate

@dawn vapor where and who did that for you

[dawn vapor]

Skilled CNC, LLC
695 s ridge lane Appleton, WI 54914 US
(262) [email protected]://www.skilledcncwi.com

By far the most reasonable shop. Local places where quoting me 140

[mild hinge]

yea

[dawn vapor]

This shop is quality work and reasonable.

My plates for a 5+

[mild hinge]

nice

yea i have the ender 5 plus ..have no plates yet

like to enclose it

[dawn vapor]

Im doing the corrugated board for sides and back. Clear plexiglass for front doors and inside top plate/top hat

[mild hinge]

nice

whats sizes do I need

[dawn vapor]

Ill let you know in a min. Actually going to Michael’s right now to pick some up

[mild hinge]

awesome

[dawn vapor]

Its at least 500mm by 500mm

[mild hinge]

I have a michael 10 min from me

homedepot has 4mm sheets of it

white

I can spray paint it

[dawn vapor]

I think i priced the sheets there a bit high

The Michael’s is already black at 3 something each

[mild hinge]

36x72 2498

can you send me a link

Ill check the michaels close to me

20" x 30" x 0.16" (50.8cm x 76.2cm x 0.43cm) 4.99

[naive swan]

thats it

just get a 20% coupon and you are golden

[mild hinge]

Correct size ?

ill pick that up tomorrow

they have 7 in stock

30% off too

[naive swan]

nice

i use the 20x30 sheets

[mild hinge]

ok

Ill be picking up them tomorrow

[dawn vapor]

https://www.michaels.com/product/10567770

[mild hinge]

yep what Im picking up tomorrow

LP Beacon shipped today

[naive swan]

nice

[mild hinge]

printing a F1 race car

[naive swan]

!

like a model?

or the panels to a real one?

[mild hinge]

https://www.youtube.com/watch?v=2hL_LCXAZQk

[naive swan]

oh nice

[vocal terrace]

3d print this ratio

[mild hinge]

ratio ?

[mild hinge]

you said " 3d print this ratio"

[vocal terrace]

Take this second ratio

[mild hinge]

Yea i have a few pleco's

in a 120 gallon tank

[vocal terrace]

Ur lucky not on PC I'd send naruto and sasuke kissing

bruh its birdie wing day I forgor

Penis life time!!!

[mild hinge]

also have a 80 gallon saltwater TANK

[vocal terrace]

It says venus

[vocal terrace]

Cool I don't have any tanks. That's my work

THEY HAVE 1000 GALLONS+ OF SALTWATER

[naive swan]

i havent finished mine

[vocal terrace]

Also 30k+ of fish

Ans is small business lol

But I do know about fish prices.

[mild hinge]

saltwater alot of work

[vocal terrace]

Yee

I dont want a tank for that reason

Also saltwater is the cool stuff only way I would

[mild hinge]

its enjoyment

[vocal terrace]

I get enjoyment from my printers

And keyboards

[mild hinge]

yea

[naive swan]

One of those projects that I want to finish but I can’t take the extra work

[dawn vapor]

Just

[mild hinge]

lol

[vocal terrace]

https://youtu.be/UfEIharoOH0

@dawn vapor u watch?

Also I like that we just tlak in this build log

It's the cool channel

[dawn vapor]

I hate real life golf. But this is a show i can get behind.

[mild hinge]

https://www.youtube.com/watch?v=jPxlsi9OuSg

[vocal terrace]

I fricken love jr

It

I definitely wanna 3d print a ariel

[naive swan]

@mild hinge One day I will set up my office downstairs and the saltwater tank will be a great item for my office

[mild hinge]

@naive swan yep

[dawn vapor]

Put put miniature is cool

[vocal terrace]

Spend as much as printer hehheeh

Holy fuck fish are expensive

Whats ur fav so far?

I really really like Royal Gramma

[mild hinge]

i have more in fish equipemt then 3d printers by far

[naive swan]

Saltwater tank is more expensive

[vocal terrace]

Today I got to call a rival fish shop and get them to bs quote me 1/2 of fish cost

[naive swan]

Plus a lot of work

[vocal terrace]

25-30 CAD for a royal gramma that goes for 70 bucks at my work

[naive swan]

Water replacement and all the extras, live sand and live rock

[vocal terrace]

Also ordered a better enclosure for the e3v2

[naive swan]

Coral

[vocal terrace]

We have a 30mm diameter price for 500 bucks

Wanna vc anyone soon?

[dawn vapor]

You gotta go to the local distributor of the fish

[vocal terrace]

@mild hinge u got a mic/ headset?

