gleaming obsidian
First off, my other ELRS TX Nano Module from Happymodel works totally fine, but with this BetaFPV one the lua gets stuck at loading...
I tried v2.5.1 and latest 3.1.2, both flash successfully and the wifi hotspot works too but the lua doesn work at all.
There has been a bug report, but their workaround doesn't work on my end.
brave trout
Which module is it exactly? Can you show the ELRS Configurator options you used to flash?
gleaming obsidian
its a BetaFPV 2400 TX Nano
brave trout
How are you getting it into WiFi mode if the lua doesn't load?
gleaming obsidian
I plug it in and wait 60 seconds
brave trout
So it's not connected to the handset
Do you have a model loaded with internal rf set to off and external rf set to crsf?
!externalrf
gleaming obsidian
yes, as said my happymodel module works fine
brave trout
Open up the TX module and make sure no pins are broken/disconnected
gleaming obsidian
oh ok
brave trout
It's acting like the S.Port pin is not connected
Assuming the module lights up when plugged into the radio
If it was receiving a response from the radio on the SPort pin it wouldn't go into wifi mode
gleaming obsidian
pin 4 is connected to that small smd thingy so I cant check if it is connected all the way through
but all other pins are properly connected through a cable to the main board
oh and I cant seem to beep through pin 5 either
brave trout
You're only concerned with the bottom three pins
VBat, GND, and SPort
If the module is powering up in the bay, it's the SPort pin that is questionable
gleaming obsidian
those 3 yellow ones are connected to cable pin 1, 2 and pin 3 is on cable pin 4 & 5
I don't see anything wrong with the board
except maybe they could've used more solder
seems like this is a software problem after all: https://github.com/ExpressLRS/ExpressLRS/issues/2010
brave trout
seems like this is a software problem after all: https://github.com/ExpressLRS/E...
Are you using a FlySky TX?
gleaming obsidian
no
but the issues are all on BetaFPV modules
also the button on the module to change output pwr isn't working anymore since I flashed to elrs 3
brave trout
Have you flashed your module back to 3.0.1 and confirmed that fixes it?
gleaming obsidian
Have you flashed your module back to 3.0.1 and confirmed that fixes it?
tried, did not fix it
gleaming obsidian
I know that at least the button on the module was working before, but unfortunately I never checked if the module itself was working before I flashed it
swift lantern
Hi, in order to get mine working I had to use betaflight Passthrough. use ExpressELRS 1.5.3 because Newest Version is Bugged
that seems to be the onlyway
also you're flashing Micro and not NanoRX
if you have the Nano you need to Use the NanoRx Version on ELRS Config 1.5.3
working as of 1am this morning @gleaming obsidian
gleaming obsidian
if you have the Nano you need to Use the NanoRx Version on ELRS Config 1.5.3
that was a mistake I made on this screenshot, I did flash the nano version
swift lantern
did you try 1.5.3
gleaming obsidian
did you try 1.5.3
I'am trying, have to put it together first xD
gleaming obsidian
<@360412125274963978> Custom drone?
yes
gleaming obsidian
Hi, in order to get mine working I had to use betaflight Passthrough. use Expres...
where do I get the 1.5.3 version from?
gleaming obsidian
no I mean the 1.5.3 that i should flash
oh u mean the configurator is bugged?
which elrs version did you flash to you module?
swift lantern
I had to Flash 2.5.1 First
rigid ibex
