fix-my-printer

Can't set Z Offset 56 messages

Aug 1, 2024, 1:55 PM motion Solved

Print cooling fan isn't working 12 messages

Aug 1, 2024, 9:50 AM other setup

MCU Negative Temp Error. 3 messages

Aug 1, 2024, 8:05 AM setup

RatOS 2.1 Kraken V-Core 3.1 confused on what to do next. 7 messages

Jul 30, 2024, 7:59 PM setup

4028 Tripping 12V Rail 7 messages

Jul 30, 2024, 3:09 PM other

Strange clicking sound on moves VCore4 300 Hybrid 11 messages

Jul 30, 2024, 2:03 PM motion Solved

Orbiter keeps giving random false runouts 12 messages

Jul 29, 2024, 2:10 PM other

Y Axis (maybe x too?) not moving 3 messages

Jul 29, 2024, 10:10 AM motion setup

Beacon connector sitting lower than the nozzle VCore 4 5 messages

Jul 28, 2024, 10:48 PM motion Solved setup

Raspberry pi keeps broking 5 messages

Jul 26, 2024, 6:46 PM setup

4028 Fan Config, updating from VCore 3.1 to new Toolhead V1.0 with RatOS 2.1 16 messages

Jul 26, 2024, 12:14 PM Solved setup

No Beacon model loaded 19 messages

Jul 25, 2024, 12:32 PM motion other setup

MCU Protocol Error 16 messages

Jul 24, 2024, 10:37 PM Solved other setup

Password is not raspberry 14 messages

Jul 24, 2024, 8:59 PM Solved other setup

Reassign Motor to new slot 7 messages

Jul 22, 2024, 10:50 PM motion Solved

very inconsistent first layers on VC4 10 messages

Jul 20, 2024, 10:17 PM other

Octopus Pro V1.1 25 messages

Jul 19, 2024, 6:27 PM Solved setup

3DO Nozzle Camera Help 4 messages

Jul 19, 2024, 3:49 PM Solved setup

Left belt seize/jump/binds through motion 4 messages

Jul 16, 2024, 12:28 AM motion

EBB42 not going into DFU mode 16 messages

Jul 14, 2024, 6:46 PM Solved setup

Can I fix my octopus v1.1? 3 messages

Jul 13, 2024, 5:28 PM other setup

Moving toolhead power my fan 4 messages

Jul 12, 2024, 8:08 PM Solved other

Part fan runs 100% 6 messages

Jul 12, 2024, 5:40 AM Solved setup

Stepper Driver Issue 8 messages

Jul 12, 2024, 2:44 AM setup

I'm having layer shifts 5 messages

Jul 12, 2024, 1:51 AM motion

Hotend still reading wrong even after numerous fix attempts 2 messages

Jul 11, 2024, 8:03 PM setup

BTT TMC5160T 14 messages

Jul 10, 2024, 12:35 AM Solved setup

hot end thermister reports 158.7°C when off 6 messages

Jul 9, 2024, 4:19 PM Solved setup

Part Cooling Fan not working BTT Octopus MAX EZ - New VC4 Build 16 messages

Jul 8, 2024, 7:30 PM Solved other setup

new vcore-3.1 500 do not extrude whit LGX and rapido phateus v2 7 messages

Jul 7, 2024, 5:01 PM other

Deki Goes BRRRRRR at 0% fan speed and full send at boot 11 messages

Jul 5, 2024, 6:38 PM Solved setup

PT1000 Temperature readout minus (-)225 degrees 20 messages

Jul 5, 2024, 4:07 PM setup

Unable to flash controller 18 messages

Jul 5, 2024, 3:24 AM Solved setup

Communication timeout during homing Z 3 messages

Jul 4, 2024, 4:45 PM other setup

Octopus v1.1 not sending signal to heated bed *fresh RatOS instal* 17 messages

Jul 2, 2024, 4:14 AM other setup

Rough HG15 linear rails 6 messages

Jun 28, 2024, 10:10 AM motion setup

VC4 * 500 Gantry warping issues as printer heats 107 messages

Jun 28, 2024, 3:50 AM setup

Usb devices being reset during print 25 messages

Jun 22, 2024, 3:41 PM other

Auto levelling problem 33 messages

Jun 21, 2024, 11:59 AM motion other setup

hot end thermister reports 126.8°C when off 9 messages

Jun 19, 2024, 10:09 PM Solved setup

Fresh V-Core 4 RatOS 2.1 RC1 klipper fails to connect 3 messages

Jun 19, 2024, 4:15 PM Solved setup

X and Y moving simultaneously 3 messages

Jun 18, 2024, 5:48 AM motion Solved

Beacon start up print Move out of range 5 messages

Jun 16, 2024, 10:39 PM motion setup

Input shaper error in config 7 messages

Jun 16, 2024, 10:17 PM setup

Some help reading the log. 34 messages

Jun 16, 2024, 8:13 AM setup

mcu 'toolboard': Unable to connect 6 messages

Jun 15, 2024, 2:25 PM setup

Network change! 3 messages

Jun 15, 2024, 8:39 AM setup

wifi module 3 messages

Jun 14, 2024, 4:00 PM other setup

Klippain install broke RatOS 3 messages

Jun 13, 2024, 12:17 PM Solved other

How do I reverse my controller fan 11 messages

Jun 13, 2024, 4:12 AM Solved other