Hello, I am trying to level the bed to my Creality CR10s pro v2 and I keep taking the bed-leveling nuts off on accident while twisting because the bed doesn't go high enough to touch the nozzle. What do I do?
This is my first printer and I am a little lost.
#Please help me
turbid jewel
grand lion
Are you sure your Z is at 0 when you level? If you mean when you start a print its off thats a mix of Startscript in theslicer and z offset
@turbid jewel
turbid jewel
I don't know what I am doing T.T
People are telling me to move the z axis switch down a little but I can't even find it
grand lion
Who? Because you have none
You have a bltouch on the left of your printhead.
And if you home your printhead will notstop at Zaxis 0mm but somewhat Of 5mm to 50mm
You need to manualy lower that to 0
grand lion
turbid jewel
I was watching that but the problem is that where he puts the 2mm under the nozzle his printer touches it while my bed is too low and when I go to make it higher the nuts fall off because they reach the limit
and its still not touching
grand lion
Take an image of your issue and one of whats your printer display shows
grand lion
Okay go back to the normal menue and to the menue where you csn manually move your axis
turbid jewel
Done
grand lion
Is it closer to the bed or still at the same height?
turbid jewel
Still the same
grand lion
Hmm maybe is a creality moment ... turn your printer off and on and try homing again 🙂
turbid jewel
Okay 😭
grand lion
Na that can happen that sometimes positions get lost
turbid jewel
I just redid the whole thing after turning it off and on and its still the same
turbid jewel
They are all loose
grand lion
Hmm go back to the leveling mode inter face and hit the house button there
Did it work?
grand lion
The z axis didnt move?
turbid jewel
The nozzle is still way too high
grand lion
Maybe but was there any movement at all?
turbid jewel
Sadly I don't see a difference
grand lion
So when you hit home z there was 0 movement?
turbid jewel
Yeah
grand lion
No clicking sound or so?
turbid jewel
It moves and does the whole Home process but there is no change in distance between the bed and the nozzle
grand lion
Hmm okay so there is a button -z how far can you go down?
turbid jewel
with one click its as low as it should be
actually it needs a little more
there is still too big of a gap
grand lion
2 to 5 mm are okay
Anyway get it as close as possible with the -z command and then restart your printer
Then check if its at z zero and go further down 🙂
turbid jewel
I restarted, its at 0, do I try leveling again?
grand lion
No go further down 🙂 till you are in reach of the bed
turbid jewel
It doesn't go further down than zero
grand lion
... okay then manuall method
Turn your printer off and move it down by turning the lead screws
Just make sure left and right are at the same height
turbid jewel
Alright, its done
grand lion
So you are at a workable height now?
grand lion
I hope not. If you home your printer now does the probe deploy?
grand lion
And what shows z? It should be +5 or so now
turbid jewel
It says 10.0
grand lion
Good 🙂 now move z to 0 and try thr leveling 🙂
wet void
stuck on nearly the same problem.....
grand lion
The problem is usally for security the nozzle cant move below -5 on z
To prevent crashes
And i guess thats whats happwnd
turbid jewel
Thank you so much and sorry for wasting so much of your time!
grand lion
No problem wanna fix the next problem too?
B3cause the start script in cura is usally bad so your autobed level wont work 😄
turbid jewel
I am using crealityslicer, haven't had an issue yet
grand lion
That is old cura with a creality sticker but if it works i wont say anything
turbid jewel
I can always come back xD