[vocal terrace]

I literally work for a aquairum

[mild hinge]

yes why

nice

[vocal terrace]

Vc some time

[dawn vapor]

Theres one near me. They sell what big store sells for penis*

[mild hinge]

yea

soemtimes I do VC

[dawn vapor]

That one was for you burgo

[naive swan]

Oh lol

I didnt realize he worked at an adult store, I thought it was a fish shop

[vocal terrace]

bruh

listen to venus line

[mild hinge]

lots of fish there ...lol

[vocal terrace]

and tell me its not penis lfie

[mild hinge]

puffer ...lol\

[vocal terrace]

I have 1.5k in keyboad I just realised ):

thats a miniumum

gonna 3d print 1 soon

[dawn vapor]

I personally like the remoras

[vocal terrace]

https://www.livingaquarium.net/

thats the place I work at

just wanna let u know I just do website

[dawn vapor]

Uh oh.

[naive swan]

I just want coral

[vocal terrace]

needa finally set them with a good website

[dawn vapor]

Someones gona get some adult toys delivered there

[vocal terrace]

Yes idc

[dawn vapor]

3d printed ones. Keeps the shipping cost down

[vocal terrace]

my boss is into 3d printing too

[vocal terrace]

n o

molded

u can't fuck ur prints

[dawn vapor]

Little penis chess set

[vocal terrace]

unless acetone smoothen

[mild hinge]

ribbed devices ...oh no

[dawn vapor]

Saw someone print that on reddit

[vocal terrace]

it will get nasty

[mild hinge]

lol

[dawn vapor]

Was actually pretty cool lol

[vocal terrace]

@hot flint So u can agree u can't fuck prints?

[dawn vapor]

He neopixeld the board

[naive swan]

Tpu prints?

[vocal terrace]

I neewda do more neopixel stuff

I have 50

[dawn vapor]

Um you can literally screw anything if you put your mind to it

[mild hinge]

that reminds me i need to find a neopixel mount for ender 5 plus

[vocal terrace]

for where?

[naive swan]

50 tpu printed toys?

[vocal terrace]

@naive swan join vc if ur cool

[dawn vapor]

Im just using the voron variants

[vocal terrace]

I HAVe 50 neopixels

[naive swan]

That’s a lot of tpu

[mild hinge]

https://www.th3dstudio.com/product/ezneo220-rgb-printer-lighting-strip/

here is the neopixels I have

[vocal terrace]

my cart for mellow is 700 bucks lol

without new steppers

ok SIDE PACK time!

aluminium one

https://www.aliexpress.com/item/1005004121247823.html?spm=a2g0o.cart.0.0.297838da5qX9Me&mp=1

tempted to get 1 of these

[naive swan]

Reminds me I need to remake the max power for the type v

[vocal terrace]

but wait dfor super power 50mm shaft

[mild hinge]

nexopixels 220mm Length

[vocal terrace]

nah

[naive swan]

I might try them

[vocal terrace]

u should

they would be perfect

[naive swan]

Agree

[dawn vapor]

The last set i bought from th3d lasted a month in the 40c chamber

[vocal terrace]

I'm now waitinf for stuff to work to have the voron up aain

[mild hinge]

Mine still going

[vocal terrace]

needa remove the bad bed heater

also @naive swan will tell scott to eat shit

[dawn vapor]

Im going for that disco stick

[mild hinge]

I have the disco sticks on the voron

[vocal terrace]

AND I'm GOING FOR THAT RATIO!

burn where u not there when he questioned me saying bad heater

[dawn vapor]

And i need to figure out how to get my printer to play music

[vocal terrace]

pretty easy

u have GPIO pins remember

u can use those

[dawn vapor]

So it can play

[vocal terrace]

I've gotten stuff to play megolovania

ACTUALLY I'm ADDING THAT TO VORON

alot of screens have buzzers too fyi

[dawn vapor]

https://youtu.be/LJOTBSE_3Dw

[vocal terrace]

I want the gay version

and also to start making out

https://tenor.com/view/naruto-and-sasuke-sasunaru-anime-make-out-kissing-gif-17946686

[mild hinge]

gross

[vocal terrace]

woah

u homophobic?

[vocal terrace]

it's just a goodnight kiss

[mild hinge]

shit more then that

https://www.instructables.com/Make-Your-3D-Printer-Play-Music/

[vocal terrace]

CAN I GET A KISS

AND CAN U MAKE IT LAST FOREVER

cause idk when I'mma see yoiu again!

