printing-forum

3598 threads · Page 5 of 72

✅ - Need Help Printing TPU on K1Max 10 messages
slicer print quality printing printing problem
✅ - Printer problems 10 messages
hardware printing printing problem
How to avoid nozzle clogging and burnt pla? 38 messages
hardware printing problem
Any idea how to fix this? 28 messages
hardware printing problem fdm
Not good first layer 52 messages
fdm print quality printing recommendation
Prints speed 6 messages
slicer
✅ - Speed 5 messages
slicer
Print quality elegoo Neptune 3 max 15 messages
print quality
What Filament Should I Use? 9 messages
print quality printing recommendation
Top Most Layer Lines 6 messages
print quality printing problem
Fixing a print 9 messages
fdm printing
✅ - Infill strength issue 7 messages
printing recommendation
✅ - Indio strength issue 2 messages
printing recommendation
Help scaling motorized helmets 6 messages
printing recommendation
✅ - Sizing help 15 messages
slicer recommendation
I need help, my print keeps falling off the baseplate when nearing the end of the print 7 messages
printing printing problem
Elagoo Neptune 3 Max just stops feeding? 23 messages
hardware printing printing problem
Strange resin printing failures 9 messages
resin printing printing problem
Ender 3 Homing issue. 2 messages
hardware
CR10 V3 ghosting/ringing on edges so bad, what could be the cause(s) 8 messages
fdm print quality printing printing problem
K1 Filament Twisting/Clog 10 messages
fdm printing problem printing
Bed not connecting to nozzle ender 5 7 messages
hardware print quality printing problem printing recommendation
Help! 7 messages
hardware printing fdm
Why does this happen? 70 messages
fdm print quality printing printing problem
Need help with Calibration 3 messages
print quality printing printing problem fdm recommendation
✅ - Help me figure out what I need to calibrate 19 messages
hardware print quality printing printing problem fdm
✅ - Just replaced the hot end and now cant get past the first layer. Any ideas? 5 messages
print quality printing problem
EZABL™ NG Bed Leveling Kit for Creality Ender 3/3 Pro firmware 6 messages
printing problem
Need help 3 messages
printing problem
Red Hood Helmet Help 36 messages
fdm slicer printing problem
first layer keeps making my printer jam 110 messages
printing problem
Error with slicing and printing the solo leveling daggers 20 messages
fdm slicer printing problem
✅ - Ender 3 s1 boot loop 9 messages
printing problem
Ended 3 metal bed pealing 19 messages
hardware
Why is this happening 4 messages
printing printing problem
Printer advice 3 messages
printing recommendation
Anyone know how to fix Orca Slicer crashing when slicing the print? 13 messages
fdm slicer
what is happening here? 3 messages
fdm print quality printing problem printing
Printer advice 2 messages
print quality printing recommendation
✅ - PTFE Ender 3 v1 34 messages
printing problem
Neptune 3 Max - Layer Shifts/Wobbles 5 messages
fdm print quality printing printing problem
Best Orca Slicer setting for a Sovol Sv07 Plus 5 messages
slicer print quality printing recommendation
✅ - What am I doing wrong? 16 messages
fdm print quality printing problem
Raft is lifting 6 messages
fdm print quality printing printing problem
Ender 3 starts underextruding after being like 80% done with print 4 messages
print quality printing problem
First Time Printing with TPU 15 messages
print quality printing recommendation
✅ - Neptune 3 plus nozzle is making loud noises and vibration 12 messages
fdm printing printing problem
Is this an extrusion issue? 28 messages
fdm print quality printing problem printing
Any idea how I could fine tune my printer to avoid these later lines toward the top of the head? 12 messages
resin print quality printing printing problem recommendation
Anyone know what caused this layer fail? 6 messages
print quality printing problem printing fdm recommendation