troubleshooting

Weird surface finish issues. 2 messages

Jan 2, 2026, 2:58 PM Print

Movement of X or Y causes other axis to move 2 messages

Jan 1, 2026, 8:26 PM Gantry Tuning printer

Random peaks in Y axis resonance testing 21 messages

Dec 30, 2025, 4:50 PM Hydra Gantry Tuning Frame Build

Top Layer Tuning 2 messages

Dec 24, 2025, 2:15 AM Tuning Extrusion

Head not moving to home position after purge 8 messages

Dec 22, 2025, 3:15 PM printer

Front teethed pulley noise 3 messages

Dec 21, 2025, 7:18 PM Gantry Build Frame

Bed calibration issue 4 messages

Dec 17, 2025, 7:46 AM Bed

Little help 2 messages

Dec 6, 2025, 5:09 PM Tuning Extrusion StealthBurner Print

Z wobble source? 24 messages

Dec 5, 2025, 4:26 PM Print Bed Hydra Tuning Extrusion

New build, first print. Need direction 3 messages

Dec 2, 2025, 6:48 PM Tuning Print

Resonance Issue / Belt Tracking Problem 6 messages

Dec 2, 2025, 5:17 PM Gantry Frame

Intermittent bulging from side of print 7 messages

Dec 2, 2025, 10:22 AM Solved Extrusion Print

Set up ebb36 v1.2 on manta mp8 v2 44 messages

Nov 30, 2025, 4:51 PM Build Firmware Electronics

Help switching to Prusaslicer 4 messages

Nov 26, 2025, 3:56 AM Print

EVA 2.4 Toolhead Flex Caused by High Filament Resistance 9 messages

Nov 24, 2025, 12:30 AM EVA Extrusion

trouble with my zero G xy axis layer shift 13 messages

Nov 20, 2025, 5:57 PM Build Frame

Finally: Troubleshooting for the Mercury Mad Max Tool-changer 48 messages

Nov 17, 2025, 3:25 AM Tuning Extrusion Print printer

z axis off about 1.2mm at start of print. Leveled bed, set z offset for probe, did bed mesh. 3 messages

Nov 11, 2025, 6:40 AM Print Bed Solved Tuning Firmware

Please help. 11 messages

Nov 10, 2025, 2:27 AM EVA Print printer Build Extrusion

Issues with the 2nd layer up. 10 messages

Nov 9, 2025, 9:25 PM Build Tuning

XY coordinates issues 42 messages

Nov 3, 2025, 4:48 PM Bed Gantry Tuning Frame Build

Stepper stall during movement 7 messages

Nov 3, 2025, 12:11 PM Print

Klipper shuts down when I home 4 messages

Nov 1, 2025, 7:54 PM Build Firmware

New print issue Extreme layer shift? 50 messages

Oct 26, 2025, 9:12 PM Tuning Build

Pi Crashing at random times. 2 messages

Oct 12, 2025, 5:02 AM Electronics

Fans not working on new install 26 messages

Oct 10, 2025, 9:49 PM Build Electronics

Y axis sensorless homing issue 27 messages

Oct 6, 2025, 6:56 PM Gantry

Printer shutdown halfway through "Lost connection with MCU" 7 messages

Oct 5, 2025, 11:56 PM Electronics

can anyone reconize the cause of this furry bed mesh? 29 messages

Oct 2, 2025, 1:48 AM Bed Tuning Electronics printer

Thermocouple reader fault on new hotend setup 3 messages

Sep 29, 2025, 10:00 AM Electronics

Flow test outcome shows single line holes at <10mm3/sec 27 messages

Sep 28, 2025, 9:17 PM Tuning Extrusion Solved

z axis problems hard to explain 8 messages

Sep 27, 2025, 10:48 PM Tuning

ok I'm at wit's end 14 messages

Sep 24, 2025, 12:45 AM Firmware

Bad extrusion Solved 23 messages

Sep 23, 2025, 3:24 PM Tuning Extrusion

eva 2.4 sherpa mini 15 messages

Sep 22, 2025, 3:18 AM EVA

Constant layer shifts 52 messages

Sep 20, 2025, 3:57 AM Gantry Build Tuning printer

V2.2 MB with BTT u2c/ebb36 g0b1 CAN troubleshooting Rpi Klipper/Mainsail 8 messages

Sep 18, 2025, 5:12 AM Firmware

Rattling while printing 4 messages

Sep 15, 2025, 6:28 AM Build EVA printer

Need help with flashing Klipper to EBB36 20 messages

Sep 15, 2025, 12:03 AM Build Firmware

Is my mount wrong for a Rapido hot end? 2 messages

Sep 13, 2025, 1:36 PM Solved EVA

Failing prints due to bad first layer [solved] 5 messages

Sep 9, 2025, 10:00 PM Print

Squeaky Merc 30 messages

Sep 8, 2025, 1:07 AM Gantry Build Tuning

help with a/b motors 4 messages

Sep 5, 2025, 1:17 PM Gantry Build Electronics

Inconsistent walls 4 messages

Sep 4, 2025, 8:46 PM Tuning

Cartographer issues? 13 messages

Sep 2, 2025, 11:06 AM Bed Solved

New build, trouble homing 5 messages

Aug 31, 2025, 12:16 AM Build

First layer issues??? 3 messages

Aug 30, 2025, 8:47 PM Print

Is my merc dying? 2 messages

Aug 20, 2025, 6:54 PM Print

Off center 4 messages

Aug 8, 2025, 9:24 PM Tuning Print printer

Issue accessing the heightmap panel 2 messages

Aug 3, 2025, 9:12 AM Firmware