[dawn vapor]

Can i canbus an arduino mcu to a raspi

[vocal terrace]

yes.

but

ur dumb

u have GPIO

whats the SB2040 use?

a RP2040

[dawn vapor]

I have leds on toolhead. Ima have leds in electronics enclosure and i want leds in print area

[vocal terrace]

double density barf

[mild hinge]

I have barfs, 3 disco sticks and Leds underneath the printer and PI 4 ICE tower LED fan

[vocal terrace]

i want dragon burner cause double density barf just realized

or normal

https://github.com/CorvidBuilds/Mantis-Xol

it comes in this week

[mild hinge]

I have 2 Voron Dragon HF

[vocal terrace]

no

draonburner

[mild hinge]

what is dragon burner

[vocal terrace]

vo toolhead soon to be sb too

[mild hinge]

https://www.youtube.com/watch?v=ooU3U1dBz1Q

[vocal terrace]

yee

[mild hinge]

looks cool

[vocal terrace]

more powerful than SB

[mild hinge]

would have to design it for the sb2040/3do nozzle cam

https://www.printables.com/model/457167-dragon-burner-mgn12h-mount-with-and-without-klicky

[vocal terrace]

more files are coming kyle has it

[mild hinge]

kyle ?

ill wait until it has what I need

[naive swan]

Hopefully this time they come out without issues, my old belts were too inconsistent and the print drifted slightly to the side

[mild hinge]

guess klipper is dead

will not start

rebooted PI and klipper

time to start over I guess

No USB listed in lsusb so something is broken

Have to reflash hopefully mainboard not bad

[silent hamlet]

do they work with the non plus? could you share these so i can modify the lengh so does it fit to my pro

[mild hinge]

I have a junk printer ender 5 plus ...removing parts ..scraping it

just bought a brand new board and its junk only got 1 print out of it

if anybody wants or is looking for a project printer. Getting rid of it

before I scrap it

[naive swan]

everything is here - https://github.com/Vprince099/ZANDVE

@silent hamlet and yes it all works with a pro(if going hydra) but things like the skirt have to be redone

[silent hamlet]

i just want to have the parts on the Z and the rods because i have no hydra and i will close the electronicsbay

thank you very much vegeta

ahh @naive swan

😄

[vocal terrace]

Meiw

[mild hinge]

Just scrapped the ender 5 plus
Pulled the
The core xy off and the bed plate/dragon

In the trash.

I'll be focusing on finishing the voron

[deep vine]

dont do it mikey! ill help you fix it

[naive swan]

I feel this way about my V0 all the time

[mild hinge]

its done ...now voron belt came off and took cnc apart partial apart and washer fell out ...Im done with 3d printers.

anybody want to buy 2 project printers

if not Ill put for sale

local

[dawn vapor]

Y

[dawn vapor]

Y

[dawn vapor]

Im doing this with rheumatoid arthritis. I either have weak hands or my dexterity is shit and i cant properly hold tools. I feel your pain.

[dawn vapor]

@naive swan are you running any camera in chamber of your builds?

[naive swan]

No I use an external camera on a ring light stand

[vocal terrace]

lol me cause that frame

bruh he leacve?

[naive swan]

I think he quit on the ender because it was too many things going wrong

[dawn vapor]

Cable management

And going senseless homing

And ill be redoing all this in a few weeks for hydra lol

[naive swan]

looks very nice

i may switch back now that i have a virtual z endstop

precision on homing is not as important anymore since i dont use auto z or Klicky

[dawn vapor]

Frame feels pretty solid with the hydra extrusion in the back.

I was putting together the latches for the top hat. How does the unlock mechanism work?

[deep vine]

Don’t give up on it, we will guide you through it, just finish your Voron then come back to this. Honestly it will be fine.

Nothing is unfixable

Acctually boys!

Check this shnizzle

[vocal terrace]

its not even that good lol

30g

):

or that much more

[deep vine]

30grams is a a lot at this scale

[vocal terrace]

yes but going not tap is less weight heheeh

also CF pins is weight difference

[deep vine]

Them tiny pins saves weight too

[mild hinge]

Just picked up a ender 5 pro 75.00

[vocal terrace]

lol

gonna get rid of machiens....

buys machine....

the frame can have big effects.

[mild hinge]

Not for me

Picked up for a friend

[vocal terrace]

don't get rid of the others just let it sit for a while ngl.

[deep vine]

Into bad

[deep vine]

I agree with that ratio

[mild hinge]

Buddies issue not mine

[vocal terrace]

agree with dis DICK

[deep vine]

https://tenor.com/view/uzui-better-gif-24953549

[vocal terrace]

looks like shit

RAITO

[deep vine]

https://tenor.com/view/twitter-ratio-battle-sus-sussy-gif-21593804

[vocal terrace]

https://tenor.com/view/naruto-and-sasuke-sasunaru-anime-make-out-kissing-gif-17946686

[deep vine]

You got me there like

[mild hinge]

Not that again

[deep vine]

Is that your dreaming of lettuce foot

[vocal terrace]

no

I don't like foot lettuce...

