I can't seem to get Z to work properly | Reprapfirmware, DSF and DWC | Page 1

tawny lava Sep 19, 2023, 7:14 AM

#

Here's my M122 output - this is new to me - :
M122
=== Diagnostics ===
RepRapFirmware for STM32H7 based Boards (biquskr_3_ez_h723) version 3.5.0-rc.1+102 (2023-09-05 23:17:13) running on STM32H723 (standalone mode)
Board ID: L0001-082KA-D43WN-6R1DG-WF6XX-70000
Used output buffers: 3 of 40 (27 max)
=== RTOS ===
Static ram: 44072
Dynamic ram: 87752 of which 0 recycled
Never used RAM 114968, free system stack 112 words
Tasks: NETWORK(2,nWait,9.8%,224) HEAT(3,nWait,0.0%,350) Move(4,nWait,0.0%,256) CanReceiv(6,nWait,0.0%,431) CanSender(5,nWait,0.0%,337) CanClock(7,delaying,0.0%,333) TMC22xx(4,nWait,0.7%,147) FSWRITE(2,nWait,0.0%,567) MAIN(1,running,89.2%,1131) IDLE(0,ready,0.3%,30), total 100.0%
Owned mutexes: WiFi(NETWORK) BITIO(TMC22xx)
=== Platform ===
Last reset 00:04:53 ago, cause: software
Last software reset at 2023-09-19 00:08, reason: User, Gcodes spinning, available RAM 114968, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
MCU temperature: min 49.6, current 53.2, max 53.2
Supply voltage: min 24.0, current 24.0, max 24.0, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill 2209, SG min 38, reads 24356, writes 17, error r/w 0/1, ifcnt 38, timeout 0
Driver 1: standstill 2209, SG min 14, reads 24356, writes 17, error r/w 0/1, ifcnt 38, timeout 0
Driver 2: not present
Driver 3: standstill 2209, SG min 14, reads 24356, writes 17, error r/w 0/1, ifcnt 42, timeout 0
Driver 4: standstill 2209, SG min 0, reads 24360, writes 13, error r/w 0/1, ifcnt 27, timeout 0
Driver 5:
Driver 6:
Driver 7:
Driver 8:
Driver 9:
Driver 10:
Driver 11:
Driver 12:
Driver 13:

#

Date/time: 2023-09-19 00:13:48
Slowest loop: 3.60ms; fastest: 0.03ms
=== Storage ===
Free file entries: 20
SD card 0 detected
SD card longest read time 2.6ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, segments created 3, maxWait 142990ms, bed compensation in use: none, height map offset 0.000, ebfmin 0.00, ebfmax 0.00
no step interrupt scheduled
Moves shaped first try 0, on retry 0, too short 0, wrong shape 0, maybepossible 0
=== DDARing 0 ===
Scheduled moves 10, completed 10, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== DDARing 1 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Movement locks held by null, null
HTTP is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
File2 is idle in state(s) 0
Queue2 is idle in state(s) 0
Q0 segments left 0, axes/extruders owned 0x80000007
Code queue 0 is empty
Q1 segments left 0, axes/extruders owned 0x0000000
Code queue 1 is empty
=== CAN ===
Messages queued 2635, received 0, lost 0, boc 528
Longest wait 0ms for reply type 0, peak Tx sync delay 0 free buffers 50 (min 50), ts 1465/0/0
Tx timeouts 0,0,1193,0,0,904 last cancelled message type 0 dest 1

