troubleshooting

No trigger on probe after full movement - Merc One.1 (5+) with Hydra 18 messages

Dec 27, 2022, 1:23 PM Bed Build

Dowel pin holes are too big 5 messages

Dec 26, 2022, 8:16 PM printer

input shaper tuning help 74 messages

Dec 24, 2022, 9:59 AM Tuning

Issue with right stepper tower 11 messages

Dec 20, 2022, 1:54 AM Build Solved

homing issue 4 messages

Dec 17, 2022, 9:25 AM Hydra Gantry Frame printer Build

ASA WarpingAdhesion Issues - Any Suggestions? 11 messages

Dec 16, 2022, 10:58 PM Tuning Print

ASA printing tuning help. 21 messages

Dec 16, 2022, 9:55 PM Tuning Print

Mercury one belts & gantry truing issues 19 messages

Dec 11, 2022, 5:32 PM Build Frame Tuning

extrusion-flow calibration cura 9 messages

Dec 10, 2022, 9:00 PM Tuning Extrusion

Strange issue with extrusion, positioning, or something else 31 messages

Dec 9, 2022, 9:40 AM Gantry Tuning Extrusion

webcam setting went out 50 messages

Dec 8, 2022, 4:44 AM Solved Firmware

did I do this right? 16 messages

Dec 3, 2022, 3:20 AM Solved Extrusion

BTT ebb36 and u2c on Orangepi zero2 10 messages

Nov 30, 2022, 4:09 AM Build Firmware Electronics

Linear Rail Centring Guides 4 messages

Nov 28, 2022, 8:50 PM Solved Gantry Frame Build Extrusion

printing issue 14 messages

Nov 27, 2022, 2:41 PM Print printer

calibration issue 38 messages

Nov 26, 2022, 11:52 PM Tuning Print

5+ spacers not enough for me. 15 messages

Nov 26, 2022, 7:52 PM Bed Solved

Bed leveling, Hydra, 5+ 13 messages

Nov 26, 2022, 6:21 PM Bed

Changing direction in X or Y is bumping the opposite direction. VIDEO 8 messages

Nov 23, 2022, 9:24 PM Gantry Build Frame

Brittle motor mount towers 138 messages

Nov 23, 2022, 5:27 AM Solved Extrusion

Bed looking like a mountain 10 messages

Nov 21, 2022, 5:45 PM Bed Tuning

loose bearing stacks? 23 messages

Nov 21, 2022, 12:42 AM Solved printer

z1 moving faster than z1 5 messages

Nov 21, 2022, 12:14 AM Bed Tuning Electronics Build

Movement sounds Gantry 19 messages

Nov 20, 2022, 5:48 PM Gantry

ebb36 pt1000 max31864 problem 184 messages

Nov 20, 2022, 4:57 PM Firmware Electronics

EBB36 issue 18 messages

Nov 18, 2022, 4:42 AM Electronics

buzzing before homing 3 messages

Nov 16, 2022, 2:35 AM Build Tuning Electronics printer

hydra print tuning 23 messages

Nov 14, 2022, 1:56 PM Tuning Solved

Warped frame rails? 90 messages

Nov 14, 2022, 12:32 AM Bed

I am not able to print decent parts 138 messages

Nov 13, 2022, 8:56 AM Tuning Extrusion Print

hydra z tilt issue 7 messages

Nov 7, 2022, 3:43 AM Bed printer

Calibration help 3 messages

Nov 6, 2022, 8:32 AM Print Hydra Tuning Firmware Extrusion

Bed Heater cable management 6 messages

Nov 5, 2022, 10:31 PM Bed

Weird Input Shaper results 114 messages

Nov 4, 2022, 3:43 PM Build

Cannot dial in print setting after upgrade to Mercury 39 messages

Nov 3, 2022, 4:02 PM Tuning Extrusion

Hydra Z-Tilt Right Z 60 messages

Nov 3, 2022, 3:54 AM Build Frame

BL Touch fuckery 249 messages

Nov 2, 2022, 11:16 AM Firmware

Underextrusion or something else? 6 messages

Nov 1, 2022, 4:25 PM Extrusion

Despair 15th failed attempt printing mosquito EVA mount plate (heavy overhangs off thin sides) 4 messages

Oct 31, 2022, 3:29 PM Build Print

Weird blobs in corners 48 messages

Oct 29, 2022, 9:53 AM Extrusion

Too much wooble? 26 messages

Oct 28, 2022, 9:29 AM Tuning Frame StealthBurner

Ender 5 Plus - Mercury One.1 Issue 4 messages

Oct 28, 2022, 4:43 AM Solved

Z steppers give high pitch 25 messages

Oct 27, 2022, 5:36 PM Bed Hydra Firmware

Cracked Stepper Mount 14 messages

Oct 26, 2022, 12:45 PM Build

BTT Octopus 1.1 Stepper humming + not moving 16 messages

Oct 25, 2022, 9:41 AM Build Firmware Electronics

Blobs on prints 4 messages

Oct 23, 2022, 11:38 PM Extrusion

rapido heater issue 20 messages

Oct 23, 2022, 5:45 PM Build Extrusion Electronics

Skr 1.4 turbo not flashing 30 messages

Oct 23, 2022, 10:49 AM Firmware

Extruder motor skipping after getting very hot 2 messages

Oct 22, 2022, 12:04 AM Extrusion Electronics

A bit of a Loaded Question about upgrading my Ender 5 Plus with a Core XY setup 9 messages

Oct 18, 2022, 9:32 PM Build