[deep vine]

Lettuce teeth then

😉

[vocal terrace]

no kombucha

[mild hinge]

Voron up and running

[vocal terrace]

L + ratio

[deep vine]

Your self fal-ratio

[vocal terrace]

KOMBUCHA MOUTH ON DEEZ NUTS

[deep vine]

https://tenor.com/view/suck-david-suck-gif-19355553

[deep vine]

Send pics

[mild hinge]

Sko

[vocal terrace]

wtf are those XY joints

[mild hinge]

Cnc

[vocal terrace]

thats not a stock bed right

[deep vine]

Nice

[mild hinge]

Yes it is just no magnet

[vocal terrace]

ew.

get rid them cable chains

also get this

https://www.aliexpress.com/item/1005004121247823.html?spm=a2g0o.cart.0.0.779f38daQ5h1Wp&mp=1

[mild hinge]

That's cool

[deep vine]

Don’t listen to lettuce man, he make you spend money on random shit

[mild hinge]

Well yea

[deep vine]

Haha

[vocal terrace]

stfu

I spend money on stuff. Then I'm getitng rid of it now

[mild hinge]

I have voron backers on the way

[deep vine]

😂

[vocal terrace]

got rid of some motors hehehehe

[vocal terrace]

I got rid of my X

I'll see how my thermals are effected by it.

[deep vine]

https://tenor.com/view/ratio-didnt-ask-you-fell-off-cope-dont-know-what-youre-talking-about-gif-23606778

[vocal terrace]

ur mom

[deep vine]

https://tenor.com/view/cringe-eeee-gif-24636179

[vocal terrace]

her face looked different last night

[mild hinge]

Google eye's

[dawn vapor]

Wow jellybob came in with fists of fire.

Is this a ratio battle?

[vocal terrace]

No

[dawn vapor]

Ratio war?

Cringe match?

Are creality stepper motors the only ones with screwed up wiring?

[vocal terrace]

Middle flipped. Check LDO for how

[dawn vapor]

So A1 is A A2 is B?

[vocal terrace]

No AC

Those 1 pair

[dawn vapor]

So a+ and a- are a pair

[vocal terrace]

The diagram shows that 1 is a 3is C hence its middle wires flipped from crwality

[dawn vapor]

Ok so i have black- A green C Red B Blue D on motor. Going to Black A+ Green A- Red B+ Blue B-

[vocal terrace]

Ngl idc I'm making cookies rn

[vocal terrace]

@dawn vapor just sewnd it

motors bad u flip 2 middle wires

[dawn vapor]

I flipped them. A+ and A - are a pair correct. Tested for continuity and flipped middle wires to have each pair next to each other

[vocal terrace]

U won't dm motor just stepper buzz

[deep vine]

To confirm if you have a pair, you can touch the two wires together then turn the motor, if you feel resistance, that means they are a pair

[naive swan]

Or use a multi meter and check for continuitie

New v0.2 top hat is done

Mini SB is done as well

Still can’t print overhangs on my merc

[vocal terrace]

Dragon burner

[vocal terrace]

Better fans or the frame could be it

[naive swan]

No

I need to get this going

You don’t know what scope creep is do you?

[vocal terrace]

Scope creep?

[naive swan]

Yes watch a YouTube video or something

[vocal terrace]

Ah. Makes sense it explains why u have shit frame

[naive swan]

But I agree the fan must be under powered

[vocal terrace]

Get delta or sunon

Also looks like another issue

[naive swan]

It’s the part cooling

[vocal terrace]

Cause look at the other piece for back that's thicker

[naive swan]

It only happens in the back of the part

[vocal terrace]

What's the bed mesh look like?

[naive swan]

Where the part fan doesn’t hit

[vocal terrace]

It's it always the back?

[naive swan]

Yes

Always

[vocal terrace]

Like very end of the buildplate?

[naive swan]

No

Back of each individual part

Every time

[vocal terrace]

That's so weird

[naive swan]

It’s the fan

[vocal terrace]

It could be extruder too though.

[naive swan]

Not strong enough

[vocal terrace]

Yea

Go XOL2

Wait cpap

I forgor

[naive swan]

It only reaches front and sides

[vocal terrace]

Is it cause beacon?

Ur duch is less?

[naive swan]

Well for the time being all my overhand parts will print on the V0

[vocal terrace]

U planing on cncjng ur own vzbot stuff?

[naive swan]

Most of those parts are decorative anyway

I would cnc hexort parts if that’s the route I was going

[vocal terrace]

XOL2 and mobiys parts

[naive swan]

Nice

[vocal terrace]

My M4 is rekt by filament need move ith

[naive swan]

I might do a mini hydra merc

[vocal terrace]

Lol

Do saladfork

[naive swan]

Nope

[vocal terrace]

50mm linears

Or mgn7

Honestly vengeful I'd be so down to help

But do it belted for the fun

[naive swan]

It would be 1515 with a rear pack

[vocal terrace]

Why not 2020

[naive swan]

Like a micron

I like 1515

[vocal terrace]

Ew

[naive swan]

And the challenge

[vocal terrace]

I think imma do dual ender 3 bed motors

AWD/ K3 style

In a switchwire.

[vocal terrace]

I like salad

[naive swan]

Utoc or utc or figure out how to use the onboard can from the fly Gemini v3?

