troubleshooting

bed crashes with initial probe 4 messages

Feb 27, 2024, 2:15 AM Bed Hydra Frame

ACCELEROMETER Battle + Provok3d 18 messages

Feb 25, 2024, 6:26 PM Tuning Firmware Electronics

Layer shifts at the base of the prints 9 messages

Feb 25, 2024, 2:25 PM Print

Crazy Under-Extrusion(?) After Hydra Upgrade 4 messages

Feb 25, 2024, 10:40 AM Hydra Extrusion Print printer

Move out of range error 10 messages

Feb 24, 2024, 10:45 AM Solved printer

issue with bed leveling 63 messages

Feb 19, 2024, 8:05 AM Build Firmware

Y axes input shaping is a nightmare 6 messages

Feb 18, 2024, 12:37 PM Gantry Build Frame Tuning

Stepper towers - Belts movement issues 11 messages

Feb 17, 2024, 10:38 PM Build

need to reflash after Klipper update? 6 messages

Feb 17, 2024, 3:24 PM Firmware

Ztilt problem 76 messages

Feb 17, 2024, 3:08 PM Tuning Firmware

belt resonance related issues. 36 messages

Feb 15, 2024, 7:50 AM Gantry Tuning Frame

My stepper motors work weirdly 5 messages

Feb 12, 2024, 6:10 PM Electronics

Stepper wiring nightmare 7 messages

Feb 6, 2024, 4:34 PM Gantry Build Electronics

Temperature sensor weirdness 8 messages

Feb 5, 2024, 10:00 PM Solved Extrusion

M600 stringing 3 messages

Feb 5, 2024, 1:49 PM Tuning Extrusion

layer shifting 43 messages

Feb 5, 2024, 10:29 AM Tuning Solved Print

Updated klipper on CB1 broke comms with CANBUS ebb36 2 messages

Feb 3, 2024, 12:37 PM Solved Firmware

"Timer too close" error. Canbus bridge Octopus 1.1 111 messages

Feb 2, 2024, 5:47 PM Build Firmware Electronics

Weird Layer Shifts 9 messages

Feb 1, 2024, 4:34 PM Build Tuning

Lost MCU connection randomly 30 messages

Jan 30, 2024, 4:52 PM Electronics

wobbly print 8 messages

Jan 30, 2024, 12:27 AM Tuning

post-set up trouble shooting (belt skipping) 22 messages

Jan 25, 2024, 10:17 PM Gantry Build Tuning Solved

ISP change, and cant get in to mainsail. 7 messages

Jan 23, 2024, 11:01 AM Firmware Electronics printer

Stepper wont go Smooth 42 messages

Jan 22, 2024, 8:44 PM Tuning

Mercury ZeroG Theme 4 messages

Jan 22, 2024, 7:12 PM Firmware

Purge logo 221 messages

Jan 21, 2024, 4:40 AM Bed Extrusion

x and y movement issue 5 messages

Jan 20, 2024, 11:24 PM Build

Changing the board to Manta M8P 4 messages

Jan 19, 2024, 7:16 PM Tuning

Calibration Cube perfect on 3 walls, 4th wall is undersized every time. 116 messages

Jan 19, 2024, 3:45 AM Gantry Tuning Extrusion printer

x and y swapped in mainsail 17 messages

Jan 18, 2024, 10:04 AM Hydra Firmware

end stops not working 8 messages

Jan 16, 2024, 6:50 PM Hydra Firmware

config check 48 messages

Jan 15, 2024, 3:44 AM Build Solved Electronics

X limit switch triggering Z 9 messages

Jan 15, 2024, 2:22 AM Electronics

Sloppy lines 3 messages

Jan 12, 2024, 7:52 AM Print

btt pi wifi 41 messages

Jan 10, 2024, 10:29 PM Electronics

ABS printing at 230 degrees and bed 100. lower surface looks burned 29 messages

Jan 7, 2024, 5:19 AM Extrusion

orbiter V2 sensor+ macros 427 messages

Jan 6, 2024, 12:21 PM Firmware Print printer

z stepper is making squeaking noise 2 messages

Jan 6, 2024, 11:15 AM Tuning Solved printer

ISO Orcaslicer ABS profile 34 messages

Jan 5, 2024, 5:58 AM EVA Print Hydra Tuning Build

Communication timeout during homing X 22 messages

Jan 4, 2024, 9:08 AM Electronics

First layer squish 33 messages

Jan 2, 2024, 10:21 PM Tuning

Blobs? 17 messages

Jan 2, 2024, 5:10 PM Print

Top surface 19 messages

Jan 1, 2024, 11:44 PM Tuning

Sonic pad + original motherboard 7 messages

Jan 1, 2024, 9:06 AM Build Frame printer

Hydra z tilt config 4 messages

Jan 1, 2024, 7:53 AM Bed Hydra

I need to home VERY slowly 16 messages

Dec 30, 2023, 7:25 PM Build Electronics

Spider v2.3 no fans activity and no bed heating. 11 messages

Dec 30, 2023, 2:33 PM Electronics

Print Issues past first layer 4 messages

Dec 29, 2023, 10:53 PM Tuning Solved Print

odd z-axis artifacts 9 messages

Dec 29, 2023, 9:44 PM Tuning Print

Assuming my wiring is good, why won't it extrude? 33 messages

Dec 29, 2023, 9:15 PM Solved Electronics printer