#

=== Network ===
Slowest loop: 25.09ms; fastest: 0.00ms
Responder states: MQTT(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0)
HTTP sessions: 1 of 8
Uploads/Errors: 0/0
=== WiFi ===
Interface state: active
Module is connected to access point
Failed messages: pending 0, notrdy 0, noresp 0
Bad header: 0/0
Firmware version 1.27-04S32-D
MAC address b4:75:0e:63:da:95
Module reset reason: Turned on by main processor, Vcc 0.00, flash size 4194304, free heap 143588
WiFi IP address 192.168.1.79
Signal strength -21dBm, channel 9, mode 802.11n, reconnections 0
Clock register 00002003
Socket states: 0 0 0 0 0 0 0 0

queen lintel Sep 19, 2023, 7:16 AM

#

Driver 2: not present

tawny lava Sep 19, 2023, 7:16 AM

#

That's not good is it

queen lintel Sep 19, 2023, 7:17 AM

#

no. time to revisit that driver

tawny lava Sep 19, 2023, 7:17 AM

#

does that mean the driver plugged into the board

#

I'm using those EZ drivers

queen lintel Sep 19, 2023, 7:19 AM

#

i would swap drivers 2 and 3 and see what RRF reports

#

remember to do so with the power off

tawny lava Sep 19, 2023, 7:19 AM

#

OK. I will do that. THANK YOU for mentioning the last part.

#

done. firing back up

queen lintel Sep 19, 2023, 7:23 AM

#

what does M122 say now?

tawny lava Sep 19, 2023, 7:26 AM

#

=== Network ===
Slowest loop: 25.09ms; fastest: 0.00ms
Responder states: MQTT(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0)
HTTP sessions: 1 of 8
Uploads/Errors: 0/0
=== WiFi ===
Interface state: active
Module is connected to access point
Failed messages: pending 0, notrdy 0, noresp 0
Bad header: 0/0
Firmware version 1.27-04S32-D
MAC address b4:75:0e:63:da:95
Module reset reason: Turned on by main processor, Vcc 0.00, flash size 4194304, free heap 143588
WiFi IP address 192.168.1.79
Signal strength -21dBm, channel 9, mode 802.11n, reconnections 0
Clock register 00002003
Socket states: 0 0 0 0 0 0 0 0

#

you probably want this part?

#

Driver 0: standstill 2209, SG min 0, reads 13076, writes 13
Driver 1: standstill 2209, SG min 0, reads 13076, writes 13
Driver 2: standstill 2209, SG min 0, reads 13076, writes 13
Driver 3: standstill 2209, SG min 0, reads 13076, writes 13
Driver 4: standstill 2209, SG min 0, reads 13075, writes 13
Driver 5:
Driver 6:
Driver 7:
Driver 8:
Driver 9:
Driver 10:
Driver 11:
Driver 12:
Driver 13:

queen lintel Sep 19, 2023, 7:26 AM

#

must not have been seated properly

tawny lava Sep 19, 2023, 7:27 AM

#

does this mean i got a bad ez driver?

queen lintel Sep 19, 2023, 7:28 AM

#

no, they're being read fine now. give it a try

tawny lava Sep 19, 2023, 7:30 AM

#

give what

#

home z

queen lintel Sep 19, 2023, 7:30 AM

#

see if both z steppers work

tawny lava Sep 19, 2023, 7:31 AM

#

ok i'm sending g92 z0

#

now from dashboard sending z+5

#

HOLY THAT WORKED

#

That looked so smooth I am geeking out like Sam Tripoli right now

#

ok gonna try to home z

#

if I can do this I can autolevel the bed then I'm off to the races

#

probe went to middle of bed then bed started going south

#

had to emergency re-start

#

reversed z motors (i think)

#

The only issue seems to be that the bed goes up and hits the probe but it does triegger. Trigger height I'm thinking?

queen lintel Sep 19, 2023, 7:45 AM

#

why do you have an M558 H30 line in your config?