[vocal terrace]

Do on board if it is good

That board ik about the struggles more why I'm like uhhhh

[naive swan]

All I know is where to connect it

[vocal terrace]

That isn't hard them.

[vocal terrace]

Usb to can adapter it's prone

Prob

PB8/9

U only connect 2 wires this wah fyi

[naive swan]

Yeah I but I know how to use those adapters

Yes just hi and low to the board

Then 24v from the psu

[vocal terrace]

Yee

[naive swan]

Promising just don’t know what the f I’m doing

There is no documentation

[vocal terrace]

Esoterical has documentation

[naive swan]

No on the board part

[vocal terrace]

Just swap to PB8/9 as the can pins for usb to can adapter

[naive swan]

Wait on what part?

[vocal terrace]

Tmrw I can go over the documents better that work? If u have a UTOC that's spare rns tart with it

[vocal terrace]

I'm gonna go to sleep soon lol

But there's the USB pins

Then can pins

Can pins on PB0/1 is common

[naive swan]

Well I got to rewire everything so I’m not there yet anyway

[vocal terrace]

Can bus on PB8/9 is urs

[naive swan]

All this has to go

Gutting it completely

And putting in the Gemini and an ebb36

[vocal terrace]

F

https://mellow-3d.github.io/fly-gemini_v3_can_trouble.html

[naive swan]

Oh nice

Thank you

[vocal terrace]

Give 1 billion dollar or shit ur pants rn

[naive swan]

Sigh

Take the thank you

[vocal terrace]

Lol.

The SHT v2 looks alot better than EBB36

Cause fan voltage of 12v

[naive swan]

I’m not sure, the ebb36 is solid so far

[vocal terrace]

Yea but I need 12V for deltas now

[naive swan]

Man this vhb is strong

12v noctua maybe

[vocal terrace]

Fuck ofd

Noctua not for this

[deep vine]

Salad ratio

[deep vine]

Is this what I need for clockwork 2?

[vocal terrace]

I get from trianglelabs less sketch

@naive swan they put the gundam in gundam tbe witch from mercury this prt

[deep vine]

But do you think it will work until Galileo 2 is released?
Then I will build that with genuine parts?

[vocal terrace]

Yea. But screw Galileo v2 xol2 is way better

[deep vine]

Does it fit in stealthburner?

[vocal terrace]

Yes

[deep vine]

With the sb2240

[vocal terrace]

I'm making mount for XOL sb2240

[deep vine]

What exactly is the XOL

[vocal terrace]

Better cooling

[deep vine]

But you compared it to an extruder

[vocal terrace]

It uses better extruders

[deep vine]

Interesting 🧐

[dawn vapor]

So my printer buzzes

[vocal terrace]

wdym

[dawn vapor]

Stepper buzz all works

[vocal terrace]

good

[dawn vapor]

Now i have to tun sensorless

But before that

[vocal terrace]

RATIO

L

[dawn vapor]

I have a strong suspicion that one of my belts is not a gates

[vocal terrace]

dont do mix match

[dawn vapor]

Even though both bought from same place same spec

[vocal terrace]

thoe look gates

1 has belt wear looks like

[dawn vapor]

The bottom one is def gates

[vocal terrace]

check the fonts vs each other

[dawn vapor]

Has gates written on it

[vocal terrace]

I think the top just looks like has been warn

send photos of em

[dawn vapor]

The black belt has no writing

[vocal terrace]

where u get it from?

[dawn vapor]

West 3d

[vocal terrace]

the sus one?

or bottom

[dawn vapor]

Both

[vocal terrace]

k gonna msg danuiel

[dawn vapor]

Bought at different times

[vocal terrace]

can u send photo of top one?

[vocal terrace]

did u ue the top one?>

[dawn vapor]

Thats the black one

Top

[vocal terrace]

have u used it

[dawn vapor]

Thats the bottom one

The one that looks legit

[vocal terrace]

have u used the seconD/

jun 4

cauyse that would make sense for just wear

[dawn vapor]

No

[vocal terrace]

looks like my V2.4 belt

[dawn vapor]

They had been sitting that long for rhis build

[vocal terrace]

k

[dawn vapor]

Going to buy a new one just think its weird to get two different ones and at the time i was just learning about all this gates and what not

[vocal terrace]

i think it may be gatees just asked.

also don't buy new

wait for response may get refunded

or juts fien

@dawn vapor betcha will be confirmed or refudned

@dawn vapor

i agree

[dawn vapor]

Yeah belt looks fine. Just was sus about it being different than the below one

[vocal terrace]

@dawn vapor u got prob 1 EPDM belt maybe idk yet

it got red text?

@dawn vapor I agree prob with the EPDM

u may have got 1 extra expensive belt on accidewnt

@dawn vapor u cut the non EPDM down?

yea they will replace it msg daniel prob on discord

[dawn vapor]

I did. Not a big deal

[vocal terrace]

they will replace.

