#Issue with running the Lua script on Taranis QX7 equipped with a RadioMaster Ranger Micro ELRS modul

74 messages · Page 1 of 1 (latest)

cunning brook
#

Hello,

I am sending this message because I recently bought a drone equipped with an RX ELRS. Since I have a Taranis QX7 transmitter, I purchased a RadioMaster Ranger Micro ELRS module.
I updated the firmware of my transmitter and the RadioMaster to the latest version. I also added the elrsV3.lua file to my transmitter.
When I run the .lua file on my transmitter, the behavior is strange.
Sometimes it gets stuck on "Loading..." indefinitely.
Sometimes the script starts without any issues.
And sometimes I have to wait a few minutes.
So, I don't understand where the problem could be coming from.

Has anyone seen this before, please ?

Thank you in advance 😉

thorn glen
#

reflash the ranger micro via uart/usb with erase before flash enabled

#

and do the crossfire/inverter mod on your QX7

#

or get a better radio

cunning brook
#

Thank you @thorn glen for the advice, I will try to apply it this afternoon and keep you updated.
From what I understand, the QX7 transmitter is not recommended in this field 🙂 Which one would you recommend, please?

thorn glen
#

T20 for a much slimmer profile..

#

there's the T15 too for colored screen, but still in that same form-factor

#

all of these have the ExpressLRS internal module versions

hazy cave
#

I went from the QX7 to the Boxer, it's similar in the ways that mattered to me, but also a lot better in most

cunning brook
#

I'll try to get my QX7 working, and if it's impossible, I'll consider switching to another transmitter.
Thanks for the advice, it gives me a good perspective!

hazy cave
cunning brook
#

Hello @thorn glen @hazy cave ,

I was able to apply the advice you gave me yesterday, and I finally managed to get the ELRS module working on my transmitter. I noticed that when I powered my transmitter with batteries, I had power issues with the Radiomaster module, which were resolved by using a battery to power my transmitter.

Thank you for your help.

thorn glen
cunning brook
thorn glen
#

e.g. if on your flights you're not really using 1W, then set it down to a reasonable level.. and use dynamic power

#

or use better battery packs on the radio in the first place

cunning brook
gaunt flower
#

@hazy cave i am running the qx7 without the mod but with the 1 bit mode, It Is working fine for now, what are the advantages of the mod

hazy cave
#

Higher speed

gaunt flower
#

On loading or latency

#

Or you were Just able tò go higher baudrat?

hazy cave
#

Without it I think you're limited to 115k or 400k

#

You need more to do 500Hz packet rate

hazy cave
#

I wanted 500hz packet rate

gaunt flower
#

For the mod?

hazy cave
#

There are images

gaunt flower
#

I already have the price

#

Piece

gaunt flower
gaunt flower
hazy cave
#

Just search "QX7 Crossfire mod"

gaunt flower
gaunt flower
#

K hahahah

hazy cave
#

I got rid of the QX7 not much later after doing the mod anyway

gaunt flower
#

Since me switching would lead tò somethink like the One you have (and i think you spent a lot)

#

Hahaha

gaunt flower
hazy cave
hazy cave
gaunt flower
gaunt flower
#

Get stuck

#

Like if It crashes

#

But remain stuck forever

hazy cave
#

are you certain you did the mod correctly?

gaunt flower
#

I am taking some photo in a second

#

This are the One Easy tò make and then there Is the last One

gaunt flower
#

For the Blue One

hazy cave
#

can you get a photo of the other side too?

gaunt flower
#

I am the dumbest guy ever

#

Whtf

#

In my chip 2 cable were inverted

#

I probably got lucky

#

But Will se

#

See

hazy cave
#

it's all 3.3V logic, shouldn't've fried anything

gaunt flower
#

K Is now working and i can get 900k baud without One bit mode

gaunt flower
#

Working also at more than 900l

#

K