tawny lava Sep 19, 2023, 7:45 AM

#

not sure what that is, let me check

#

have this

#

M558 P9 H10 F300:100 T8000 C"^probe" ; set Z probe type to bltouch and the dive height + speeds H=dive height; F=probing speed; T=travel speed
;;M558 Set Z probe type: P9=BLTouch that needs to be retracted and redeployed between probe points
;;M950 S0 C"Servo0" ; Setup Servo0 as servo port on SKR3EZ H723
; Miscellaneous
T0 ; select first tool

queen lintel Sep 19, 2023, 7:55 AM

#

look higher up

#

you have the probe settings twice

tawny lava Sep 19, 2023, 7:55 AM

#

hmm

queen lintel Sep 19, 2023, 7:55 AM

#

when the bltouch is retracted, does it show as 1000 in the interface?

tawny lava Sep 19, 2023, 8:05 AM

#

After I ran 'alarm release + pin' it does

#

sry

#

shows 0

#

is this what u mean

#

queen lintel Sep 19, 2023, 8:07 AM

#

it should show 1000 when the pin is in and 0 when its out

tawny lava Sep 19, 2023, 8:08 AM

#

I've got z probe at zero when it is in

queen lintel Sep 19, 2023, 8:08 AM

#

If it never changes then you need to check your wiring

tawny lava Sep 19, 2023, 8:09 AM

#

when I click pin down (macro) it causes the pin to extend

#

but still says z probe is at zero

queen lintel Sep 19, 2023, 8:09 AM

#

There's 2 sides to a bltouch, the servo, which in your case is working, and the switch side, which isn't

#

So you need to investigate the black and white wires from the switch

tawny lava Sep 19, 2023, 8:11 AM

#

my mind is blown. what do you want me to do

#

all the macros are working

queen lintel Sep 19, 2023, 8:11 AM

#

Check the wiring

tawny lava Sep 19, 2023, 8:11 AM

#

i don't understand

queen lintel Sep 19, 2023, 8:11 AM

#

Well the wiring is obviously wrong

tawny lava Sep 19, 2023, 8:11 AM

#

if i can hit the macros and make the pin go up and down?

queen lintel Sep 19, 2023, 8:12 AM

#

Right

#

That's the servo

#

That's nothing to do with the switch side of the bltouch

tawny lava Sep 19, 2023, 8:12 AM

#

ok. So theoretically I could switch the white and black wires?

queen lintel Sep 19, 2023, 8:13 AM

#

Not really. Black is ground, white is the probe pin

tawny lava Sep 19, 2023, 8:15 AM

#

M584 X0 Y1 Z2:3 E4

#

is this what it should look like

queen lintel Sep 19, 2023, 8:15 AM

#

That's fine

tawny lava Sep 19, 2023, 8:16 AM

#

thx jay

#

gonna send it

#

ok. 2 be clear what's going on is

#

when i hit "home z" the bed (on ender 5 plus) goes up as expected

#

but when the bed hits the probe it does not trigger

#

and a bad noise ensues

#

until i hit emergency stop

queen lintel Sep 19, 2023, 8:19 AM

#

right, because your probe isn't working properly, probably due to a wiring fault

#

i'm not sure how else to say it

tawny lava Sep 19, 2023, 8:21 AM

#

i just flipped the wires around

#

on the red brown yellow part

queen lintel Sep 19, 2023, 8:22 AM

#

the red brown yellow part is the servo part that was working

#

now it won't

tawny lava Sep 19, 2023, 8:22 AM

#

i'm thinking if I can control the probe through the macros, how can there be a wiring fault

queen lintel Sep 19, 2023, 8:22 AM

#

i will say this again, there are 2 parts to a bltouch

#

the servo part that deploys and retracts the pin that you did have working

#

then, theres the detection part that doesn't work

#

you need to investigate the BLACK AND WHITE WIRES

tawny lava Sep 19, 2023, 8:23 AM

#

ok

#

just flipped those around using hand force

queen lintel Sep 19, 2023, 8:23 AM

#

DO NOT mess about with the others as that part is (although not anymore) working

tawny lava Sep 19, 2023, 8:24 AM

#

pin up - pin down still working

#

trying pin z

#I can't seem to get Z to work properly