[mild hinge]

@naive swan Buddy of mine is looking for the trident feet you hav ea stl for them ?

[naive swan]

yeah on the github

the rubber part?

ot the actual housing?

[mild hinge]

no the 3d printed part

[vocal terrace]

https://tenor.com/view/the-rock-sus-the-rock-meme-the-rock-sus-meme-gif-23972805

[naive swan]

on the github

[mild hinge]

@naive swan housing

[naive swan]

https://github.com/Vprince099/ZANDVE/tree/main/Type-Z/STLs/Skirt/PreBuild_Parts/Corners

[vocal terrace]

guess whos got a bad rapido heater...

again...

[mild hinge]

Thanks I'll forward it to my buddy. I was looking i nthe wrong spot

[vocal terrace]

time to replace it lol. the rapido v2 im waite

[mild hinge]

I need a whole new replacement

[vocal terrace]

wdym?

[mild hinge]

I dont know lingo

[vocal terrace]

what do you mean

[mild hinge]

printer

[mild hinge]

Anyway to put washer back in the CNC part without ripping the whole gantry off the printer ( front Left )

[vocal terrace]

pinmod again?

pinmod...

im having anurism

[mild hinge]

pinmod?

[vocal terrace]

frick whatever send photo

[vocal terrace]

eww those

[mild hinge]

The top shim came out

[vocal terrace]

i liek ramas idlers

[vocal terrace]

WTF how

welp ur belt isn't in there

[mild hinge]

I know I took it out of the way

[vocal terrace]

https://cdn.discordapp.com/attachments/472450547534921729/1093007965889495151/20230404_185110.mp4

[vocal terrace]

i'd remove the red piece. then take out the screw.

then use this and swap back

[mild hinge]

Was trying too

Red piece doesn't appear to come off

[vocal terrace]

bruh that stupid

cnc ewwwww

then ur gonna wanna remove Z motor wires and then use ziptises and loosen the back motor mount and that 1. then make it so can slide fof the front idlers

[mild hinge]

I can slide forward and back still not able to get the cnc apart

Guess Ill just strip the whole gantry off and start over

[vocal terrace]

i don't like cnc stuff for voron lol

[mild hinge]

yea

whole gantry has to come off

[vocal terrace]

F

[mild hinge]

screw it ...ill just junk it

[vocal terrace]

bruh

[mild hinge]

too much of a pain i nthe ass

[vocal terrace]

id just try twizzers and not taking it fof

[mild hinge]

already tried that

[vocal terrace]

not everything is junk.

Ramas Idlers are pog

[mild hinge]

this one is

[vocal terrace]

i think u should just take a break

[mild hinge]

taking a permament one

trash goes out tonight

[vocal terrace]

yes. but like don't

just let it sit

the amount u spent isn't worht going in the trash rn

[mild hinge]

just money

[vocal terrace]

u said working 60 hr

[mild hinge]

yea

[vocal terrace]

u should just save more of that money by letting the machine take it's time

[mild hinge]

I just have one built

looking at LDO kit that is built

[vocal terrace]

just pls listen to me and sit

[mild hinge]

it has been sitting for 6 months

[vocal terrace]

yes.

mine too

[mild hinge]

can have a new built and shipped in 1 week ready to go

[mild hinge]

Yea not ripping off chains/wiring/motors etc

Just ordering new

[vocal terrace]

id jusvt sit wires on the bed

[mild hinge]

Can't

[vocal terrace]

whut

welp don't throw it out mavybe sell it

[mild hinge]

I think I have a offer already

Sent pics

If Don't sell Trash night. I just ordered another one

[vocal terrace]

I'd buy it off u

pls pls pls don't trahs it

[mild hinge]

I'll let you know

[vocal terrace]

@naive swan my roborock is already in the country lol

[mild hinge]

Voron ordered

yea

[vocal terrace]

u get anothe V2?

or trident

trident is easier

[mild hinge]

V2

[vocal terrace]

oof

[mild hinge]

being built

[vocal terrace]

I want trident more

[mild hinge]

why trident

[vocal terrace]

way faster

[mild hinge]

ahhh

as in speed ?

or to build

[vocal terrace]

wspeed and build

[mild hinge]

ok

well its been ordered voron v2

sweet sold

[vocal terrace]

noice

how much?

[mild hinge]

700

[vocal terrace]

ok

[mild hinge]

gave it cheap

[vocal terrace]

yee for sure.

[mild hinge]

out of my space

[dawn vapor]

How long did we decide belts where? 2.3m?

[vocal terrace]

they asking or u?

cause don't pay more lol

ideally try and get another EPDM belt. They are stiffer and like u don't really needa upgrade

[dawn vapor]

I am. I know i dont need 12 meters like bom says. Guess ill re-measure my belt

[vocal terrace]

yea good idea

then add 100mm

[deep vine]

Sexy

[vocal terrace]

why not tell me that ):

[deep vine]

https://tenor.com/view/kagamine-len-love-vocaloid-ratio-project-diva-gif-26179698

[vocal terrace]

https://tenor.com/view/deez-nuts-got-em-deez-nutz-jerk-gif-4967750

[deep vine]

You are ratio king Burgus

Haaaaa

[vocal terrace]

https://www.aliexpress.com/item/1005004121247823.html?spm=a2g0o.order_list.order_list_main.5.40ba1802CBg0yE

ordered 1

[deep vine]

Nice

[vocal terrace]

yee

[deep vine]

Gaurenteed to bend tho, or your money back

[vocal terrace]

cap

look at it

[deep vine]

You should get it anodised, same colour as your frame

[vocal terrace]

no

i like that it's silver

my rail is silver

also frick anodizing thats more money

my Vzbot is gonna be silver frame

[deep vine]

I don’t like the colour tbh, prefer carbon

[vocal terrace]

yes but carbon easier to break

[deep vine]

Probably at high speeds yeh

[vocal terrace]

in general

carbon u know loses stiffness at temps +60

[deep vine]

I’m build CW2 with ecas and ercf tool head sensor

[vocal terrace]

eww

[deep vine]

Yeah because of the the epoxy etc.

[vocal terrace]

yee resin

[deep vine]

https://www.printables.com/model/426754-stealthburner-clockwork2-main-body-with-ecas-and-r

[vocal terrace]

I'd just not have tooldhead

easy

the ERCF doesn't need it

[deep vine]

More tech, more gains

[vocal terrace]

no

it's more friction on filament

[deep vine]

It will be fine

Orbiter will push through it

Well LDO

[vocal terrace]

orbiter u mean shit hehehe

[deep vine]

Name a better option

[vocal terrace]

hevort

vz-hextrudort

sherpa mini

sherpa micro

sailfin

[deep vine]

Still uses a LDO

[vocal terrace]

yes. but Orbiter poo

[deep vine]

It’s actually good

[vocal terrace]

theres a literal encoder wheel so u don't need other stuff

[deep vine]

That’s what Galileo is based on

[vocal terrace]

yes. I'm not going galileo anymroe

cause frick that

going to sherpa mini

[deep vine]

On what

[vocal terrace]

ERCF

[deep vine]

It’s not 100% accurate

[vocal terrace]

should be

theres new toolhead sensorless ercf for a reason

the HARTK pcb doesn't have endstp for that reason

[deep vine]

Someone is working on a new encoder

[vocal terrace]

tradrack better hehe

[deep vine]

Tradrack = 💩

[vocal terrace]

wtf u talking about

[deep vine]

Where’s yours?

[vocal terrace]

its literally 3x better

[vocal terrace]

bruh i only got a E3v2 working....

[deep vine]

Because Voron and track = 💩

[vocal terrace]

theres literally so many people with that config

[deep vine]

It’s not popular

[vocal terrace]

wtf u talking about

I'm literally looking at the tradrack beta channel rn

it is

[deep vine]

Beta for life tho

[vocal terrace]

no

u don't understand annex

[deep vine]

Ercf is alpha

[vocal terrace]

they test shit for a while

[deep vine]

FTW

[vocal terrace]

ERCF is shit.

I say this with 1

[deep vine]

You need to configure better

[vocal terrace]

no

the design is flawed

like litearlly.

[deep vine]

It’s getting better

Then will be 10 times better than T-rack

[vocal terrace]

No lol

[deep vine]

I think so

[vocal terrace]

Tradrack is infinite scale but not ercf for reaosn

[deep vine]

I don’t like the design of the whole motor levering up and down to engage filament

[vocal terrace]

The Roda are an issue

[vocal terrace]

U don't even got 1

It's the same thing hut bigger for trad vs ercf

The tradrack is wayyyy faster too

[deep vine]

It’s moving to 2020

[deep vine]

Hmmm 🤔

When will yours be finished

[vocal terrace]

idk\

[vocal terrace]

bruh.

tradrack is just good

the servo is very powerful

ERCF uses too many components

the d shaft is another failure point

2020 extrusion is the only 1 with tracrack

alot of different linear rails have been sued.

[vocal terrace]

send me photo

or lionk

[mild hinge]

looked squashed to me

I thought so

1st layer looks like crap too

re-run probabe calibrate

this is on a ender 5 pro

I'llsee what it does now

z hanging about 3.7 -3.8

when probing

How about now

[naive swan]

Before

After

[mild hinge]

clean

[vocal terrace]

pog

[mild hinge]

sounds like nozzle hitting certain spots of the print

raised z by 0.01. better

see how it turns out

[naive swan]

Just need to run the canbus wires

[vocal terrace]

noice

DON't UPGRADE TO NEW KLIPPER GUYS

[naive swan]

That may be a problem

[vocal terrace]

canbus is fimne

[naive swan]

I need to put a firmware file on it

Oh ok

What’s wrong with klipper?

[vocal terrace]

voron announcement

[naive swan]

Or the latest build I mean

Ok

[vocal terrace]

idk

but I do't have it

[naive swan]

Checking

Good heads up

[dawn vapor]

um is that why im getting errors installing adxl @vocal terrace

[vocal terrace]

Yes likely

Or with adult harness?

[dawn vapor]

im just trying to update the pi/klipper to be able to use the sb2240 adxl

[vocal terrace]

Remember sometimes ik more then voron electronics

[vocal terrace]

Dog shit results

U should be having issues with other machine

[dawn vapor]

i have a standalone one either way i can't install it

a standalone adxl and harness*

[vocal terrace]

Ur issue is prob that klipper can't connect to ur main mxu

Cause newest version is issue with serial by path ls

[deep vine]

morrning @naive swan

[mild hinge]

Updated klipper...what's wrong with it. I haven't printed anything yet

[mild hinge]

Oh I see the message

[deep vine]

I didn’t even update it and it won’t lent me upload any sliced files :/

[mild hinge]

I updated this morning. I'll check tonight after work

[dawn vapor]

@deep vine did you ever post the nozzle brush purge bucket?

[dawn vapor]

Something with id and file routes i think

[deep vine]

no but its ready

it uses 6 magnets that are 8x3mm

but @dawn vapor i designed this around the 370mmx377mm bed

it might not work with your bed if its bigger

[naive swan]

Ready for canbus programing

[mild hinge]

Sweet beacon will be here today

I'll try it out on ender5pro

[deep vine]

Now have sb2240 and CW2 installed,

[vocal terrace]

L still top gap

Tap

Prob the board

[deep vine]

Yeah, but it was like that before too

It’s not bad tho

Hope board doesn’t give me errors when I start printing

[naive swan]

mine has the same problem

[deep vine]

The wiring management is this board tho is great

[deep vine]

Timer too close?

[deep vine]

Ohh the gap

[vocal terrace]

I dont like the wire management

[deep vine]

Yeah

[naive swan]

I plan on reprinting soon

[vocal terrace]

Common issue

[deep vine]

Warping?

[vocal terrace]

No

Tap has it extra

Cnc tap prob didn't fix it

[naive swan]

Also the neopixels are dead and impossible to remove

So reprinting any way

Mine was good until about 100hrs

[deep vine]

Polymaker or pee-sun

[naive swan]

Abs plus can’t take the heat

[vocal terrace]

Could be rail even

[deep vine]

Oh so heat over time

[mild hinge]

How about ASA

[vocal terrace]

Abs+ is the isuse

[deep vine]

My good friends in America

[naive swan]

I plan on printing in Asa red

[vocal terrace]

I'm canada

[deep vine]

Please who can ship me some red asa

[mild hinge]

Nice

[naive swan]

Lol

[mild hinge]

I really like ASA

Have lp beacon in hand

[naive swan]

Wouldn’t it be expensive to ship the Asa?

[deep vine]

Polymaker doesn’t ship here

[naive swan]

Also doesn’t someone have a line on the vendor from china?

@vocal terrace

[vocal terrace]

Gor what

[mild hinge]

I had polymaker ship ASA to me

[vocal terrace]

Lol

[naive swan]

All the filament is made in china

[vocal terrace]

No

[naive swan]

Some have better qc

[vocal terrace]

Fusion filament is done here

[mild hinge]

unless it says made in america .lol

[vocal terrace]

Well us

[naive swan]

Polymaker

[deep vine]

Yeah send it to me please and thank you

😘

[vocal terrace]

Fabreeko Speedy has run the filament line at fusion filamenrt

[deep vine]

Where you from Mike

[mild hinge]

USA

[vocal terrace]

preempt supposed to help aka 64bit bootloader

[deep vine]

What is that?

The tuequelen

[vocal terrace]

In computing, preemption is the act of temporarily interrupting an executing task, with the intention of resuming it at a later time. This interrupt is done by an external scheduler with no assistance or cooperation from the task.

[deep vine]

Sexy

[deep vine]

It sound complex

[vocal terrace]

not really

[mild hinge]

Now I just need the screw for it and the screw caps

[vocal terrace]

that and doing stock esoterical setup worked

[mild hinge]

gotta be better then the bltouch

[deep vine]

Okay thanks for that info, I’ll have another look into this tomorrow

[mild hinge]

I'll install it this weekend

[deep vine]

Polymaker is a US company

[mild hinge]

yea

where are you located

[deep vine]

A small island north of France

Uk

[mild hinge]

nice

[vocal terrace]

Lol

[deep vine]

😅

[vocal terrace]

Xol2 almost done

[mild hinge]

cool

Ifix it

[deep vine]

Looks like Santa delivered some presents

[mild hinge]

lol

I got my present today too

[deep vine]

That’s what I’m saying lol

[mild hinge]

lol